Current 4228 Orbit IC LED Light eFlux Wave Pump User Guide
- June 17, 2024
- current
Table of Contents
Current 4228 Orbit IC LED Light eFlux Wave Pump
Thank you for getting In The LOOP!
For step-by-step video instructions, visit our website at www.current-
usa.com/videos.
WHAT’S INCLUDED
- Orbit IC LED Light
- LOOP Light Controller w/Mounting Clip
- Light Manifold (HUB) w/Mounting Clip
- 12V DC Power Supply
- Wireless Remote Control
- Remote IR Sensor (optional)
- eFlux Wave Pump, 660 gph w/Magnet Bracket
- Wave Pump Cable Protector
- Pump Manifold (HUB) w/Mounting Clip
- 24V DC Power Supply
- MicroUSB Communication Cable
- Cable Wraps
BEFORE INSTALLATION
- Follow ALL safety instructions and warnings included with this product.
- Find a clean, dry location to mount the LOOP controller, light & pump HUBs either under or outside your aquarium cabinet.
This product can receive command signals from the wireless remote in two locations:
- LOOP controller (sensor located on display front)
- Remote IR sensor
Decide if you want the LOOP controller to be located outside your cabinet to receive signals or inside the cabinet and use the remote IR sensor.
Ensure all electrical components are plugged into a GFCI. Keep lights, HUBs and controller dry and free of moisture, water and salt creep.
INSTALLATION
Install LED Light
Slide and adjust docking mounts, install LED Light on top of the aquarium
Install Wave Pump
- Wrap cable protector around internal pump cable
- Slide outer magnet from wave pump
- Clean mounting area from dirt or algae
- Position the pump in the tank, secure it with an outer magnet
TIP:
When removing the magnet from the pump, slide the magnet from the pump, do not
pull.
Mount HUBs and Controller
- Choose a clean, dry location for HUBs
- Screw mounting clips into the stand location
- Slide HUBs and LOOP controller into mounting clips
Connect
- Flip over for connection instructions
Connect the following:
-
Wave pump HUB to light HUB
(MicroUSB Cable Pump Port#1 to Light Port#4) -
LED light to light HUB
(Light cable to HUB Connection L1) -
LOOP controller to light HUB
(LOOP micro USB cable to Light HUB Port#1) -
Wave pump to pump HUB
(Wave pump cable to pump HUB Connection P1) -
Optional IR sensor to light HUB
(IR Sensor micro USB to Light HUB Port#2) -
12V DC power to light HUB
(12VDC cable to Light DC – L1 Connection) -
24V DC power to pump HUB
(24VDC cable to Pump DC – P1 Connection) -
Power supplies to the GFCI outlet
Note:
When connecting MicroUSB cables, be sure to push the plug in firmly.
Control
- Remove the remote battery tab
- Press ON, to ensure IR communication
- Program 24-hour clock (military time)
- Press SET CLOCK,
- Adjust time using HOUR+ and MINUTEPress ENTER/RESUME to finish
Pre-programmed Settings
- ON Time: 07:00 (7:00 am)
- OFF Time: 18:00 (6:00 pm)
- WEATHER: OFF
- Daylight: W90%,B,G,R-100%
- Dawn/Dusk: W10%,B80%,R50%,G20%
- Moonlight: B10%;R,G,W-0%
- Wave Pump#1: Stream, 100% Flow
- Wave Pump#2: Stream, 100% Flow
- Wave Pump#3: Stream, 100% Flow
To change pre-programmed settings, refer to the instruction manual included or visit our website at www.current-usa.com/videos.
WARNING!
Read the entire instruction manual to become familiar with the features of
this product before operating. Failure to operate the product correctly could
result in damage to the product, property or personal injury.
Please register this product
at www.current-usa.com.
For step-by-step instructions, visit our website at www.current- usa.com/videos.
Copyright© 2016 Current-USA Inc. LOOP® is a registered trademark of Current- USA. Multiple patents pending.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>