AguaStella AS75CB Champagne Bronze and Black Kitchen Sink Faucet Instruction Manual
- June 17, 2024
- Aguastella
Table of Contents
Installation Instructions
AS75
Features
- Sedal ceramic disc cartridge: Tested with 500,000 cycles
- Construction: Spout: Silicone; Sprayer Head: Brass; Body and Handle: Zinc Alloy
- Pull-down sprayer with dual function: Spray and stream
- Spout swivels 360° for complete sink access
- Neoperl aerator: Save water and reduce energy costs
- Neoperl Softpex connecting hoses with SPX inliner Length: 29-1/2″; Thread diam.: 9/16″; Connection size: 3/8″
Standards
- Third party certified to IAPMO, ASME A112.18.1/CSA B125.1 and all applicable requirements referenced therein including NSF 61/9G
- Complies with California Proposition 65 and the Federal Safe Drinking Water Act
Dimensions
- Overal Height: 17-3/10″
- Spout Height: 7-7/10″
- Spout Reach: 8-7/10″
- HoleSize:1-3/8″
- MaxDeckThickness:2-1/2″
- MinClearancetoBacksplash:3″
ToolsNeeded
Safety Tips! WARNING!
- Always shut off the water supply before removing the existing faucet and/or installing a new one. Turn on the hot and cold knobs on the existing faucet to release the built-up pressure.
- Always wear safe glasses when cutting or soldering water supply lines.
- Keep the drain covered to avoid losing parts.
- AguaStella is not liable for any damage to the product, countertop or sink due to improper installation.
Installation
-
Remove the rubber washer, metal washer and the black locknut from the threaded shank (Figure 1).
-
Check before installation: (Figure 2).
A. Check and make sure the threaded shank is tight in the faucet’s body by screwing with your hand. (Otherwise the faucet will not be secured tight to the counter/sink with the black lock nut.)
B. Check and make sure the 2 hoses (hot and cold water connection hose) inside the faucet’s body are tight with the cartridge inside the faucet’sbody by screwing with your hand one by one.(Otherwise water may leak from the inside body of the faucet.) -
Place the faucet body into the faucet hole of the deck/sink (Figure 3). A standard 1-3/8″ hole is required for this faucet.
-
From underneath the deck/sink, slide the rubber washer followed by the metal washer all the way up to the threaded shank (Figure 4).
-
Screw the black locknut all the way up to the threaded shank until it is tight (Figure 4).
-
Screw the female ends of the connecting hoses to the corresponding hot and cold water supply alves by using an adjustable wrench or plier (Figure 5).
-
Screw off the faucet’s sprayer head. Turn on the water supply (Figure 6). Let the water run for about 30 seconds to flush any dirt that maybe in the system. Then screw on the sprayer head and make sure the screen/washer is in place. Test the faucet by turning the faucet on and off. Make sure the water flow is right and no leaks. If it leaks, turn the water supply off and contact AguaStella at aguastellausa@outlook.com.
Trouble-Shooting Guide
| Issue | Cause | Solution |
|---|---|---|
| Faucet cannot be secured tight to the counter with the black lock nut. | The | |
| threaded shank is not tight in the faucet’s body. | Screw the threaded shank |
tight in the faucet’s body with your hand.
Water is leaking from inside of the faucet’s body.| The 2 hoses inside the
faucet’s body may become loose from the cartridge inside the faucet’s Body.|
Screw the 2 hoses tight to the cartridge with your hand one by one.
Water is leaking from under the handle.| The adjusting ring may be worn out or
the cartridge nut may become loose.| Replace the adjusting ring or tighten the
cartridge nut.
The aerator is leaking or the water flow becomes inconsistent.| The aerator
may become dirty or the seal ring may be worn out.| Clean the aerator or
replace the seal ring.
Water flow becomes smaller or even stop.| The screen/sprayer head’s up side
may be blocked by particles from water.| Screw off the faucet’s sprayer head,
remove the screen/ washer, turn on the faucet and let water run for about 30
seconds to flush any dirty that may be in the hose. Then screw on the sprayer
head and make sure the screen/washer is in Place.
Notice!
- Screw off the sprayer head once per season, remove the screen/washer, turn on the faucet and let water run for about 30 seconds to flush any dirt that maybe in the hose, then screw on the sprayer head and make sure the screen/washer is in place.
- Keep the Allen Key included in the package. It can be used for assembling the faucet.
- Keep the Blue Aerator Key included in the package. It can be used to screw off the aerator to clean or replace.
- Email us at aguastellausa@outlook.com if you meet any other issue. We’re ready to help and reply within 24 hours.
Product Information
| NO. | PART NAME | QTY |
|---|---|---|
| 1 | handle | 1 |
| 2 | M5 screw | 1 |
| 3 | cartridge cover | 1 |
| 4 | O-Ring | 1 |
| 5 | cartridge nut | 1 |
| 6 | ø25-cartridge | 1 |
| 7 | cartridge core | 1 |
| 8 | body | 1 |
| 9 | O-Ring | 1 |
| 10 | connecting tube | 2 |
| 11 | O-Ring | 1 |
| 12 | wearing ring | 1 |
| 13 | connector | 2 |
| 14 | wearing ring | 1 |
| 15 | M5 screw | 1 |
| 16 | spray arm | 2 |
| 17 | O-Ring | 1 |
| 18 | connector | 1 |
| 19 | spout | 1 |
| 20 | motion hose | 1 |
| 21 | spout | 1 |
| 22 | connector | 1 |
| 23 | sleeve | 1 |
| 24 | magnet | 1 |
| 25 | sheet metal | 1 |
| 26 | MS screw | 1 |
| 27 | rubber washer | 1 |
| 28 | check valve | 1 |
| 29 | sprayer | 1 |
| 30 | O-Ring | |
| 31 | shank | 1 |
| 32 | rubber washer | 1 |
| 33 | metal asher | 1 |
| 34 | locknut | |
| 35 | connecting hose | 2 |
https://www.aguastellausa.com
E-mail: aguastellausa@outlook.com