ammoon AMG03 Compact 5 Channel Mic Line Mixer USB User Manual

ammoon AMG03 Compact 5 Channel Mic Line Mixer USB

IMPORTANT SAFETY INSTRUCTIONS – READ FIRST

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

This symbol, wherever it appears, alerts you to the presence of uninsulated Dangerous voltages inside the enclosure that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.

Read Instructions

Retain these safety and operating instructions for future reference. Heed all warnings printed here and on the equipment. Follow the operating instructions printed in this user guide.

Do not open

There are no user serviceable parts inside. Refer any service work to qualified technical personnel only.

Power sources

Only connect the unit to mains power of the type described in this user guide or marked on the rear panel.
The power source must provide a good ground connection.

Power cord

Use the power cord with sealed mains plug appropriate for your local main supply as provided with the equipment. If the provided plug does not fit into you outlet consult your service agent. Route the power cord so that it is not likely to be walked on, stretched or pinched by items placed upon or against.

Grounding

Do not defeat the grounding and polarization means of the power cord plug. Do not remove or tamper with the ground connection on the power cord.

Moisture

To reduce the risk of fire or electrical shock, do not expose the unit to rain, moisture or use in damp or wet conditions. Do not place container of liquid on it, which may spill into any openings.

Heat

Do not locate the unit in a place close to excessive heat or direct sunlight, as this could be a fire hazard. Locate the unit away from any equipment, which produces heat such as: power supplies, power amplifiers and heaters.

Environment

Protect from excessive dirt, dust, heat, and vibration when operating and storing. Avoid tobacco ash, drink spillage and smoke especially that associated with smoke machines.

Handling

Protect the controls from damage during transit. Use adequate padding if you need to ship (he unit. To avoid injury to yourself or damage to the equipment take care when lifting, moving or carrying the unit.

Servicing

Switch off the equipment and unplug the power cord immediately if it is exposed to moisture, spilled liquid or the power cord or plug becomes damaged during a lightning storm or if smoke odor or noise is noted. Refer servicing to qualified technical personnel only.

Installation

Install the unit in accordance with the instruction printed in the user guide.

Operating Elements and Connections

1. MIC/LINE IN: This combined jack can be used to connect mono signal, such as XLR
   microphone or 1/4” line level.
   Note: Please choose balanced cable and MIC to connect. Do not use the unbalanced ones. When the unit is powered on, remember not to connect the high level signal to XLR Mic In, which may damage the unit.

2. Stereo input LINE IN (RCA jacks) to connect an audio source with line signal level (e.g. CD player) to channel CH2/3.

3. Stereo input 2-TK (RC Ajacks) to connect stereo line signal level sources.

4. Stereo outputs MAIN MIX (RC Ajacks) to connect the input of an amplifier or a recorder.

5. USB port (type B) to connect a computer or a power supply unit with USB connection; When operating the mixer with a computer, it is possible to use this port as an audio output (output of the mixed signal) and as an audio input (feed-in of audio data to be reproduced via channel LINE/USB)

6. PHANTON Power LED

7. PHANTON Power Switch

8. HEADSET connections (MIC/PHONES)
   Note: Headset connected to the built-in microphone, must be connected MIC IN and PHONES in order to avoid unnecessary noise. The audio input here is sent to channel 1.

9.  Echo control to adjust the Echo effect component for channel CH1

10.  2TK control switch: This is the assign control of 2TK input . When this control is engaged, the signal of 2TK will be assigned to MONITOR(8). When the controls disengaged, the signal of 2TK will be Assigned to MAIN MIX (4) and USB (5).

11. Volume control MONITOR/PHONES for the headphone output MONITOR/PHONES (8).

12. Overload LEDs CLIP for the stereo output signal adjusted with the control MAIN MIX (13).

13. MAIN MIX control to set the level of the output signal sent via the outputs MAIN MIX (4) and the USB port (5).

14. Control GAIN for channel CH1 to set the input amplification.

15. High frequency control HI and low frequency control LO for channel CH1.

16. PAN This is the panorama control or balanced control. This control is used for stereo effect field of the signal. Set this control in middle position, signal level of Channel L & R will be same.
    When the control is set to top stop, only Channel L receives the signal, Channel R can not. Vice versa

17. PEAK LED This is clip LED indicator of CH 1 level. When this LED illuminates, it means that PFL CH1 level is clipped.

18. Control LEVEL for channel CH1.

19. From LINE IN/ USB Play source selector switch.: Pushing the button in, the signal of channel LINE/USB comes from USB PLAY(computer); When the switch is disengaged, signal will be from RCA jacks of channel 2/3.

20. To LLINE/USB Switch assigns signal to main mix.

21. Control LEVEL for channel LINE / USB

22. POWER switch

23. Output level indicator.

24. To LINE/USB switch assigns signal to Monitor (Phones).

Applications

This compact 5-channel audio mixer with USB interface is suited for universal applications, e.g. For audio recording on the computer.

The mono input channel allows to connect a (phantom-powered) microphone; The stereo inpi channel allows to connect an audio source with line signal level. In addition, the mixer is pro with connections for a recorder and headphones. The mixed signal is sent to the output via a 1 jacks and the USB port. It is also possible to use the USB port as an input to transfer audio da from the computer to the mixer. When connecting the mixer to a computer, power is supplied the USB connection. When operating the mixer without a computer, either use a suitable pow supply unit with USB connection to operate the mixer.

Setting into Operation

Prior to connection/disconnection and prior to each switching on, the output controls MONI1 /PHONES (11) and MAIN MIX (13) should be turned back to “min”.

1. As audio sources, microphones and/or audio sources with line signal level (e.g. effect unit! musical instruments, players) can be connected to the five input channels.
   Mono channels CH1:Ined XLR/6.35mm jack are available as inputs (1)

   • Connect microphones to the balanced XLR jack or HEADSET jacks
     The XLR jack (CHI) and 3.5mm jack (HEADSET MIC IN) always supplies a +18V phantom power and it thus suitable for a condenser Microphone operated with this phantom power. Caution!When phantom power switch is on (7) Do not connect a microphone with unbalanced output via XLR plug; it may be damaged by the phantom power.

   • Connect mono sources with line level to the 6.35 jack.

   • Do not use both CH1 Input ( l)-MIC IN and HEADSET (8)-MIC IN

2. The input LINE IN(2) of the stereo channel LINE/USB allows to connect an audio source with line signal level (e.g. CD player) via RCA plugs: L= left channel, R= right channel.1

3. The input 2TK(3) of the stereo channel allows to connect an audio source with line signal level (e.g. Recorder , MP3 player…e.t.c)

4. The 3.5mm jack MONITOR/PHONES(8) allows to connect stereo headphones (impedance 16 ohm). Thus, you will be able to monitor the output signal or the input signal of the jacks 2TK (3) via headphones.

5. At the stereo MAIN MIX(4), the output signal adjusted with the MAIN MIX. control (13)i present. This output allows to connect an amplifier or a second mixer via a RCA plug.

Operation with a computer

When operating the mixer with a computer, either use the audio software supplied with the operating system or an audio software installed additionally. Various programs for audio reproduction/ recording are available on the internet free of charge.

1. Start the computer. Connect the USB port (5) to a USB connection on the computer via the 1 cable provided. Switch on the mixer with the switch POWER(7)[position ON]. The LED O /CHARGE(6) lights up according to the battery charge status (chapter 3.3).

2. The computer recognizes the USB interface of the mixer as an external device for audio ir and audio output, e.g. as “USB Ear Microphone” . depending on the operating system required drivers (standard drivers of the operating system) are available on the computer.
   Note: If not all drivers required are available on the computer, install them, e.g. via the orig CD of the operating system. Restart the computer after installation, if necessary.

3. Open the reproduction / recording program and make the required settings for audio reproduction via the mixer or audio recording from the mixer (user manual of the program it is not possible to record or reproduce any sound, make sure to activate the USB interface audio input or audio output in the system settings of the operating system of the computer.

Hint: If the mixer is connected to a computer and to any units GND via their mains cables (I amplifiers), there may be hum noise due to ground loops. To eliminate this noise, connect mixer to the corresponding unit via a ground isolator.

Operation with power supply unit

Via its USB connection, the power supply unit must provide an output voltage of 5V and an output current of 500mA. Connect the power supply unit to the USB port (5) via the USB cable provided, then connect it to a mains socket. Switch on the mixer with the switch POWER(22)[position ON]. The LED ON(22) lights Up.

Operation

The following steps merely serve as an aid, other ways of procedure are also possible.

1. As a basic setting first
   • set all control GAIN (14), EQ (15), PAN (16) to mid-position.
   • Turn all control LEVEL (11, 13, 18, 21) back to the left stop.
2. When a microphone is connected to the jack MIC IN (1) of HEADSET ( 8 ) , speak into the microphone and turn up the corresponding control LEVEL(18) until you obtain a good microphone signal. If you need to turn up the control LEVEL completely for this purpose, further turn up the control GAIN(14). However, if the led PEAK (17) lights up and is not extinguished immediately, turn back the control gain, The led PEAK must only briefly light up with level peaks.
3. Use the panorama control PAN(16) to place the microphone signal on the stereo base. Adjust the sound with the controls HI and LO (15).
4. Turn up the control LEVEL(21) for channel LINE/USB until you obtain a good input. LINE /USB audio source can be select come from USB port (5) or LINE IN Rea jacks (2) by button switch (19).
5. Use the controls LEVEL (18, 21) to mix the input signals of channels CH1and LINE/USB or to fade them in and out. When a channel is not used, set it’s control to “MIN”.
6. Use the controls MAIN MIX (13) to set the level of the output signal that is sent via the jacks MAIN MIX(4) and the USB port (5). If one of the overload LEDs CLIP (12) shows red, turn back the control MAIN MIX accordingly.
7. The headphone output MONITOR/PHONF(8) allows to monitor the output signal of the mixer. For this purpose, the button 2TK TO MAIN MIX/ PHONE (10). Adjust the headphone volume with the control MONITOR/PHONES (11).

WARNING: Never adjust the headphones to a very high volume. Permanent high volumes may damage your hearing! Your ear will get accustomed to high volumes which do not seem to be that high after some time. Therefore, do not further increase a high volume after getting used to it.

Features

Sensitivity/ Impedance

Mic: ………………………… 1.3mV/l .7KΩ(Gain max)
Line, channel 1:…………… 5mV/12KΩ(Gain max)
Line,channel 2/3: ………….260mV/16KΩ
2-TK in: ……………………. 300mV/22KΩ
Output level:………………. 5.8V max (MAIN; MONITOR)
Frequency range:…………. 20 -21000 Hz
THD:………………………… ≤0.05%
S/ N ratio: …………………. 8l dB (A weighted) Equalizer
Bass range: ……………….±!5dB / 80Hz
High range :……………….±15dB/ 12kHz
Headphone impedance:. …..≥16Ω
USB interface :………………Fully compliant with USB 2.0, Windows 98SE,Windows 2000, XI or higher,Mac OS 9.0.4 or higher, 10.X or higher.
A/D-D/A …………………….16 Bit, 44.1 kHz or 48 kHz, USB selectable from computer 0.4 ms A/D latency @ 44.1 kHz
Phantom power :……………+18V
Power supply :……………… 5V/500mA via USB interface
Dimensions: …………………10145135 mm(4″x5.3″x1.6″)
Weight :………………………480 g( 1.06 lbs)

Windows is a registered trademark of Microsoft Corporation in the USA and other Countries.
Mac OS is a registered trademark of Apple Computer, Inc. in the USA and other Countries.
Subject to technical modification.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>