Yojoker BW-98 Heating Bottle Warmer User Manual
- June 17, 2024
- Yojoker
Table of Contents
**Yojoker BW-98 Heating Bottle Warmer User Manual
**
Cleaning
- Unplug the USB cabik long press the” button for 3 seconds to power off
- Pour boiling water or detergent into the bottle warmer and use brush provided to dean it
Note:
Do not rinse with running water directly Do not directly immense in water for
cleaning
What’s Included
- Protable Bottle Warmer x1
- Milk Powder Container x1
- Bottle Adapter x8
- Charging Cable x1
- Cleaning Brush x1
- User Manual x1
Operation Cautions
For your and your child’s safety and health, Warning!
Always use this product with adult supervision. Keep this product out of reach
of children
- Please inspect the product before each use.
- Please clean the product before first use.
- Please use this product under the ambient temperature of 50-95°F.
- Do not use corrosive cleaning agents, anti-bacterial cleaners or high concentration detergents, they may cause components to crack. Should this occur, please replace them immediately.
- Do not leave the product in sunlight, heat or sterilizing solution for a long time, as it may reduce use effects.
- Heating time should not be too long: After the temperature is up to the certain temperature, it can keep breast milk warm but heat preservation time should not last more than half an hour for the breast milk will go bad and is not good for baby’s health.
- After heating milk you should check the temperature of milk whether suitable or not, for example, drip the milk on your opisthenar.
- The heating time provided in this instruction is a reference value for heating time under specific conditions. Actual heating time will be affected by different conditions, such as environment temperature, baby bottle material, initial temperature and water volume.
- Do not immerse the product in water or other liquid.
- Do not expose the product to direct sunshine, heat or hot environment
- Do not touch the stainless steel parts during heating to avoid scalding.
- Please clean and dry the product when it cools down after the use.
- lt is recommended that use this product with adapter (5V/2A).
- Do not lose the sealing ring when you clean the bottle to avoid leakage.
- There is built-in battery in the bottle warmer. Do not use the product in the strong electric field in case that it will damage the battery protector.
- Please unplug the product when it is not in use. Do not charge for a long time in case of fire or other accidents.
- This product can be used by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge if only they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not play with the product.
How to Charge
Charge Method
Withdraw the dust cover on the back of the warmer, plug the Type-C connector
in charging port and plug in the adapter.
Being charged
When the warmer is charging, the power indicator showed on the digital display
flashes.
Fully charged
When the warmed is fully charged, the digital display will auto-off. Once
unplug the USB cable, the digital display will auto-on and in standby status.
Parts Guide
Digital Display
-
Power Indicator
Once the warmer is turn on, it shows the current battery level. The full charge state is 4 cells. When the warmer is heating, the power indicator does not appear. -
Temperature
Once the warmer is turn on, it shows the current temperature. After the temperature level is set (5 levels:98-105-109-116-121°F), the warmer goes into heating mode. the current temperature is displayed during the heating process. When the liquid reaches the set temperature, it will be kept at this temperature and the heating unit will auto shut off. -
Red Dot
When the red dot is blinking, it means the warmer is heating up.
Use Method
-
Choose the adapter and install it.
-
Put the warmer upside down and screw on the baby bottle.
-
Return the warmer to its original position
-
Long press the “+” button for 35 to power on. Then the display lights up and the product in standby status.
-
One press the”+”/”-“button.Figure will flash, the warmer is in standby mode. There are 5 temperature levels, in the order of “98-105-109-116-121″°F.
-
Then the figure stops flashing and the warmer goes into heating mode. When the liquid reaches the temperature you set, it will be kept at this temperature and the heating unit will auto shut off.
Bottle Converter Marking
Serial number| Product picture| Converter identification|
Adapter brand| Fit bottle caliber
---|---|---|---|---
1| | B| MAM| 50
2| | P| Pigeon| 50
3| | A| Evenflo| 50
4| | N| AVENT| 50
5| | D| NUK| 50
6| | T| DrBrown’s| 50
7| | C| DrBrown’s| 40
8| | M| Medala| 40
Product Specifications
Model: BW-98
Charging Voltage: DC-5V/2A
Work Power: 60W
Bottle Adapter: 8 Different Models
Digital Display: battery level/temperature display/heating reminder
FQA
-
Can I use the bottle warmer to keep water/milk warm over night?
- a. You can keep water warm overnight.
- b.You can keep milk warm overnight. But less than half an hour is suggested. Milk is perishable if stored over half an hour.
-
What should I do when white or rust-colored spots appear inside the bottle warmer?
The white or rust-colored spots are scale deposits. Mix white vinegar or citric aciddescalers with over 50 C hot water, leave the solution in the bottle warmer for about 10 minutes until all scale has dissolved. -
What is the bestwater temperature for baby to drink?
- a.98°F/105°F for protein powder/probiotics b.98°F/105°F/109°F/116°F for milk powder/water.
Customer Service
We provide 30 Day-money-back and 1-year worry-free warranty serivce.If you have any questions, please contact us through Amazon’s “Contact Seller”.we will be happy to serve you and guarantee a 100% satisfactory solution.
Any questions? Feel free to contact us first.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>