LABGEAR HDMX60K Mini HDMI 60m Extender Kit User Guide

HDMX60K
Mini HDMI 60m Extender Kit
over single CAT6/7
User Guide

Introduction

This HDMI extender kit is designed to extends a 1080p HDMI signal up to 60m over asingle CAT6 network cable.

Safety Warnings

1. Be clear which unit is the HDMI to RJ45 sender and which is the RJ45 to HDMI receiver before installation.
2.  Always switch off sender and receiver before connecting or disconnecting devices, make your connections and then switch back on.
3. Use aDCSV/1A power supply only. If you are using power supplies other than those supplied in the kit make sure specification is correct (DC5V/1A).

General Warnings

• Do ot drop, tamper, disassemble o attempt to repair any part of the kit yourself.
• Do notimmerse any part of the kit in water or expose it to wet conditions.
• Do not expose any part of the kit to fire or any heat source.
• Do not dispose of any part of the kit in your household waste.

Box Confents

Installation Requirements

1. HDMiI source device(DVD, Blu-ray, computer graphics card, PS3, HD security/monitoring equipment etc).
2. HDMI display device like SDTV, HDTV, projector with HDMI port.
3. UTP/STP cat6/6A/7 cable, follow standard IEEE-568B.

Features and Connections

HDMI to RJ45 sender

1. HDMI out socket (loop through)
2. HDMI signal indicator LED Stays lit when an HDMI signal is being received, flashes when there is no signal input.
3. HDMIIN socket
4. IR signal output connects to sender extension cable
5. RJ45 OUT socket
6. Reset button
7. DC5V power supply input

RJ45 to HDMI to receiver

1. Reset
2. RJ45 IN socket
3. RJ45 indicator LED Stays lit when an HDMI signal is being received, flashes when there is no signal input.
4. DC5V power supply input
5. HDMI OUT socket
6. IR signal input to connects to IR receiver extension cable

Installation

1. CAT6 Wiring Connections
Following IEEE-568B wiring standard :

1. Orange/white
2. Orange
3. Green/white
4. Blue
5. Blue/white
6. Green
7. Brown/white
8. Brown

2. System Connections

Connection Sequence

1. Connect HDMI source device to TX HDMIIN.
   Connect HDTV HDMI IN to TX HDMI OUT.

2. Connect TX CAT6 OUT to RX CAT6 IN.

3. Connect HDTV HDMIIN to RX HDMI OUT

4. Switch on extender and all devices.

Troubleshooting

Q: No image output or audio and video display is not normal?

A: 1) Press RX “RESET” button to reset the device. 2) Reconnect with a shorter network cable.

Q: RX “LINK” LED is flashing all the time?

A: 1) Make sure network cable wiring complies with IEEE- 568B Standard. 2) Check whether TX has HDMI signal input. 3) Reset TX & RX and reconnect.

Q: RX “LINK” LED light is lit but no image appears?

A: 1) Press the RX “RESET” button to reset the device. 2) Check HDMI to TV cable connections. 3) Make sure CAT6 or CAT7 network cable is being used.

Specifications

720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
Network Cable Requirement| Low resistance and consumption oxygen-free copper core (CAT6, CAT6A, CAT7)
Maximum distance| 60m @ 1080p over CAT6/6A/7
IR remote control| Supports 20-60KHz wide frequency IR remote control
Audio Support| Dolby TrueHD or DTS-HD Master Audio
Power supplies| 2 x 5V/1A DC
Power Consumption| Sender <3W, Receiver <2W
Wall Mountable| Yes
Dimensions| 71.6 (L) x 66.6 (W) x 24.8mm (H)
Weight| 83g and 80.6g
Working Temperature| 0-60° C

Technical Support

For further information, please contact:
Customer Careline: 08457 573 479
Local ate: UK Only
‘www.labgear.co.uk

Waste electrical and electronic products must not be disposed of with household wasle.
Please recycle where faciliies exist.
Check with your Local Authority for recycling advice.
© Labgear 2015. v1 MK42 ONX

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>