SelectBlinds Urban Edge Roller Installation Guide

SelectBlinds Urban Edge Roller

Product Specifications

• For indoor use only
• Maximum Size: 800 mm / 31.49 in
• Minimum Size: 105.5m9 min
• Width: 30 mm / 1.18 in

Product Usage Instructions – Cassette

Installation Instructions

Read the instructions carefully before assembling and using the product. The assembling process can be completed by non-professionals.

WARNING: Young children can strangle in the loop of pull cords, chains, and tapes. To avoid strangulation and entanglement, keep cords out of the reach of young children. Do not tie cords together.

Make sure cords do not twist together and form a loop.

Mounting Options

Inside Mount: Place on the chain side. Wall mounted only.

Outside Mount: Install the safety device so there is no slack in the chain loop.

Installation Steps

1. Mount the cassette according to the mounting option chosen (inside or outside mount).
2. Install the child safety device as specified in the childsafe manual.
3. Ensure there is no slack within the loop of the cords.

FAQ

Q: Can I install this product on my own?

A: Yes, the assembling process can be completed by non-professionals. However, make sure to carefully read and follow all the instructions provided.

Q: What should I do to prevent strangulation hazards for young children?

A: Keep cords out of the reach of young children, avoid tying cords together, and ensure cords do not form a loop. Install the child safety device as specified in the manual.

Installation Instructions – Cassette

Read the instructions carefully before assembling and using the product. Assembling process can be completed by non-professionals. For indoor use only.

WARNING

• Young children can strangle in the loop of pull cords, chains and tapes, and cords that operate window coverings.
• To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords may become wrapped around a child’s neck
• Move beds, cots and furniture away from window covering cords.
• Do not tie cords together.
• Make sure cords do not twist together and form a loop.

WARNING
Install the child safety device as specified in the childsafe manual.

Removal

INSTALLATION INSTRUCTIONS – STANDARD BRACKETS

Installation
Read the instructions carefully before assembling and using the product. Assembling process can be completed by non-professionals. For indoor use only.

WARNING

• Young children can strangle in the loop of pull cords, chains and tapes, and cords that operate window coverings.
• To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords may become wrapped around a child’s neck
• Move beds, cots and furniture away from window covering cords.
• Do not tie cords together.
• Make sure cords do not twist together and form a loop.

Removal

WARNING
The Safety Device is a fixed tension device for operating ball-chains that form a continuous loop. This device must be applied in chain loops that do not have a breakaway design. The safety device prevents free-hanging loops in operating chains. Install the safety device at the maximum distance possible from the control mechanism to prevent slack in the loop. Upon delivery to the end user, the device must be attached to the chain. The tensioning device is provided with fasteners for installation to wooden wall substrates. Please read the following information when installing the tensioning device. For other wall types please use appropriate screws that are suitable for your wall.

• A: Inside Mount: Fully recessed shade and safety device
• B: Inside Mount: Partially recessed shade and safety device
• C: Outside Mount: Shade and safety device outside window

INSTALLATION TIPS

Installation – Fascia

Read the instructions carefully before assembling and using the product. Assembling process can be completed by non-professionals. For indoor use only.

WARNING

• Young children can strangle in the loop of pull cords, chains and tapes, and cords that operate window coverings.

• To avoid strangulation and entanglement, keep cords out of the reach of young children. Cords may become wrapped around a child’s neck

• Move beds, cots and furniture away from window covering cords.

• Do not tie cords together.
  Make sure cords do not twist together and form a loop.
  

• Step One:

  • Use the brackets to mark the screw locations
  • On outside mount, make your marks so the distance from the outside edge of the bracket to the outside edge of the other bracket equals your ordered width
    Note: Brackets must be level to each other for the shade to operate properly (for both inside mount and outside mount)

• Step Two:

  • Recommend you pre-drill the screw holes using a 5/64″ drill bit where you marked the screw locations
  • Mount the brackets using 2 screws for each bracket
    Note: On outside mount, the screws will be installed on an angle. This is normal and the screws may not be flat against the bracket.

Installation

• Step Three:
  The idle side attachment should be on the opposite side of the chain (simply click into the bracket if it is not already attached)

• Step Four:
  Slide the chain guide onto the clutch

• Step Five:
  Slide the idle side of the shade on to the idle side connector

• Step Six:
  Click the control side of the shade the bracket

• Step Seven:
  Connect the fascia to the top of the brackets and rotate it down to click into the bottom side of the brackets

• Step Eight:
  On outside mount only, attach the bracket endcaps over each bracket

• Final Step:
  Install the child safety device

Installation – 2-on-1 Open Roll with a single control

Read the instructions carefully before assembling and using the product. Assembling process can be completed by non-professionals. For indoor use only.

• Step One:

  • Use the brackets to help mark the screw locations
  • On outside mount, make your marks so the distance from the outside edge of the left bracket to the outside edge of the right bracket equals your ordered width and the intermediate bracket is exactly in the middle of those brackets
  • Brackets must be installed level to each other for the shade to operate properly (for both inside mount and outside mount)

• Step Two:
  Intermediate bracket will come assembled with 3 components

• Step Three:
  Start with the left shade by sliding the idle side of the shade onto the pin of the intermediate bracket

• Step Four:
  Click the control side of the shade into the left bracket

• Step Five:
  With the right shade, slide the idle side onto the pin of the intermediate bracket

• Step Six:
  Click the control side of the shade into the right bracket

• Step Seven:

• Slide the bracket cover on the left and right bracket

• Final Step:
  Install the child safety device

Installation – Fascia: 2-on-1 with Continuous Chain

Read the instructions carefully before assembling and using the product. Assembling process can be completed by non-professionals. For indoor use only.

Fascia 2-on-1 (Intermediate) Installation

CORNICE INSTALLATION

INSIDE MOUNT

NOTE:
The brackets for your shade will come installed on the cornice (if the cornice and shade are ordered together).
Install cornice before installing the shade.
Inside Mount cornices are made 1/8″ less than the ordered width of the shade.

1. Hold the cornice to the top of your window frame and set it back until it is flush with your wall or until it is touching the back of the window opening. Be sure the cornice is centered in the opening.
2. Predrill holes through the cornice for your screws:
   • a. 12″ maximum from each side
   • b. Space between screws should not exceed 24″
3. Secure your cornice to the window by screwing through each hole you predrilled .
4. Once the cornice is mounted, you can then install the shade.

CORNICE INSTALLATION

OUTSIDE MOUNT

NOTE:
The brackets for your shade will come installed on the cornice (if the cornice and shade are ordered together).
Install cornice before installing the shade.
Outside Mount cornices are made 1″ wider than the ordered width of the shade.

1. Make sure the surface you intend to install your cornice hardware is sturdy enough to support the brackets. You will need to screw into wood studs that are strong enough to securely bond with the included screws or you will need to use fasteners to securely support the brackets. Please note secure fasteners are not included.
2. Center the cornice over the window opening at your desired height. Mark the position of the ends of the cornice on the wall. Measure in 6″ from each end and using the cornice bracket mark the screw holes with a pencil. If you have additional cornice brackets, space them evenly between the outer brackets. Make sure all the mounting brackets are level with one another.
3. Pre-drill the holes for each cornice bracket and then secure the brackets to your mounting surface.
4. Place the cornice on top of the brackets and center it to the window. Check again that the cornice is level. Hold the cornice in place and screw through the top of each bracket into the cornice.
5. Once the cornice is secured to each bracket, then you can install the shade.

References

• YouTube

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>