FISHER PAYKEL WB24SMB1-SET Warming Drawer User Manual

FISHER PAYKEL WB24SMB1-SET Warming Drawer

MINIMAL
WB24SMB1-SET
CONTEMPORARY
WB24SDB1-SET, WB30SDB1-SET & WB30SDX1-SET

INSTALLATION GUIDE

SAFETY AND WARNINGS

WARNING!

Tip Hazard
This product may tip. Keep children away and take care. Failure to follow this advice may result in injury.

• Drawer must be secured in place by supplied screws.
• Ensure there is a fixed shelf directly above the drawer if it is not installed under another product.

WARNING!

Cut Hazard

Failure to use caution could result in injury.

• Take care: some edges may be sharp.
• Do not put fingers in the drawer when closing.

WARNING!

Electric Shock Hazard
Failure to follow this advice may result in electrical shock or death.

• If the product is damaged, switch the appliance off and disconnect it from the mains to avoid possible electric shock.

WARNING!

Weight Hazard

Failure to follow this advice may result in damage or personal injury.

• Ensure the bottom shelf of the cabinetry can fully support the weight of combined appliances.

SAFETY AND WARNINGS

READ AND SAVE THIS GUIDE

WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety guides listed below. Read all the instructions before using the appliance.

Installation

• Please make this information available to the person installing the product.
• The appliance must be installed by a qualified installer, or Fisher & Paykel trained and supported service technician to avoid faulty electrical connection.
• Ensure the installation complies with all clearance requirements and applicable standards and regulations.
• When installed in combination with a companion product, the companion product can be placed directly onto the appliance. A built-in shelf at the base of the cabinetry must be able to support the weight of both products.
• Ensure the cabinetry is square and level and with correct dimensions.
• If installing the appliance directly underneath an oven, ensure you do not damage the oven’s lower trim. Fisher & Paykel does not accept any responsibility for any damage resulting from incorrect installation.
• Before installing the appliance, inspect for any signs of damage. Do not install or use damaged appliances.
• Be careful when stacking the appliances on top of each other to avoid damage to the appliances.

Electrical

• All connections for electrical power and earthing must be done by a qualified electrician and must comply with local codes and ordinances.
• Before installation, ensure that the voltage and frequency listed on the data plate corresponds with the household electrical supply.
• When combining with another appliance, ensure each appliance has its own power outlet. Avoid sharing the power point to prevent accidental switching off of the appliance.
• Ensure your appliance is properly grounded (earthed).
• Connect the drawer to a properly rated, protected and sized power supply circuit to avoid electrical overload.
• Do not use an extension cord or a portable electrical outlet device (e.g. multi-outlet outlet box) to connect the drawer to the power supply. Ensure the power supply cord is located so that it will not be stepped on, tripped over or otherwise subject to damage or stress.
• Ensure there is a switched outlet in an easily accessible area within 35 7/16” (900mm) of the centre rear of the product.

Servicing

• Do not repair or replace any part of the appliance unless specifically recommended in the user guide. All other servicing should be done by a Fisher & Paykel trained and supported service technician or qualified person.
• Always disconnect the power supply before doing any installation, maintenance or repair work, and cleaning.
• If the power supply cord is damaged, it must be replaced by a qualified electrician or Fisher & Paykel trained and supported service technician.

WARMING DRAWER MODELS

UNPACK YOUR PRODUCT

Remove the warming drawer and accessories box from the packaging. Recycle the materials that can be reused. Dispose packaging materials in accordance with local regulations on waste disposal.
Inspect the warming drawer for any signs of damage. Do not install the warming drawer if it has been damaged. If the product is damaged, contact your local Fisher & Paykel dealer.

ELECTRICAL SPECIFICATIONS

All electrical work must be done by a qualified electrician, or a Fisher & Paykel trained and supported service technician.

| WB24SMB1-SET
WB24SDB1-SET| WB30SDB1-SET
WB30SDX1-SET
---|---|---
Supply| 120 VAC, 60 Hz| 120 VAC, 60 Hz
Service| 10 amp circuit| 10 amp circuit
Maximum Power| 930 W| 930 W
Power outlet*| 3-prong grounding-type| 3-prong grounding-type
Power cord (total length)| 70 7/8″ (1800mm)| 70 7/8″ (1800mm)

• The power outlet must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.

PARTS SUPPLIED

TOOLS REQUIRED

PRODUCT DIMENSIONS – 24″ MODELS

PRODUCT DIMENSIONS| WB24SMB1-SET
WB24SDB1-SET
---|---
A Overall height| 5 1/2| 140
B Overall width| 23  7/16| 596
C Overall depth*†| 22  5/16| 567
D Height of chassis| 5 1/2| 140
E Width of chassis| 21 3/8| 543
F Depth of chassis**| 21  9/16| 547
G Height of drawer front panel| 5 3/8| 136
H Depth of drawer front panel and attachment flange†| 13/16| 20
I Depth of open drawer| 16  5/16| 414
J Height from bottom of chassis to bottom of drawer front panel| 16-Jan| 2

• Including drawer front panel and power plug.
  ** Including power plug
  † Excluding SS panel (Contemporary models).

PRODUCT WEIGHT| WB24SMB1-SET
WB24SDB1-SET
---|---
| LBS| KG
Total weight of drawer*| 48| 22

PRODUCT DIMENSIONS – 30″ MODELS

PRODUCT DIMENSIONS| WB30SDB1-SET
WB30SDX1-SET
---|---
| IN| MM
A Overall height| 10 11/16| 271
B Overall width| 29 15/16| 761
C Overall depth*†| 22 1/3| 567
D Height of chassis| 10 2/3| 271
E Width of chassis| 27 13/16| 707
F Depth of chassis**| 21 4/7| 547
G Height of drawer front panel| 10 1/2| 267
H Depth of drawer front panel and attachment flange| 13/16| 20
I Depth of open drawer| 16 1/2| 419
J Height from bottom of chassis to bottom of drawer panel| 11/16| 2

• Including drawer panel and power plug
  ** Including power plug
  † Excluding SS panel (Contemporary models).

PRODUCT WEIGHT
WB30SDB1-SET
WB30SDX1-SET

Total weight of drawer* 75LBS /  34KG

CABINETRY DIMENSIONS – 24″ MODELS

• The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.

• Depth of drawer front panel including attachment flange.

CABINETRY DIMENSIONS – 30″ MODELS

• The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.

• Depth of drawer front panel including attachment flan

INSTALLATION OPTIONS

STANDALONE INSTALLATION

This installation is suitable for Minimal, Contemporary & Professional Warming drawers. A fixed shelf must be installed above the warming drawer.

COMBINED WITH SINGLE OVEN

This installation combines 30″ Warming Drawer with 30″ Fisher & Paykel wall oven. The warming drawer can support the weight of the oven sitting directly on top.

COMBINED WITH COMPANION PRODUCT

This installation combines 24′ or 30″ Warming Drawer with 24″ or 30″ Fisher & Paykel companion product. The warming drawer can fully support the weight of the companion product sitting directly on top.

COMBINED WITH DOUBLE OVEN

This installation combines 30″ Warming Drawer with a 30″ Fisher & Paykel double oven. The warming drawer can fully support the weight of the double oven sitting directly on top.

TRIPLE STACK COMBINATION

This combination is suitable for 30″ Warming Drawers. A shelf is required above the oven to support the 30″ companion product. Ensure the bottom shelf can fully support the weight of all appliances.

INSTALLING THE DRAWER

TRIPLE STACK COMBINATION

This combination is suitable for 30″ Warming Drawers. A shelf is required above the oven to support the 30″ companion product. Ensure the bottom shelf can fully support the weight of all appliances.

INSTALLING THE DRAWER

INSTALL FRONT PANEL (SOLD SEPARATELY

ADJUSTING THE DEPTH

The depth of the front panel of the warming drawer can be adjusted to align with the surrounding cabinetry.

ADJUSTING THE HEIGHT

The front panel of the warming drawer can be adjusted vertically to align with the surrounding cabinetry.

INSTALLER CHECKLIST

IMPORTANT!
Read all installation instructions in this manual to see if the unit has been correctly installed.
Ensure that installation has been completed correctly before use.

Ensure that:

• the warming drawer is level and securely fitted to the cabinetry
• any internal packaging has been removed from the drawer
• the isolating switch is accessible by the customer
• the bottom shelf can fully support the total weight of the combined appliances

Test operation:

• Open the drawer.
• Press the POWER button to turn the warming drawer on.
• Shut the drawer
• After 5-10 minutes, open the drawer to feel the internal surfaces of drawer is slightly warmed
• Press the POWER button to turn the warming drawer off and shut the drawer

Complete and keep for safe reference:

Model.
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date _____

FISHERPAYKEL.COM

© Fisher & Paykel Appliances 2023. All rights reserved.
The models shown in this guide may not be available in all markets and are subject to change at any time.
The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product improvement, these specifications may change at any time.
For current details about model and specification availability in your country, please go to our website or contact your local Fisher & Paykel dealer

FAQ

Q: Can I install the warming drawer myself?

A: The appliance must be installed by a qualified installer, or Fisher & Paykel trained and supported service technician to avoid faulty electrical connection.

Q: What should I do if the power supply cord is damaged?

A: If the power supply cord is damaged, it must be replaced by a qualified electrician or Fisher & Paykel trained and supported service technician.

Q: How should I dispose of the packaging materials?

A: Dispose of the packaging materials in accordance with local regulations on waste disposal.

Q: What should I do if the warming drawer is damaged?

A: Do not install the warming drawer if it has been damaged.
Contact your local Fisher & Paykel dealer for assistance.

References

• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA
• Shop Luxury Kitchen & Home Appliances | Fisher & Paykel USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>