ALTRONICS PowerQuest Touch Screen Control System Instruction Manual
- June 17, 2024
- ALTRONICS
Table of Contents
Touch Screen Control System consists of two components (16 Channel- three), the Touch Screen (TS) and the Switch Panel Module(SPM) MAIN and AUX. The PowerQuest system can control the switching of 16 circuits. 6 circuits are predefined and 10 are custom. Each circuit can be fused up to 30 amps. The system should be installed be a certified automotive technician. Connect GROUND wires first!!!!
Wirin g System:
IGN Ctrl – Connect ignition signal or other switched signal to IGN Ctrl
terminal. This input will allow (Trig enabled (IGN)) channels to turn on/off
when ignition is turned on/off. Also, ignition can control system power up and
down if Ignition/Switch Power off is enabled in SETUP menus (see Configure
section) Connect Ign Ctrl to both MAIN and AUX modules when used.
Trig1 Trig 2 – This input will allow (Trig enabled) channels to turn on/off
when Trig 1 or Trig2 signal is turned on/off. Feature must be enabled in SETUP
menus (see Configure section)
Configure:
System will be Configured with default settings. To change those settings press the “Config” button on the switch panel screen.
Brightness – Sets screen brightness
Sleep – Turns screen off when no user press for sleep time. Press anywhere on
screen to turn back on. Can also be controlled by ignition signal.
Security Enable – Activates optional Lock Screen and Manual Sleep.
Enable 16 Ch– Activates second module when installed
Ign/Switch Power – Enables external ignition or switch input into external IGN
terminal to control system power up and down (Sleep).
Display Amps – Activates displaying current level for each switch channel.
Blue Tooth – Bluetooth setup for BT control, optional.
Select Channel- Press to see list of available switch Channels, then select
channel to modify
Not all features are available for all circuits.
Channel – Displays channel name.
Pick button: Use +/- buttons to cycle thru preset buttons
Custom button: Select to enter custom label for button.
Soft Start: Check box to allow slow increase in current at turn on.
Switch Type: Select switch behavior.
Normal, Momentary, Pulse (turn signal), Burst (high speed pulse, with pause),
SOS (distress pulse), Dim/PWM (Select 0-100% power for dimming lights or
running motor at different speeds)
Max Current: Select maximum fused amperage for circuit (0-30amps).
Limit Enabled: Check box to limit circuit turn on by temperature settings
Temperature: Select temperature to enable.
Hysteresis: Differential temperature change required to activate. (Ex: With a
2º hysteresis and a 100º temperature setting the controller will allow the
actual temperature to go to 98º before turning off Fan and Pump and back to
100º to turn on again) allow the actual temperature to go to 98º before
turning off Fan and
Auto Enable: Check to enable. Allows switch channel to automatically turn on
and off other selected channels when activated/deactivated.
Auto Switch Delay: Time in seconds selected circuit is delayed from turning on
if it is Auto Enabled from another channel.
Trig Enable: External control to turn channel on or off. Requires wired
connection to IGN (ignition), Trig 1 or Trig 2 terminals on module. Save:
Saves changes and returns to previous Menu.
Lock Screen:
Master Code: On the back of Module (not the touch screen) there is a tag with
the systems Master 4 digit program code and a Temporary User Code. You can use
the Master code to program your User code. The Master code can always be used
to reset User code.
Reset User Code: Use following sequence to program User Code. User code cannot
be Master Code or 1234.
- Key in Master Code and press ENTER
- Use Back arrow to delete Master Code from window.
- Key in number USER CODE XXXX and press ENTER
- Press Enter Again
Now User Code is set.
Unlock Screen: Key in User code and press ENTER SLEEP: Press Sleep to force
sleep mode.
If fuse is tripped Switch Panel circuit button will turn off and “FUSE” message will be shown on button label. Pressing button again will reset fuse.
PowerQuest Demonstration video (www.altronicsinc.com/switch- panels/powerquest-1.html) for more details.
TECHNICAL SUPPORT:
Email: Tech@AltronicsInc.com
When sending a unit in for repair or update: Fill out a “Service Form” which
is available from the Technical Support Section of our website->
www.AltronicsInc.com
WARRANTY:
by is warranted for 1 Year against any defect in materials and workmanship
from date of purchase.
ALL WARRANTIES AND GUARANTEES ARE VOID if the enclosures are opened or altered
or if equipment is connected to system that is not supplied or authorized by
Altronics Inc.
shall not be liable for injury, consequential, or other types of damages
resulting from the use or misuse of the
is to be used for off road purposes only!
1411 S. Roselle Rd. Schaumburg, IL 60193 Phone
847-923-0002 Fax
847-923-0004
www.AltronicsInc.com
Verify the size of this print against dimensions given before use!
Documents / Resources
|
ALTRONICS PowerQuest Touch Screen Control
System
[pdf] Instruction Manual
PowerQuest Touch Screen Control System, PowerQuest, Touch Screen Control
System, Screen Control System, Control System, System
---|---
References
- Drag Racing Weather Stations, Data Loggers, EGT, Air/Fuel, Wideband, & Lithium Batteries - Altronics
- Drag Racing Weather Stations, Data Loggers, EGT, Air/Fuel, Wideband, & Lithium Batteries - Altronics
- PowerQuest Touch Screen Switch Panel PDM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>