HomeHome App V3 NodeMCU Lolin Installation Guide

Device ID: XXXXXX
NodeMCU Lolin V3

HomeHome.App Installation

You can always get help direclty from us. Please write an email to info@homehome.app we can make the setup together
YOU NEED DUPONT CABLES & 1/2/4 CHANNEL 5DC RELAY BOARD 5DC POWER SUPPLY & MICRO USB CABLE
IF YOU HAVE NODEMCU BASEMENT YOU CAN USE 6-24 DC POWER SUPPLY WE RECOMMEND 12DC 1A FOR BASEMENT
Attention 220 AC is very dangerous, get help from an electrician to connect 220 AC wires to the device. When you power up the device, it will broadcast HomeHome-XXXXXX WiFi network.
Password:”homehome”
Device LED will NOT blink when it gets power. After this setup finished, normal working process;
LED will blink after 30 seconds (3 times) when device restarts.
You can always make your own NodeMCU following this guide:
https://www.homehome.app/forum/tutorials/1-start-with- flashing-a-nodemcu
Important: Please write your gmail address and device id (XXXXXX) to info@homehome.app for Google Home and smart.homehome.app WEB UI activation
Setup
Please use iPad / iPhone / Android tablet or mobile phone for setup. You will see captive portal for device setup. If it doesn’t start, disconnect from WiFi and unplug-plug the device, reconnect to WiFi.

1. Select device type: Custom On-Off Setting (1-2-4 relays in 1 system) or Custom Shutter Setting (Only 1 system with 2 relays for roller shutter) See pin definations and wiring at the end

2. Select switch type: Momentry

3. Enter your GMAIL address which you use in your Android Phone, this is required for http local server login also.

4. Enter a static IP (optional) We recommend you set it now or you will have to reset the device and re-start this setup OR you can manage your static IP with your router if it has a static ip feature.

5. Select your Home WiFi and enter it’s password. If it is not in the list, you can enter SSID manually. Be sure that you write correct password or it will not connect to your network!
   Q:What happens when my router is off?
   A:Device will try to connect a few minutes and begin to broadcast it is own network (HomeHome-XXXXXX)

6. Save settings and wait 3 seconds. Unplug and plug the device.

X-HM://001451BWVHOME
Enter the code manually:111-88-111
Apple HomeKit Setup
7-You can pair HomeKit in 90 seconds after restart, pair code is 111-88-111
Select your room and a name for your device. WAIT 1 Minute after succesful pairing.
+44 736-784-6094
Please Write for Help

• If you will not use HomeKit, wait 3 minutes for 3 led blink. Enter your device ip (step 10) to a web browser. Enter your full gmail address to connect http server. Click “Settings” button and activate “Skip HomeKit Pair Standby Time” Click “Restart Device” button.

Google Home Setup
8-Open Google Home app from your Android phone.
Tap +> Set up device> Works with Google> ”+HomeHome”> Login
Be sure that your gmail address is the same with
“Android phone account”,
“+HomeHome login account”,
“Device setup” (step 3),
“WEB UI Setup” (step 9)
WEB UI setup – https://smart.homehome.app
9-You must register your device, Sign-in with the same gmail account. Click “Manage” tab and activate Device ID:XXXXXX unplug-plug or restart the device from http server.
HTTP Server
10-Enter IP address of your device to a web browser.
Q:Where to find IP?
A: -Long press to accessory in HomeKit app and see ip of the device.
-You can find XXXXXX in your router’s DHCP list (MAC address)
Enter your full gmail address (with @gmail.com)
3.Party Apps
You can control HomeHome.App with 3th party apps.Your email adress must be gmail so don’t add @gmail.com for HTTP GET request.

• Turn on 1. relay: ‘https://ip.address/1/on?myEmail‘
• Turn off 1. relay: ‘https://ip.address/1/off?myEmail’

All state replies are in array for example: [0,1,2,2] 0 –> off , 1 –> on , 2 –> none

• Get all relay states: ‘https://ip.address/all?myEmail‘

1-2-4 relay devices are using the same firmware so we push all together. You can easly understand this is a 2 relay device. First relay is off, second relay is on in this example.
Extra Features:
Remote control with HomeKit: You can use HomeKit without leaving an iPad-Home Pod-Apple TV in your home.

• You can control your device with “Hey Siri”,”OK Google”
• Make Scenes or Routines for full automation.
• OTA – Over the air update will be published if needed.
• You can turn off local HTTP server for security.
• You can change device name in local HTTP server settings for WEB UI and Google Home.
• “Turn Back” Switch to last position on power failure.
• “Local Mode” Set device work offline (without internet) If enabled you can not use Google Home and Web interface.You must first register the device (with internet connection) to use this feature.You can use HomeKit (if paired) and local interface (HTTP server) to control the device. Note that device must always join to a router.
• Long press to accessory in HomeKit app and see ip of the device.Support @ http://homehome.app/support For more help: info@homehome.app

Example 4 Relays On-Off nodemcu GPIO setting:
Relay1=5(d1)
Relay2=4(d2)
Relay3=14(d5)
Relay4=12(d6)Button1=13(d7)
Button2=3(RX)
Button3=1(TX)
Button4= 2(d4) for nodemcu V3 OR 10(SDD3)
Reset button=16(d0)
Led=2(d4) if you use GPIO2 for button don’t set a pin for LED
NodeMcu V3 LOLINExample Roller Shutter / Blinds nodemcu setting / 2 CHANNEL:
Relay1=5(d1) – Relay2=4(d2)
Button1=12(d6) – Button2=13(d7)
Reset button=16(d0) – Led=2(d4)
VIN pin which is 5dc from USB cable goes to Relay board’s VCC. JD-VCC jumper is on.Example 2 CHANNEL nodemcu setting:
Relay1=5(d1) – Relay2=4(d2)
Button1=12(d6) – Button2=13(d7)
Reset button=16(d0) – Led=2(d4)
download PDF http://homehome.app/support
translate.google.com

version 1.0

References

• HomeHome.App Apple HomeKit Google Home Smart Home Manuls
• Apple
• HomeHome.App - WEB UI

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>