dyson AM04 Recalls Bladeless Portable Electric Heaters Instruction Manual

: June 17, 2024
: dyson

**dyson AM04 Recalls Bladeless Portable Electric Heaters Instruction Manual

**

ASSEMBLY

Remote control docks magnetically
ASSEMBLY

Power on

On first use, the heater will default to a temperature 1°C higher than the current room temperature. Thereafter, the heater will remember the last target temperature set.

Thermostat control

Select the desired room temperature. Pressing red increases the target temperature, blue decreases it. The heater will not operate unless the target temperature is above the room temperature.

Airflow speed control

To change the airflow speed press the airflow speed control button. The digital display will show the new speed; after 3 seconds it will change back to the target temperature.

Oscillation control

To start the heater oscillating, press the oscillation control button. To stop the heater oscillating, press it again. The heater will not oscillate when the control buttons are pressed.

Heating mode

**Spot heat

Select a low flow of air.**

**Whole room

Select a high flow of air.

For best results turn on the oscillation control.**

Cool air mode

Press the blue thermostat control button to change the target temperature to 0°C. The power button light will change from red to blue. To adjust the airflow speed use the airflow speed control.

To return to heating mode

Press the red thermostat control button until the digital display shows the desired target temperature. The power button light For best results turn on the oscillation control. will change from blue to red.

Tilt function

Carefully hold the base and the top of the air loop amplifier. Tilt forward backwards for the required airflow angle.

Power and remote control*

*Remote control with select models only.

Remote control docks magnetically
Attach remote control to top of heater with the buttons facing down.

To operate, point remote control toward the front of the base.

Clearing blockages

Ensure the heater is unplugged and has been allowed to cool. Look for blockages in the air inlet holes and in the small aperture inside the air loop amplifier. Use a soft brush to remove debris

caution: hot when in use

This heater is hot when in use and for a short period after use. Do not let bare skin touch hot surfaces. If children are present, consider positioning the heater out of their reach.

Cleaning

Unplug from the mains electricity supply. Allow to cool for 1 to 2 hours before cleaning if the heater has been in use. To clean, wipe with a dry or damp cloth. Do not use detergents or polishes.

battery replacement

A blue light on the heater will flash when the remote’s buttons are pressed. If the blue light stops flashing, replace the remote’s battery.

Battery type CR 2032.

Press the end of the remote to release the battery. Remote control with selected models only

IMPORTANT SAFETY INSTRUCTIONS

BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND AUTIONARY MARKINGS IN THIS MANUAL AND ON THE APPLIANCE
When using an electrical appliance, basic precautions should always be followed, including the following:

WARNING
THE HEATER AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS

Pacemakers and defibrillators may be affected by strong magnetic fields. If you or someone in your household has a pacemaker or defibrillator, avoid placing the remote control in a pocket or near to the device.
Credit cards and electronic storage media may also be affected by magnets and should be kept away from the remote control and the top of the heater.

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY

This heater is hot when in use and for a short period after use. To avoid burns, do not let bare skin touch hot surfaces. When moving the heater hold it by the base, not the air loop amplifier.
Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains, at least 0.9m (3 feet) from the front of the heater and keep them away from the sides and rear when the heater is plugged in.
Extreme caution is necessary when any heater is used by or near children or infirm persons and whenever the heater is left operating and unattended.
Do not allow to be used as a toy. Close attention is necessary when used by or near young children. Children should be supervised to ensure that they do not play with the heater or remote control.
This heater and remote control are not intended for use by young children or infirm persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction by a responsible person concerning use of the heater to ensure that they can use it safely.
The base must be fitted securely before operating. Do not dismantle or use without the base fitted.
Suitable for dry locations ONLY. Do not use outdoors or on wet surfaces. Do not use in bathrooms, laundry areas and similar indoor locations. Never locate the heater where it may fall into a bath or other water container. Do not use or store where it may get wet or in the immediate surroundings of a bath, a shower, or a swimming pool.
A heater has hot parts inside. Do not use it in areas where petrol, paint, or flammable liquids are used or stored or where their vapors are present. Do not use in conjunction with or directly next to an air freshener or similar products.
Do not locate directly below a mains electricity supply socket.
Always plug directly into a wall socket. Never use with an extension cable as overloading may result in the cable overheating and catching fire.
Do not handle any part of the plug or heater with wet hands.
Do not unplug by pulling on the cable. To unplug, grasp the plug, not the cable.
Do not stretch the cable or place the cable under strain. Do not run the cable under carpeting. Do not cover the cable with throw rugs, runners, or similar coverings. Do not route the cable under furniture or appliances. To avoid a tripping hazard arrange the cable away from traffic area so that it will not be tripped over.
Do not use with a damaged cable or plug. If the supply cable is damaged it must be replaced by Dyson or its service agent or similarly qualified persons in order to avoid a hazard.
To disconnect the heater, turn the controls off, then remove the plug from the socket. Always unplug the heater when not in use.
Do not use if the heater malfunctions or has been dropped or damaged in any manner. Contact the Dyson Helpline or return to an authorised service facility for examination and/or repair.
To prevent a possible fire, do not use with any opening or exhaust blocked, and keep free of dust, lint, hair, and anything that may reduce airflow. Do not put any object into the inlet grill or the exhaust opening as this may cause an electric shock or fire, or damage the heater.
Do not use on soft surfaces, such as a bed, where openings may become locked.
Use only as described in this Dyson Operating Manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
In order to avoid overheating and fire hazard, do not cover the heater.
Choking hazard: the remote control unit contains a small battery. Keep the remote control away from children and do not swallow the battery. If the battery is swallowed seek medical advice at once.
The heater should be positioned so the airflow is directed away from any walls or room corners.

IMPORTANT SAFETY FEATURES

For your safety this heater is fitted with automatic cut-out switches that operate if the heater tips over or overheats. If the switches operate, unplug the heater and allow it to cool. Before restarting the heater check and clear any blockages and ensure the heater is on a solid level surface.

READ AND SAVE THESE INSTRUCTIONS

THIS DYSON APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY

Do not pull on the cable.

Do not store near heat sources.

Do not use near open flames.

Do not carry by the air loop amplifier. The air loop amplifier is not a handle.
![air loop

amplifier](https://manuals.plus/wp- content/uploads/2024/02/Screenshot_24-125.png)

In order to avoid overheating and fire hazard, do not cover the heater

USING YOUR DYSON HEATER
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON OPERATING MANUAL BEFORE PROCEEDING.

OPERATION

The base must be fitted securely before operating. Do not dismantle or use without the base fitted.
The heater will not operate unless the target temperature is above the
room temperature.
The heater will not oscillate when the control buttons are pressed.
For your safety this heater is fitted with automatic cut-out switches that operate if the heater tips over or overheats. If the switches operate, unplug the heater and allow it to cool. Before restarting the heater check and clear any blockages and ensure the heater is on a solid level surface.
If power is interrupted an E1 failure message will be displayed. The heater will need to be turned off and then on again. If the problem persists, call the
Dyson Helpline.
Do not carry out any maintenance or repair work other than that shown in this Dyson Operating Manual, or advised by the Dyson Helpline.
Do not lubricate any part of this heater

TILT FUNCTION
Carefully hold the base and the top of the air loop amplifier. Tilt forward or awkward for the required airflow angle.

CLEANING

Turn the heater into stand by mode/off.
Unplug from the mains electricity supply.
Allow to cool for 1 to 2 hours before cleaning if the heater has been in use.
To clean, wipe with a dry or damp cloth only.
Do not use detergents or polishes to clean the heater

STORAGE

When not in use, unplug from the mains electricity supply.
Store the heater in a dry location and arrange the cable away from the traffic
area so that it will not be tripped over or damaged.

BATTERY REPLACEMENT

Caution :

Turn the heater into stand by mode and unplug from the mains electricity supply before replacing the battery.
Ensure the polarity is correct when installing the battery.
Do not attempt to dismantle or charge the battery. Keep away from fire.
Follow battery manufacturers’ instructions when installing the new battery (battery type CR 2032).

TROUBLESHOOTING

Remember: Always unplug from the mains electricity supply before inspecting for problems.
If the heater will not operate, first check the mains socket has electricity supply and that the plug is properly inserted into the socket.
If you are still experiencing problems, call the Dyson Helpline.
For additional online help visit:
UK : www.dyson.co.uk/AM04gettingstarted
ROI : www.dyson.ie/AM04gettingstarted

GUARANTEE TERMS & CONDITIONS DYSON CUSTOMER CARE

THANK YOU FOR CHOOSING TO BUY A DYSON APPLIANCE

After registering your free 2 year guarantee, your Dyson appliance will be covered for parts and labor for 2 years from the date of purchase, subject to the terms of the guarantee.
If you have any questions about your Dyson appliance, call the Dyson Helpline with your serial number and details of where/when you bought the appliance. Most questions can be solved over the phone by one of our trained Dyson Helpline staff.
Alternatively, visit www.dyson.co.uk/support for online help, general tips and useful information about Dyson.
If your Dyson appliance needs a service, call the Dyson Helpline so we can discuss the available options. If your Dyson appliance is under guarantee, and the repair is covered, it will be repaired at no cost.
Your serial number can be found on your rating plate which is on the base of the appliance.

PLEASE REGISTER AS A DYSON APPLIANCE OWNER
To help us ensure you receive prompt and efficient service, please register as a Dyson appliance owner. There are three ways to do this:

Online at www.dyson.co.uk/register
Telephone the Dyson Helpline.
Complete the enclosed form and post it to us.

This will confirm ownership of your Dyson appliance in the event of an insurance
loss, and enable us to contact you if necessary.

LIMITED 2 YEAR GUARANTEE

TERMS AND CONDITIONS OF THE DYSON 2 YEAR LIMITED GUARANTEE

WHAT IS COVERED

The repair or replacement of your Dyson appliance (at Dyson’s discretion) if it is found to be defective due to faulty materials, workmanship or function within 2 years of purchase or delivery (if any part is no longer available or out of manufacture Dyson will replace it with a functional replacement part).
Use of the Dyson appliance in the country of purchase only

WHAT IS NOT COVERED

Dyson does not guarantee the repair or replacement of a product as a result of

Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or handling of the appliance which is not in accordance with the Dyson Operating Manual.
Use of the appliance for anything other than normal domestic household purposes.
Use of parts not assembled or installed in accordance with the instructions of Dyson.
Use of parts and accessories which are not genuine Dyson components.
Faulty installation (except where installed by Dyson).
Repairs or alterations carried out by parties other than Dyson or its authorised agents.
Blockages – please refer to the Dyson Operating Manual for details of how to
look for and clear blockages.
Normal wear and tear, such as the battery.
If you are in any doubt as to what is covered by your guarantee, please contact Dyson

SUMMARY OF COVER

The guarantee becomes effective at the date of purchase (or the date of delivery if this is later).
You must provide proof of (both the original and any subsequent) delivery/ purchase before any work can be carried out on your Dyson appliance. Without this proof, any work carried out will be chargeable. Keep your receipt or delivery note.
All work will be carried out by Dyson or its authorised agents.
Any parts which are replaced will become the property of Dyson.
The repair or replacement of your Dyson appliance under guarantee will not extend the period of guarantee.
The guarantee provides benefits which are additional to and do not affect your statutory rights as a consumer

ABOUT YOUR PRIVACY

Your information will be held by Dyson Limited and its agents for promotional, marketing and servicing purposes.
If your personal details change, if you change your mind about any of your marketing preferences or if you have any queries about how we use your information, please contact Dyson Limited.
For more information on how we protect your privacy, please see our privacy
policy on the Dyson website.

DISPOSAL INFORMATION

Dyson products are made from high grade recyclable materials. Please dispose of this product responsibly and recycle where possible.

PRODUCT INFORMATION

Please note: Small details may vary from those shown. Net weight: 2.57kg

Note your serial number for future reference.
Bar Coad

This illustration is for example purposes only

DYSON CONTACT DETAILS

Website: www.dyson.com/support
UK :
Dyson Helpline: UK: 0800 298 0298
Open 7am–10pm. 7 days a week.
Email : askdyson@dyson.co.uk
Address : Dyson Limited, Tetbury Hill, Amesbury, Wiltshire SN16 0RP England.
ROI :
Dyson Helpline: ROI: 01 475 7109
Open 7am–10pm. 7 days a week.
Email : askdyson@dyson.com
Address : Unit 10, Grants Lane, Greenough Business Park, Rathcoole, Dublin 24.

As a Dyson appliance owner, you can hear about Dyson inventions, services and products before anyone else. If it’s okay to contact you, please let us know how we may do this.

By mail Yes  No 
By phone Yes  No 
By email Yes  No 
By text message Yes  No 

We sometimes ask other companies (such as market researchers) to contact owners on our behalf. We do this to get feedback on ideas or ask you to try new products and services. Would this be okay?

Yes  No 

3 EASY WAYS TO REGISTER YOUR FREE 2 YEAR GUARANTEE

REGISTER
ONLINE
Visit our website to register your full parts and labor guarantee online.
www.dyson.com/register

REGISTER BY PHONE
Call our dedicated Helpline.
Open 7am-10pm.
7 days a week.
UK 0800 298 0298
ROI 01 475 7109

REGISTER BY MAIL
Complete and return the form to Dyson in the envelope supplied.