Phenyx Pro PDP-2-1H1B Dual Digital Wireless Microphone System Owner’s Manual

Phenyx Pro PDP-2-1H1B Dual Digital Wireless Microphone System

Specifications

• PWR-P1/2 Wireless Receiver:
  • Battery Capacity: 1500mAh
• PWR-P Bodypack Transmitter:
  • Microphone Type: Headset/lapel mic
  • Microphone Element: Condenser
  • Polar Pattern: Omni
  • Sensitivity: -96dB
  • Signal-to-Noise Ratio: 96dB
  • Frequency Response: 110Hz-18kHz
  • Output Impedance: 2.2kΩ
  • Sample Rate: 48kHz
  • Bit Rate: 24-bit
  • Total Harmonic Distortion + Noise (THD+N): 0.1%
  • Charging Interface: USB-C
  • Charging Time: About 2 hours
  • Working Time: About 5.5 hours
• PWH-P Handheld Transmitter:

Product Usage Instructions:

Step 1: Power up and pair up the receiver and transmitters

1. Ensure the receiver and transmitters are fully charged.

2. Turn on the receiver and transmitters by pressing the power button.

3. Pair the receiver with the transmitter(s) by following the pairing instructions in the manual

Step 2: Link up with the sound system

1. Connect the receiver to the sound system using the appropriate audio cables.
2. Adjust the volume levels on both the receiver and sound system to achieve the desired sound output.

Wireless Tips

• Keep the transmitter and receiver within the recommended operating range for optimal performance.

FAQ

• Q: How do I mute the handheld microphone?
• A: Tap the button on the handheld transmitter to mute the microphone. The LCD screen will flash when the transmitter is muted.
• Q: What should I do if the bodypack transmitter is not charging?
• A: Ensure that the bodypack transmitter is properly connected to the USB-C charger. If it doesn’t light up, check the connection and try a different charging cable if needed.

SYSTEM DESCRIPTION

System Overview

Phenyx Pro always adheres to the mission of inspiring people to achieve next- level sound performance and exploring better tenchniques to enhance the wireless experience. The PDP-1/2 series is our new digital solution that balances convenience and professionalism. With an adjustable UHF frequency design, it boasts advanced digital circuitry for noise immunity and delivers stellar sound for small-scale indoor and outdoor performances. This is a go-to audio solution for weddings, church sermons, karaoke, broadcasts, meetings, etc.

System features

• 48kHz/24Bit UHF digital circuitry transmits encrypted signals to avoid signal crosstalk and deliver pure fidelity sound.
• Tunable frequency design makes the system fearless to interference. (The US version has 15 frequencies for each transmitter. EU version has 5 frequencies for each transmitter.)
• The dynamic cardioid microphone delivers stable performance.
• Rock-firm wireless coverage is up to 200ft without interference.
• Transmitter mute function for your convenience and safety.
• Plug-and-go hookup. One-tap frequency selection from the transmitter.
• Available to link up several units simultaneously.
• The portable receiver and bodypack transmitter with the universal USB Type-C charging port offer ultimate convenience and fast charging.
• 1500mAh battery of receiver and 550mAh battery of bodypack transmitter for long-lasting battery life.
• The whole system is durable-metal built with elegant silver colour.

System Component

Receiver

Accessories

Transmitters

FUNCTIONS OF PARTS

Receiver
PWR-P1/2
The PWR-P1 receives the signal from only one transmitter, which should be in CHA. It can not receive the signal from a transmitter in CHB.
The PWR-P2 can receive signals from two transmitters which should be in CHA and CHB.

1. Power/Pair button: Long press this button for 2 seconds to turn on/off the receiver, and tap it to initiate synchronization with the transmitter.

2. USB-C port: The USB-C charging port for the receiver.

3. Antenna: For better signal reception, please keep it upward while using.

4. Battery indicator: It doesn’t light up when the receiver is turned on with enough battery. And it will turn red and flash quickly when the receiver is in the low battery status. While charging, the indicator will stay red; then, it will turn off when the receiver is fully charged.

5. RF indicator: It stays on, indicating the receiver is receiving signals. When it flashes slowly, the receiver is not paired up with the transmitter; while flashing quickly, the receiver and transmitter are successfully synced.
   NOTE: If you want to verify whether the second transmitter of the PDP-2 is synced, please make sure both transmitters are in different channels and that the RF indicator flashes quickly and then stays on when you turn on each one. Also, you’d better do a sound check for both transmitters to confirm the successful synchronization.

6. 6.35mm TS connector: It is compatible with the 6.35mm TS jack of an audio mixer, amplifier or other devices to output the audio signal received from the transmitter.

Transmitters

Handhled transmitter PWH-P

Bodypack transmitter PWB-P

1. Microphone capsule
   NOTE: Please make sure the sound source is toward the capsule.

2. Bodypack antenna

3. Mini 3-pin XLR jack: Connect a headset/lapel microhone.

4. LCD display: It shows real-time battery indicator, frequency number and channel number. The screen shows “—-”
   when the transmitter is on standby.

5. Power button : Long press this button for 2 seconds to turn on/off the transmitter.
   NOTE: For handheld mic, tap this button to mute the mic. The LCD screen flashes when the transmitter is muted.

6. CH button: Tap this button to adjust the channel frequency.
   NOTE: For the detailed frequency, please check it on the frequency list.

7. Mute button: Tap this button to mute the bodypack. The LCD screen flashes when the transmitter is muted.

8. Battery compartment: Install AA batteries with the correct polarity to charge the handheld mic.

9. USB-C port: The USB-C charging port for the bodypack transmitter.

10. Power indicator: It lights red when the bodypack transmitter is charging and turns blue when fully charged.

NOTE: It doesn’t light up when the bodypack isn’t charged to the USB-C charger.

OPERATION GUIDANCE

Step 1: Power up and pair up the receiver and transmitters.

1. Make sure the receiver is fully charged before using it.

2. Long press the power button of the receiver for 2 seconds to turn it on.

3. For the handheld mic, unscrew the battery cover of the transmitter and install fresh batteries with the correct polarity.
   For the bodypack transmitter, make sure it is fully charged.

4. Long press the power button of the transmitter for 2 seconds to turn it on.
   NOTE: The LCD screen of the transmitter shows “—-” in standby mode.

5. Tap the CH button of the transmitter to select the desired frequency.
   NOTE: A frequency accommodates only one wireless channel. Please ensure that the frequencies
   of each transmitter are different from each other.

6. Tap the power/pair button of the receiver to pair it up with the transmitter.

7. Check the indicators of the receiver to ensure effective synchronization.

8. When pairing up the second transmitter for the PDP-2 system, please make sure to select a different frequency from the first one and follow the procedures above.

Step 2: Link up with the sound system

1. Make sure the gain and volume for input channels of the mixer/party box/karaoke machine are set to the minimum.

2. Insert the receiver into the 1/4″ input jack of the mixer/party box/karaoke machine to output the sound.
   NOTE: Make sure the antenna keeps all the way upward. If it does not, please use the angle TS adapter included in the package for it.

3. Adjust the gain and volume to ensure effective audio output.

WIRELESS TIPS
If you encounter wireless interference or dropouts, try the following suggestions:

• Replace the transmitter batteries.
• Make sure the battery of the receiver is sufficient.
• Choose a different frequency channel.
• Avoid approaching the receiver and transmitters with metal or other dense materials.
• Place the receiver as high as possible on the equipment rack.
• Remove any devices causing possible signal interference, such as cellphones, computers, media players, two-way radios, and digital signal processors.
• Keep transmitters more than 6 feet (two meters) apart.

TROUBLESHOOTING

SPECIFICATION

PWR-P1/2 Wireless Receiver

PWR-P Bodypack Transmitter

PWH-P Handheld Transmitter

Frequency List
For the single wireless system, the transmitter operates in CHA. For the dual wireless system, one transmitter operates in CHA the other onerates in CHR. Frequencies vary from country to country

WARRANTY

TECHNICAL SUPPORT & WARRANTY INFORMATION

Our warranty to you
Phenyx Technology (“Phenyx”) warrants Phenyx products against evident defects in material and workmanship for one year from the date of original purchase for use. This warranty is valid exclusively in the US and applies only to the original owner. If you discover a defect covered by this warranty, Phenyx will repair or replace the product at our sole discretion using new or refurbished components. Performance of repairs or replacements under this Warranty is subject to registration of your product at www.phenyxusa.com/registerproduct.
Product failures not covered by this warranty
This warranty covers defects in manufacturing that arise from the correct use of the device. It is limited to defects in materials or workmanship and does not cover electrical or mechanical damage resulting from abuse, misuse, unauthorized modification, lack of reasonable care, extreme heat, cold, damage due to natural forces, or corrosive environments. This warranty does not cover the normal wear and tear on covers, housing, connectors, and accessories.
Limits of liability
If your Phenyx product fails or does not perform as warranted, your sole recourse shall be to replace or repair it as described above. Phenyx will not be liable to you or anyone else for any damages that result from the failure of this product. These damages include but are not limited to, the following: lost profits, lost savings, lost data, damage to other equipment, and incidental or consequential damages arising from the use of or inability to use this product. IN NO EVENT PHENYX SHALL BE LIABLE FOR MORE THAN THE AMOUNT OF YOUR PURCHASE PRICE, NOT TO EXCEED THE CURRENT LIST PRICE OF THE PRODUCT.

How to obtain service under this warranty
If you are receiving a defective system or you have any questions regarding operation or warranty cover, please contact us at support@phenyxpro.com with any questions or concerns and a Phenyx Pro representative will contact you to assist. You can also reach out to us through our Facebook page: www.facebook.com/phenyxusa/ or our official website: www.phenyxpro.com.

Thank you for purchasing the Phenyx Pro PDP-1/2 Series.
For the best results and the utmost satisfaction for your new unit, please read this manual carefully to ensure proper operation, and keep it for future reference. For more information, please visit our store: www.phenyxpro.com.

References

• Phenyx Pro | Professional Wireless Microphones, IEM systems, Mixers

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>