Lighting Legends Firestorm 1.5M Phoenix Eco Advanced Patio Heater Installation Guide

Lighting Legends Firestorm 1.5M Phoenix Eco Advanced Patio Heater

Product Specifications

• Model: Firestorm Patio Heater
• Hardware Included : M6 Allen key, M8 nut, 3x M6 Bolts, 3x Feet, M8 washer, M8 bar
• Tools Required (Not Included): 13mm spanner

Assembly Instructions

Position Firestorm Body

Place the Firestorm body upside down on a flat surface and lean the round face against an edge to keep it upright.

Insert M8 Bar

Insert the M8 bar into the thread plate on the boom of the Firestorm body by turning clockwise until fully threaded.

Attach Support Post

Place the support post onto the Firestorm body with the castellations aligned through the slots.

Install Base Plate

Carefully place the base plate onto the support post ensuring proper alignment with castellations and M8 bar.

Secure with Washer and Nut

Place the M8 washer over the M8 bar, hand thread the M8 nut onto the bar, and tighten clockwise with a 13mm spanner. Ensure the blue side of the nut faces up.

NOTE: Do not overtighten; only tighten until there are no gaps between the nut, washer, and base plate.

Attach Feet

Insert an M6 bolt through a hole on the base plate and hand thread one of the feet onto the bolt clockwise. Repeat for all three feet.

Complete Assembly

Turn the assembled Firestorm over onto a flat-level surface. Tighten all three feet clockwise using the included Allen key. Congratulations! Your Firestorm Patio Heater is now ready to use.

Product Usage Instructions:

Positioning

Place the Firestorm Patio Heater on the flat-level ground in the desired position in your garden.

Fill Hopper

Open the lid and fill the hopper with ENplus A1 Wood Pellets, then close the lid.

Add White Spirit

Pour one cap full of white spirit into the burning chamber, ensuring it spreads over the pellets.

Ignite

Using a long-reach lighter, light the white spirit in multiple locations if possible.

Place Glass Tube

After lighting, carefully slide the glass tube down through the top ring onto the burning chamber.

Extend Burn Time

To extend the burn time, add more pellets through the lid. Do not let pellets go below a quarter of the tube before refilling to avoid smoking.

Maintenance

If flame decreases due to ash build-up, remove ash through the open boom door using an appropriate tool or heat-resistant glove. Poking the grate may help but is not always necessary.

(FAQ):

• Q: How do I know when to refill wood pellets?
• A: Refill wood pellets before they go below a quarter of the tube to prevent smoking and ensure continuous flame.
• Q: How can I prevent damage during assembly?
• A: Avoid overtightening nuts and bolts; follow tightening instructions carefully to prevent damage.

Assembly

Firestorm Patio Heater – Assembly

Firestorm Patio Heater Checklist:
Please ensure you have all hardware and tools required before assembly.

1. Place the Firestorm body upside down on a soft flat surface and lean the round face against a soft edge to keep the Firestorm body upright.

2. Insert the M8 bar into the thread plate on the boom of the Firestorm body by turning clockwise, ensure it is fully threaded into the body before proceeding.

3. Place the support post onto the Firestorm body with the castellation fitted through the slots.

4. Carefully place the base plate onto the support post ensuring the castellations and M8 bar through the plate and it sits securely.

5. Place the M8 washer over the M8 bar and onto the base plate, hand thread the M8 nut onto the M8 bar and tighten clockwise with a 13mm spanner, ensuring the blue side of the nut faces up. TAKE CARE NOT TO OVERTIGHTEN THE NUT. ONLY TIGHTEN UNTIL THERE ARE NO GAPS BETWEEN THE NUT, WASHER AND BASE PLATE. TIGHTENING BEYOND THIS POINT RISKS DAMAGE.

6. With the Firestorm still upside down, insert an M6 bolt through a hole located on the outer edge of the base plate. Hand thread one of the feet onto the bolt clockwise.
   Repeat this step for all three feet.

7. Turn the assembled Firestorm over and place it on a flat-level surface. Tighten all three feet clockwise using the included Allen key.

Congratulations!
Your Firestorm Patio Heater is now ready to use. Please refer to the Lighting & Maintenance Leaflet overleaf

Maintenance

Firestorm Patio Heater – Lighting & Maintenance

Firestorm Lighting Checklist:
Please ensure you have all the lighting tools necessary before starting.

General safety

The Firestorm heater gets very HOT! Please ensure that it is always somewhere where it is safe. Site the Firestorm on flat level ground in a location protected from the wind, or shield the lower portion on all sides of the Firestorm pictured above. This will prevent potential extinguishing of the fire during use. Remember that even after it has gone out the Firestorm will remain hot for around half an hour. Be mindful of the safety of anyone who is going to be in close proximity. The heater has a glass cylinder. The glass tube is made from Borosilicate glass and so is heat resistant. Care must be taken to ensure it is not knocked by something hard. Particular care is necessary when taking apart, cleaning and assembling. As the Firestorm gets going you may notice a humming noise coming from the tube, this is normal. This will subside once the Firestorm reaches full burn. Never spray water onto the hot tube. The sudden change in temperature may cause the glass to break. Always let the Firestorm cool down before disassembly, moving or cleaning.

1. Place the Firestorm Patio Heater on the flat-level ground in the desired position in your garden.

2. Open the Lid fill the hopper with wood pellets and close the lid.

3. Pour one cap full of white spirit into the burning chamber, and try to spread the white spirit over the whole area of pellets while pouring.

4. Using a long-reach lighter, light the white spirit through the top of the burning chamber. Try and light in multiple locations if possible.

5. Once lit, carefully slide the glass tube down through the top ring and seat on top of the burning chamber.

6. Extend the burn time by adding more pellets to the Firestorm through the lid.
   Important: Make sure the Firestorm does not have less than a quarter of a tube of pellets left before refilling. Refilling beyond this point can choke the fire and cause it to smoke rather than flame. If pellets are not visible in the bottom of the hopper then there is a risk the Firestorm will go out upon refilling.

7. If you notice the flame getting smaller this is most likely due to ash build-up, this can easily be removed by scraping the ash out through the open bottom door of the firestorm.
   Important: The door will be hot to touch during use. Only touch the door using an appropriate tool or with a heat-resistant glove for safety. Poking the grate through the open door can also help but may not be necessary.

8. Allow the Firestorm to burn through the remaining pellets and it will self-extinguish.

9. Once completely cool, remove the glass tube and clean it with the included sponge cleaner. Wet the sponge with cold water and push it through the glass tube in one smooth motion. Rinse the inside of the tube with a garden hose and allow to air dry inside the Firestorm.

10. Clean all ash from the Firestorm using the scraper and poker tools in the accessory kit. The ash is 100% compostable so feel free to add it to your compost bin once cold

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>