Artin-X 39 Inch Smart LED Pendant Light User Manual

Artin-X 39 Inch Smart LED Pendant Light User Manual

Product Details

Product & Accessorie

Smart Pendant Light x1

Remote Control x1

Expansion tube x2

Self-tapping screwx2

User Manual x

This luminaire is only suitable for safe use in areas below altitude 2000m.

1. Please be sure to cut off power to prevent electric shock before installation.
2. Installation must be carried out in strict accordance with the instruction.
3. Improper installation may easily cause accidents such as fire, electric shock or lamp falling.
4. Installation must be performed by a qualified electrician to avoid danger
5. “Pendant Light – Angel” hereinafter is referred to as “Pendant”.

Installation Guide

Installation must be carried out in strict accordance with this user manual. In consideration that the luminaire has two parts, it is recommended that installation is performed by two qualified installation person to avoid falling and causing damage due to improper installation

Hole Drilling

1. Select a suitable position on the “ceiling”, and the distance between the mounting holes of the suspension plate is about 430mm;
2. Drill holes of depth ≥35mm with a drill bit with diameterq6mm; put 2 expansion tubes into the holes and then lock the screws into the expansion tubes, leaving a height of 10mm.
   

2. Suspension Plate Removal – Power Cord Connection – Bottom Cover Fixing

1. Turn the “disassembly knob” on both ends of the “suspension plate” counterclockwise, and pry it off manually or with a screwdriver; (Note: Pry the suspension plate off carefully and slowly to avoid damaging the light.)
2. Peel off the power wire by 6-8mm, wind it into the hole of the suspension plate, press the terminal and insert it into the terminal port and then loosen the terminal to lock the wire.
3. Buckle the disassembled “bottom cover” at the position of screw holes, then move to the right to lock it, and then lock the bottom cover with a screwdriver. 

Attention :

1. External power wire must pass through the middle of installation bracket to avoid wire crimping while installation.
2. Keep clear the power wire, and avoid the bottom cover pressing the wire. Insecure installation may cause falling and damage.
   

Suspension Plate Fixing

1. Wrap the power wire around the “inner side slot of suspension plate”, and bury the wire in the shell following the direction of the “red line”, and the wire length can be adjusted;
2. Snap the upper cover back to the bottom cover, and turn the “disassembly knobs” clockwise.
   

Attention:

Power wire can be buried in the “inner side slot of suspension plate” by a circle or a half circle.

When it is buried by one circle, the “suspension plate upper cover” together with the lamp body needs to be rotated by 180° before it can be installed.

Balance Adjustment

As shown in the figure, long press the wire lock pin, push/pull the wires through to adjust the length of the wires and maintain the light horizontal. Loosen the wire lock pin to fix the length.

Product Certification
Product Name Smart Pendant Light -Homies
Inspection date————————————-
Inspector————————————

Please read the user manual carefully before using the product. You can watch the “installation guidance” video clips by visiting our amazon product page. Manufacturer: LightByYun (Xiamen) Intelligent Technology Co., Ltd.
Address: No.66-2, Gaoqi North 2nd Road, Fujian Pilot Free Trade Zone, Xiamen City,
China Email: artin_x@163.com

Connect to Remote Control

Turn on the pendant, press on button 4 (Previous track) and button 5 (Next track) at the same time within 1 min. after powered on to pair up. When the signal lights on the remote control panel continuously flash 5 times together, the pairing is successfully done.

If you simultaneously long press on button 18 (Daytime scene) and button (21) (Guest scene), all the signal lights on the remote control panel will flash once together. This means the devices are successfully disconnected

1 BLE/TF card mode change

2 Speaker timer

3 Play/pause button

4 Previous track

5 Next track

6 Volume up, long press for continuous increase

7 Volume down, long press for continuous decrease

8 Reset button

9 No function

10 Light timer

11-14 RGB control area

15) Brightness control

16 Color temperature control

17 Power On/Off button

18 Daytime scene

19 Warm scene 20 Reading scene

21 ) Guest scene 22 Timer signal

BLE/TF Card Mode Change

It is set as BLE mode when powered on, press on ‘BLE/TF card’ button to switch. MP3 tracks will be played once the TF card is detected. It will automatically return to BLE mode if no TF card is detected over 5 seconds.

Speaker Timer

Set timer to turn off music. Speaker timer and light timer shares the same signal light (1 signal light on when pressed once, meaning a 10-minute timer. 2 signal lights on when pressed twice, meaning a 20-minute timer. 3 signal lights on when pressed 3 times, meaning a 30-minute timer. Signal lights will all go off when pressed 4 times, meaning no timer is set.) You can check out timer status with a long press.

Light Timer

Set timer to turn off light. Light timer and speaker timer shares the same signal light (1 signal light on when pressed once, meaning a 10-minute timer. 2 signal lights on when pressed twice, meaning a 20-minute timer. 3 signal lights on when pressed 3 times, meaning a 30-minute timer. 4 signal lights on when pressed 4 times, meaning a 40-minute timer. 5 signal lights on when pressed 5 times, meaning a 50-minute timer. Signal lights will all go off when pressed 6 times, meaning no timer is set.) You can check out timer status with a long press.

Play/Pause Button

Short press on the button controls the speaker to play or pause the music. Long press to turn off Bluetooth speaker. You can turn on Bluetooth speaker by a short press after it is powered off

Reset Button
Do not use the reset button if possible. Only under the condition when system is not working, please use a needle to press on reset button for 3-5 seconds.

Power On/Off Button
Long press to turn on/off all power including light and speaker. Short press to turn user-cho- sen main light / RGB light on or off. For example, if the light choice is under main light, a short press on button can turn the main light on/off.

No Function Button
“No function” button is for locking the main light. Press “No function” button once, the main light doesn’t work. Press the button again, it resumes operation.

RGB Control Area

RGB Switch:

Control RGB power on/off. Short press to switch one side to another.

Single Color:

Switche between RGB 7 colors, including red, orange, yellow, green, blue, indigo, and violet.

Mode:

Switche between RGB 3 modes, including streaming mode, color-changing mode, and rainbow mode.

Brightness:

Control RGB brightness change. Short press to level up one step of brightness, totally 5 levels. The brightness will jump back to the lowest level after a short press at the highest level of brightness, and so forth.

MUSIC SLEETING

1. Power on the pendant.
2. Turn on Bluetooth on your mobile phone, and search for device “epoch he”.
3. Click on the device name to enable automatic pairing. The sound ‘ding-dong’ will come up when pairing is successfully done.

• For devices successfully paired, the pendant will connect automatically when next time it is powered on. Only paired devices can be used. TF card is not provided along with the product. Maximum storage of TF card adopted cannot exceed 128G and can only be applicable under MP3 format file.

Note: The remote control is rechargeable via USB Type-c port.

Attention while Use

1. When the light is just turned on and when it is just off, the plastic part may cause a tiny cracking sound due to the elasticity. It is not a malfunction situation.
2. In places with weak radio waves (such as steel reinforced structure), the pendant may have effect on televisions or radios with indoor antenna.
3. The remote control may not respond so well if you are controlling other electronic appliances (such as air conditioner) very close to the pendant.
4. If you are not going to use the light for a period, please turn off the wall switch.
5. Please note that the controllable distance may differ due to ceiling and wall materials.
6. Light status may change if power failure occurs, or if power is cut off and resumed after.
7. The remote control may not respond so well if you are using 3D television aside.
8. Every LED light source may have minor difference in between as the color and lumen may vary under the same brand.
9. Do not connect with other dimmer switches to avoid possible malfunction.

Basic Parameter

Product Name: Smart Pendant Light -Homies

Product Size: 1000x75x45mm

Product N.W.: approx. 1500g

Rated Voltage: 100-240V~50HZ/60HZ

Total Power: 50W (max.)

Light Source Power: 33W (60x1W/LED +10×1.5W/LED)

Color Temperature: 2700-7000k

Audio Channel: 2.0

Frequency: 80Hz-20KHz

CRI: 95@4000k

Power Factor: >0.9

Operating Temperature: -10~+40°C

Operating Humidity: 0%~85% RH

Speaker Power: 6W (RMS)

Warranty: 3 years

Output Power: 2x5W

THD+N: ≤0.5%

S.P.L ( average): 85db @0.1V/0.5m tested

Power & Impedance: 80

Speaker Unit: 2×2.5inch full range+2x $ 65mm passive radiators

Product Feature

Repairment and Maintenance

1. Advice to clean and check (every 6 months) on a regular basis. Lack of checking may cause accidents such as fire, electric shock, and fallen lights.
2. Please note that dry, soft cloth is appropriate to use after cleaning with mild detergent. Do not use any sharp object to touch the surface of the product.

Safety Precautions

1. Please confirm if the operating voltage is aligned with this product. Inappropriate voltage will cause damage on product and would have risks on safety.
2. Please make sure to take off all the packaging and tape before installation to avoid fire.
3. The pendant is not waterproof. Please do not adopt it in wet areas such as bathroom or outdoors. Avoid any bad isolation that may cause accidents like fire or electric shocks.
4. During light in operation or when light is just turned off, do not touch the LEDs and surrounding areas so as not to burn accidentally.
5. Do not put high-temperature objects, such as heater and gas stove, right under the light to avoid fire.
6. Light source cannot be changeable by user. Please do contact the manufacturer, service distributor or people with equal capability to proceed with the change.

Restore Factory Settings

If you continuously turn power on and off 5 times (2 seconds on and 2 seconds off), the light will be restored to factory settings with a breathing performance on lights.

When the light is being adopted under a new network environment, please restore to factory settings, and connect with the network again.

Product Malfunction List

Lights on when power is off.
Remote control doesn’t work
Lighting flashing when operating with remote control.
Light scene automatically changing when power is on.

Hazardous substance and content

This table is listed according to regulation SJ/T11364.
O : The content of the hazardous substance in this homogeneous material follows the regulation GB/T 26572.
X : The content of the hazardous substance in this homogeneous material exceeds the content regulated in GB/T 26572

Warranty Service

The after-sale service of pendant light Angel is strictly compliant with “the Law of the People’s Republic of China on the Protection of Consumer Rights and Interests” and “Product Quality Law of the People’s Republic of China”, implementing 3 Guarantees Certificate service as follows.

From the next day of your purchased date, if you found any fault conditions listed from “Product Malfunction List”, our after-sale center would provide below service for free if product confirmed malfunctioned.

Warranty not Covered

1. Unauthorized repairment, misuse, collision, neglect, improper use, water ingress, accident, modification, or damage, alteration, marking, and anti-counterfeiting marking. 2
2. year warranty period exceeded.
3. Damage due to force majeure.
4. Circumstances that do not aligned with the “Product Malfunction List.”
5. Product or accessories malfunctioned that aligns with the “Product Malfunction List” due to human forces. The product may be damaged under the condition of using dimmer switches, non-rated voltage, non-applicable adapter, or non-regulated environment

3 Guarantees Certificate for Pendant Light – Angel

Customer name Mr./Ms.————————————–

Contact number—————————————————

Customer address————————————————

Series no._____

Product code___

Purchased Date_____

Purchased from store_____

Store address_____

Invoice number_____

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>