IMIPAW DU3L-WY Automatic Cat Food Dispenser WiFi Cat Feeder User Manual

IMIPAW DU3L-WY Automatic Cat Food Dispenser WiFi Cat Feeder

Product Information

Specifications

• Model: DU3L-WY
• Power Supply: 5V/1A power adapter or 3 pcs alkaline D size batteries (not included)
• Recording Time: Maximum of 10s
• Food Size Range: 2-12 mm in diameter

Product Usage Instructions

Installation

1. Remove the feeder from the box.
2. Place the feeder in a suitable location.
3. Combine the food tray with the base of the feeder.

Connect the Power Supply

1. Plug the 5V/1A power adapter into the wall socket and connect it to the device.
2. Open the battery compartment at the bottom of the feeder and install 3 pcs alkaline D size batteries (not included) as a backup power source.
3. The LED light will turn on to indicate that the feeder is powered on.
4. Note: Before turning on the power, make sure that all parts are clean and completely dry.

Put Pet Food into Food Tank

1. Fill the food tank with dry pet food.
2. Close the food tank lid.
3. Note: Do not place canned, wet, or moist pet food. The recommended pet food size range is from 2-12 mm in diameter.

Recording

To record a voice message:

1. Long press the recording button for 3 seconds until you hear a beep to start recording.
2. Continue holding the button throughout your recording.
3. Release the button when you hear two beeps, indicating that the recording has ended.
4. Note: The device supports a maximum of 10s recording.

Note: The recorded message can be played by pressing the recording button or it will be played automatically when feeding.

FAQ

1. How do I switch between WiFi mode and Hot Spot mode?

To switch between the two network modes:

1. Ensure that the power is turned on and the network is not configured.
2. Press and hold the set button for 7 seconds until you hear three beeps.
3. The red indicator will be on for 6 seconds and the blue indicator will switch to slow flashing, indicating hot spot network configuration mode.
4. Repeat the operation to switch between WiFi mode and Hot Spot mode.

2. Can I use wet pet food in the feeder?

No, the feeder is designed for dry pet food only. Do not place canned, wet, or moist pet food in the food tank.

3. How long does the battery last?

The battery life depends on usage, but it is recommended to replace the batteries when they are low or every few months to ensure continuous operation.

Safety Instruction

1. Children must be accompanied by adults to use it.
2. Do not use the feeder for pets which cannot reach the food tray or have physical disabilities.
3. Do not immerse the base part in water, which will damage electronic components such as control panel.
4. Do not put any foreign objects into the pet feeder.
5. Do not put canned or wet food into the feeder.
6. Do not disassemble the equipment by yourself.
7. Do not modify the pet feeder.
8. lf the equipment can not work or have damaged accessories, do not try to repair the pet feeder by yourself. Contact the seller immediately and solve it.
9. Please make sure the feeder is unplug and power off when not using or cleaning it.
10. lf the plug is damp, please turn off the socket rather than trying to unplug the power.

Notice

1. Please purchase hard plastic protector from hardware store to protect plugs and power cord then prevent your pet from damaging the accessories.
2. Do not put the pet feeder in a high-temperature place.The temperature should be within the range of – 10 ℃~40 ℃.
3. Please use an alkaline Size D battery for power supply. Do not use rechargeable batteries.
4. Check the battery regularly. Please replace the battery before having a trip.
5. Do not lift the pet feeder directly with the cover, food bucket and food tray. Hold the base with both hands to lift and carry, while keeping the device in an upright position.
6. Only applicable to dry food with a diameter of 2-12mm. Larger food may get stuck or block the food outlet.
7. Please read all the notices on the packing and manuals carefully

Product Overview

Front View

1. Food Tank Lid
2. Food Tank
3. Control Panel
4. Food Outlet
5. Body
6. Food Bowl

Bottom View

1. Speaker
2. Battery Compartment
3. DC Interface

BUTTONS AND DISPLAY OVERVIEW

• Recording Button: When the device is unlocked, press and hold for 3s until a beep is heard then the device starts to record. Keep holding the button throughout your recording. Release the button when you hear the beep twice, this indicates that the recording has ended. The device supports a maximum of 10s recording.

Note:

• The default of the meal call playback is 1 time, and the meal call plays when feeding time is up.
• When the device is unlocked, to delete your recording, press and hold the recording button for 3s. Release immediately after a beep is heard. When 2 beeps are heard, no recording is taken.
• Locked Button: Under unlock state, long press for 6s and the red led light flashes twice, lock the device. Under locked state, long Press for 6s and the red led light flashes twice, unlock the device.

Note:

• When press the feed button, feed a portion manually, it is unlocked
• When the device is locked status, long press set button for 6s to restore factory setting.
• feed: Feed Button: When the feeder is unlocked, press once to feed a portion manually.
• set: Set Button: When the power is turned on and the network is not configured, the blue indicator flashes quickly by default, which is WiFi configuration mode. Press and hold for 7 seconds to hear three beeps, the red indicator is on for 6 seconds and the blue indicator switches to slow flashing, which is hot spot network configuration mode. Repeat the operation to switch between the two network modes.

LED INDICATORS

Blue

| Flash every 0.5| The feeder is in WiFi mode, ready to connect with App.
---|---|---
Flash every 2-3s| The feeder is in hot spot mode, ready to connect with App.
Stay Solid| Connected to WiFi and fully operational
Stay for about 6s| WiFi mode/Hot Spot mode switch

Red

| Flash| Abnormal or low voltage
Flash Twice| Locked/Unlocked
Stay for about 6s| WiFi mode/Hot Spot mode switch

Packing list

After opening the product package, please confirm whether the machine is in good condition. Please check the list to confirm whether the accessories are complete.

• The Feeder ×1
• The power adapter ×1
• Power Cord ×1
• Product Manual ×1

IN THE BOX

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

1. this device may not cause harmful interference,
2. and this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part l5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televis ion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technic ian for help.

To maintain compliance with FCC’s RF Exposure guidelines,This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Instructions

Installation

• Remove the feeder from the box.
• Place the feeder in the suitable location.
• Combine the food tray with the base of the feeder.

Connect the power supply

• Plug the 5V/1A power adapter into the wall socket and connect the device.
• Open the battery compartment at the bottom of the feeder, and install 3 pcs alkaline D size batteries (not including) in case of outa.
• The LED light is turn on to indicate that the feeder is powered on.

Note: Does not including battery . Before turning on the power, make sure that all parts are clean and completely dry.

Put pet food into food tank

• Fill the food tank with dry pet food then close the lid.

Note: Do not place canned, wet or wet pet food. The recommended pet food size range from 2-12 mm in diameter.

Recording

• Long press for 3s until you hear “di” and start recording. The recording time does not exceed 10s, After you release your hand, you will hear “didi” to indicate that it has been saved. If you are not satisfied, you can repeat this step to replace the previous recording.

note:

1. A recording will be played by pressing the recording button
2. A recording will be played when feeding

Lock/unlock button

• under unlock state,Long press for 6 seconds and the red indicator light flashes twice to lock the machine, then long press again for 6 seconds and the red indicator light flashes 2 times to unlock.
• In the locked state, you can press and hold the RESET button to restore the factory settings

Note:
Pressing the feeding button in the locked state does not work, it must be unlocked for normal use. The APP operation is not affected in the locked state.

Feeding

• Manual feeding: short press to serve 1 portion.

Note: The feeding plan will not be affected

Reset

• Switching the network configuration mode: When the power is turned on and the network  is not configured, the blue indicator flashes quickly by default (WiFi quick connection configuration mode), press and hold for 7 seconds to hear three beeps, The red/blue indicator is always on for 6 seconds and then switches to slow flashing (hot spot network configuration mode). Repeat the operation to switch between the two network modes.

PETTECH APP SPECIFIC OPERATIONS

1. Scan the QR code or search for “PETTECH” on the APP Store to download the app. Sign up or log in to your account
2. Open the APP, select Home page, tap “Add Device” or “+” in the upper right corner
3. Turn on the Bluetooth on your phone. Enter the interface, wait for the device “DU3L-W-01” to be discovered automatically, then click add
4. Enter a WiFi password (the name cannot be used in Chinese, the password cannot be used for special symbols)
5. Waiting for the device to connect the network, showing successfully added, then next step
6. After successful, you can customize the name of device, click on the upper right corner to finishe this step
7. Manually Feeding: enter the interface, you can choose the portions as required, click” Feed” to feed immediately
8. Click” Meal Plan” on the main interface to add feeding schedule
9. Choose feeding time, feeding days, and feed number. Click “save”
10. Slide the scheduletimer to delete it
11. View the logs: click”Feed Record”, you can view the feeding records
12. Share your feed: enter the interface, click the icon in the upper right corner to enter the settings option
13. Enter the setting menu option and click”Share device”
14. Click”Add” and enter the account and save. Share the device with multiple people

Cleaning and Maintenance

Please clean the feeder regularly to keep your pet’s health. When it starts to get dirty and a lot of loose food in the food trough, you can remove the food cover to clean it. Please clean the feeder base and the control panel with a soft, damp cloth. Do not put these parts into water. Do not put the product in the dishwasher, otherwise it will be permanently damaged!

Specification

• Food Tank Capacity:3L
• Power supply: DC 5V/1A power adapter; 3pcs alkaline D Size batteries
• Power adapter: AC110-240V input, DC5V output
• G.W:1.65KG
• Size: 18.2×18.2×28.3cm
• BC-091-D

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>