Labgear LCOM1 Combo HD Satellite and Terrestrial Receiver User Guide

Labgear LCOM1 Combo HD Satellite and Terrestrial Receiver

Product Information

• The LCOM1 Combo HD Satellite & Terrestrial Receiver is a versatile receiver that supports H.265 and MPEG-4/AVC video formats. It is compatible with satellite and terrestrial signals, including S/S2/S2X and T/T2 standards. The receiver also features DiSEqC 1.0, 1.1, and 1.2 support for convenient satellite dish control. With 1080p Full HD resolution, it delivers high-quality video output.
• The receiver is equipped with various safety features to protect against spikes, surges, electric shock, and lightning strikes. It is recommended to use surge protection systems to extend the life of the equipment.
• For recording purposes, the LCOM1 supports external hard disk drives (HDDs) and flash memories (Pen drives). However, the compatibility and correct operation of the recording function depend on the type of memory connected. USB memory media must support the USB 2.0 standard for proper functionality.
• Important warnings include not disconnecting the USB device during recording or playback to avoid damage to the receiver and memory, as well as not touching the working device or USB connector with wet hands to prevent electric shock.
• The receiver also offers features such as audio and image file playback and storage, as well as database backup.

Product Usage Instructions

To get started with the LCOM1 Combo HD Satellite & Terrestrial Receiver, follow these steps:

1. Ensure that your equipment is protected against spikes, surges, and lightning strikes using surge protection systems.
2. Connect the receiver to your satellite dish or terrestrial antenna following the provided instructions.
3. Insert 2 AAA Alkaline batteries into the remote control, observing the correct polarity.
4. Connect the receiver to your TV using the provided HDMI cable.
5. Plug the 12V1A power adaptor into a power outlet and connect it to the receiver.
6. Turn on the receiver using the POWER button on the remote control.
7. Use the remote control to navigate the main menu and access various functions.
8. To access specific functions directly, use the colored function keys on the remote control (RED, GREEN, YELLOW, BLUE).
9. Use the cursor keys (UP/DOWN) to change channels and navigate through menus.
10. Press OK to confirm selections or entries, and to display the channel list.
11. Adjust the volume using the VOL+/- buttons.
12. Press MUTE to mute or restore audio output.
13. Use the PLAY/PAUSE, STOP, PREV, NEXT buttons for media playback control.
14. Press SAT to enter or exit satellite mode.
15. Press SUBTITLE to select subtitle language.
16. Press TEXT to display Teletext information.
17. Use the AUDIO button to select an audio language or audio mode.
18. Press MENU to access the main menu.
19. Press INFO to display additional channel information.
20. Use the EPG button to turn on/off the Electronic Program Guide.
21. Press EXIT to exit the current menu or return to the previous menu.
22. Press REC to record a selected program.
23. Use the numeric buttons (0-9) for entering numbers or making selections.
24. Press GOTO to switch between Satellite and TP mode.
25. Press TV/RADIO to switch between TV and Radio functions.
26. Use the Pg+/- buttons for page up/down navigation.
27. Press FAV to access the Favorite menu.

Make sure to follow all safety precautions and guidelines provided in the user guide to ensure proper and safe usage of the LCOM1 Combo HD Satellite & Terrestrial Receiver

General Safety

• This product is for indoor use only, do not expose to rain, moisture, very high and low temperatures, strong magnetic fields and dusty environments
• Disconnect power to the units before cleaning. Do not use abrasives or solvents to clean the surface of the unit, wipe with a clean soft cloth
• Do not disassemble any of the units in this kit they contain no user serviceable parts.
• Refer servicing to qualified personnel only
• This device should be operated using only the AC/DC adaptor supplied with it.
• Unplug the adaptor from the mains if the unit is not going to be used for a while
• Install the units in locations with adequate ventilation.
• This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the life of your equipment.

Advice on Recording USB Media
The LCOM1 supports recording and playback on external hard disk drives (HDDs) and flash memories (Pen drives). In all instances, the correct operation of the recording function depends on the type of memory connected. Please read the following advice and limitations.

1. All USB memory media connected must support the USB 2.0 standard.
   To ensure stable recording and playback, always use high speed drives recommended for recording
   HD video. Slower hard drives and flash memory sticks may not function properly, and have problems with recording (image jitters), or just not function at all.

2. Drives must be formatted with one basic NTFS or FAT32 partition to function properly (we recommend using the NTFS format). If you do not have such a format, prepare the disk on your computer before connecting it to the receiver.

3. Highly fragmented or used memories may also not operate smoothly or correctly.

4. External hard disk drives should be connected to a suitable power supply, since the built-in USB ports are unable to provide sufficient power.

Warning

1. Do not disconnect the USB device from the receiver during recording or playback. As this can cause damage to the receiver and/or memory, and to the recorded data.
2. To prevent the risk of an electric shock and permanent damage to the receiver!
   Do not touch the working device (and in particular the USB connector) with wet hands.

Features

• Receives High-Definition satellite and terrestrial TV
• PAL upscaling up to 720p or 1080p resolution
• Supports teletext & multilingual subtitles
• Simultaneously watch Terrestrial while recording Satellite content or watch Satellite while recording Terrestrial
• Full compliance with DVB-S/S2X and DVB-T/T2 digital TV reception standards
• Support for HDTV/SDTV: MPEG-2/MPEG-4/H.265 decoding
• Support for 480i/480p/576i/576p/720p/1080i/1080p
• User friendly auto search function
• Storage capacity for storing up to 2000 transponders and 4000 channels
• Input frequency: Terrestrial 470 – 860MHz, Satellite 950MHz – 2150MHz
• Reception for SCPC/MCPC.C/Kuband LNBs.
• Supports DiSEqC 1.0, 1.1, 1.2 USALS motorised dish systems
• 7 Day EPG for terrestrial channels and a “now and next” for satellite channels
• Favourite channel store, edit and parental lock functions
• Adjustable aspect ratio 4:3 Pan & Scan or 16:9 Widescreen modes
• Twin USB 2.0 ports for: PVR and Timeshift recordings from satellite and terrestrial inputs / Multimedia video, audio, image file playback & storage / Database backup

Box contents

• 1x Combo Receiver
• 1x Remote Control
• 1x 12V?1A Power Adaptor
• 2x AAA Batteries
• 1x 1m HDMI Cable
• 1x User Guide

Basic Operations

The main menu simplifies operation of the receiver. All of the receiver functions are displayed in the menus and can be controlled by using of a small number of keys, and certain keys on the remote control allow direct access to specific functions.

Remote Control

Installing Batteries in the Remote Control
Insert the batteries supplied (2x AAA Alkaline) into the remote taking care to observe the polarity indicated in the battery compartment. When replacing batteries do not mix old and new batteries, or batteries of different types . Back Panel Connections

Connecting a Satellite Dish LNB to the LCOM1
For satellite signal reception you will need a satellite dish fitted with a suitable LNB connected to the “LNB IN” port on the LCOM1 back panel. The satellite dish needs to be positioned in line of sight of the satellite(s) from which you wish to receive signals. Make sure there are no obstructions in the way. Accurate positioning of the dish and LNB is critical for reception and it is recommended that you contact an experienced installer if you need any help.

Satellite Dish Alignment Settings

• There are a number of online satellite finder apps for smartphones which can be used to help align your dish. Finder apps vary so we suggest you use them in conjunction with a satellite meter and a compass. You can also obtain accurate settings from the website: www.dishpointer.com. Enter your location and select a satellite the website will give the precise settings that you will require to align to the satellite.
• Labgear stock a range of TV and Satellite signal finders and meters, for more information please visit https://labgear.co.uk/product-category/meters-testers/tv-sat-signal-meters

Aligning the Satellite Dish
Three settings are required. Initially use the settings you have obtained using one of the methods described in the paragraph above :

1. Dish elevation – usually close to vertical
2. Azimuth angle – this is the compass bearing required and varies depending on your location in the country.
3. Polarisation (Skew) angle – this is the angle at which the LNB needs to be rotated in its mount.

Motorised Satellite Dish systems

• The LCOM1 is fully compatible with USALS positioners which should be installed between the mast and the dish and connected to the “LNB IN” port. The USALS function considerably simplifies the setup. Once your local geographical coordinates are entered the positioner turns the dish to align automatically with the selected satellite. When the first satellite signal is locked on, you should fine tune the antenna’s elevation and azimuth settings in order to optimize signal reception.
• Once you have tuned in the first satellite, other satellite positions will be remembered automatically as long as the values have been entered accurately.
• The LCOM1 is also compatible with DiSEqC 1.2 positioners.
• For additional information on positioners please check the manufacturer’s instruction manual and website support.

Connecting a terrestrial aerial
For DVB-T/T2 terrestrial digital TV reception use a suitable outdoor wideband aerial. Make sure the aerial is in good condition and suitable for reception in your area. You can use the postcode checker on the Wolfbane website http://www.wolfbane.net/cgi-bin/tvd.exe? to check suitability and also to give you a bearing for your local transmitter.

For best reception ensure that:

1. The coaxial downlead from the aerial uses good quality cable and is positioned away from radio transmitting devices, metal objects and heat sources.
2. The antenna is installed at as high an elevation as practical pointed in the direction of the nearest TV broadcast transmitter
3. Check your neighbour’s aerial or look online for information on local transmitter locations and bearings. You can also use a signal strength meter (not included) to align your aerial for optimum reception.
4. Try and ensure there are no obstructions in the line of sight between the antenna and transmitter.

Only use an indoor aerial if you are close to a transmitter and receive a strong signal. Connect the selected aerial to the “ANT IN” port on the back panel of the LCOM1.

Video and Audio output
To connect a TV or other display equipment use an HDMI cable connected to the HDMI port for high definition video and audio output. You can make a separate digital audio connection to digital Hi-Fi systems via the coaxial port.

Connecting external memory
The receiver supports all types of hard disk drives and USB flash drives. See the ìAdvice on Recording USB Mediaî on page 2. Connection can be made via either of the USB ports on the back or the side of the receiver. Connected drives can be used for recording satellite and TV programmes and for playback of these recordings as well as playback of a wide range of video, music and image files stored on USB media,

Network connection
The RJ45 port allows you to connect the receiver to a local network using a patch lead connected to a router. Alternatively network connections can be made using a USB Wi-Fi dongle.

Navigating menus
Some keys on the remote allow direct access to functions of the receiver. Such as MENU and OK. Some keys are multi-functional and their operation depends on the type of device selected by the user. See below some of the device functions available through the user menu.

1. The up/down arrow keys on remote move the cursor up and down the menu.
2.  The left/right arrow keys on the remote are move the cursor left and right, or to go to submenus.
3. The OK key is used to enter submenus.
4. The EXIT key is used to exit menus or functions.
5. In a submenu, press the OK key to confirm a selection; a green background indicates an active function.

Main menu

Press the MENU key display the main menu and access the following menus:

1. Installation
2. Channel List
3. System
4. Media Centre
5. YouTube

Installation

This menu sets satellite/terrestrial/cable search parameters and to search channels for them.

Satellite list
This menu sets satellite/terrestrial/cable search parameters and allows you to search for channels.

Satellite
Use the keys to move up and down the list and press OK to select a satellite(s). Selected satellites will be marked with a tick. If you have a standard static satellite dish it will usually just be a single satellite.

1. Then press the blue key to scan.
   If one satellite is marked for scan, it will be a single satellite search, if multiple satellites are marked, it will be a multi satellite search.

2. Press green key to edit a satellite

3.  Press yellow key to delete a satellite.

4. Press the red key to add a satellite not listed.

Satellite search
In this menu you can search channels from one selected satellite.

1. Press key to select FTA (Free to Air) only, key to select Yes/No.

2.  Press / key to select Scan Channel, /key to select TV + Radio/TV Channel/ Radio Channel.

3. Press key to select Search Mode, key to select Blind Scan (recommended)/Full Scan.

4. Press key to select Search, and press OK key to start.

5. Blind Scan is an automatic search for all available satellite frequencies, which are then scanned in turn for channels.

6. Full Scan – searches according to the receivers pre-loaded TP list. Frequency by frequency.

For satellite systems with motorised dishes you can search multiple satellites .

• When the Blind Scan is complete press the OK key to save the list of channels found.
• The screen will show the first channel in the list.
• Press the OK key again to see the list of channels found.
• The full list of channels found can be viewed and edited in the TV Channel List menu, see page 9.

Terrestrial channel search
Open the Installation menu and select the Terrestrial option and press OK to open the Channel Search menu.

Press key to select Auto Search (recommended) press OK key to start.

1. Use and keys to select your country.
2. Use and keys to select FTA (Free to Air Channels) Only, On option.
3. Press key to select Search, and press OK key to start.

Auto Search – Recommended
Searches all available terrestrial channels automatically – the receiver searches frequency by frequency according to the search mode saved for the Country you have selected.

Manual Search

• You can search for channels manually if channels that should be available locally do not appear in the terrestrial channel list – the receiver searches the channel frequency choose in the manual search menu.
• When the Auto Search is complete press the OK key to save the list of channels found.
• The screen will show the first channel in the list.
• Press the OK key again to see the list of channels found.
• The full list of channels found can be viewed and edited in the TV Channel List.
  

Channel List
In the Main menu select Channel List & press OK. Press OK again to enter the TV Channel List submenu.

TV Channel List

• Press the SAT key key to scroll to < All > press OK and select from All, a satellite list (by name) / Terrestrial channel list and all the Favourite categories with saved channels.

Editing the list of TV channels.
Use the keys to go to a channel then press the FAV key or one of the colour keys on the remote control to mark the channel.

1. FAV: Highlight a TV channel press the FAV key to open the Favourites list, use the keys to select a category and press OK twice. Press EXIT to save. Favourite selections are marked with a heart symbol.

2. LOCK: Press the RED key to lock a selected channel. The LOCK option is password protected, enter the default password “0000”. Press EXIT to save. Locked selections are marked with a padlock symbol.

3. SKIP: Press the GREEN key to select a TV channel you want to Skip it will be marked with a return arrow symbol. Exit to save selections.

4. MOVE: Press the YELLOW key, use the keys to move the highlight bar to the TV channel(s) you want to move and press OK to mark, then use the
   keys to move the highlight bar to the position you want move the channel(s) to and press the INFO key. Finally, press the EXIT key twice to exit the TV channel list menu and save the new list order.

5. Edit (Sort/Edit Name/Delete):
   To SORT press the BLUE key first then press the RED key to see sort options select the option you want and press OK, press the EXIT key to save new list order.

• To EDIT a selected channel name, press the BLUE key, now then the GREEN key, follow the on screen instructions to rename the channel, press the YELLOW key then the EXIT key to save.
• To DELETE a channel, press the BLUE key, use the keys to select a channel, press the BLUE key again then press the EXIT key to complete the
  deletion and save the change.

Radio Channel List
In the Channel List menu use the keys then press the OK key to open the Radio Channel List. To EDIT use the same actions as used with the TV Channel List.

Favourite Menu
The Favourite function lets you recall by genre any channels you have saved to categories in the TV Channel List: Movies, News, Music, Sports, Childrens, Education, Social and Culture. In the Favourite menu you can edit the category titles.

System Menu

In the System menu you can make network configurations (once you are connected to a network). Set the OS language, local time and a parental lock. Set the optimum output resolution to suit your display. Control receiver software updates via USB and if necessary perform a factory reset.

Media Centre Menu

• The Media Centre menu lets you playback media files stored on USB Hard Drives and USB Flash/Pen Drives attached to the USB ports on the side and back of the LCOM1 receiver.

• The MUSIC submenu lets you playback stored music files in MP3 and other popular formats.

• The PICTURE submenu lets you playback stored photos and images stored in jpeg and bmp format files in MP3 and other popular formats.

• The MOVIE submenu lets you playback stored avi, mkv, mpeg, ts, mp4 etc. format videos/movies. Please Note: Not all files with these extensions are playable – some files may have unsupported codecs or settings.

• The RECORD MANAGER submenu lists the TV programmes you record. The list is fully editable and recordings can be locked or deleted.

• The HDD INFORMATION submenu displays information about the Hard Drives connected to the USB ports.

• The DVR CONFIGURATION submenu lets you configure a partition for Timeshift recording.

• The TS RECORD submenu lets you set the Transponder to make Transport Stream recordings.
  Please Note : This is only available when a hard disk or USB disk is connected to the receiver.

• The GAME submenu lets you play Othello or Tetris.

Important Remote Control Functions

Live Programme Recording
This function is only available when a suitable Hard Drive is connected to one of the USB ports.

1. Select a channel and press the REC button to record the channel selected.
2.  The information bar indicates which program you are recording and viewing.
3. In order to terminate recording, press the STOP button.
4. Keep in mind that during recording, the information bar may be hidden by means of the EXIT button. In order to restore the bar, press REC again.

Twin Tuner

• The receiver has separate tuners for the reception of satellite (DVB-S/S2) and terrestrial (DVB-T/T2) signals.
• This allows you to watch a satellite channel broadcast whilst recording a terrestrial channel and vice versa – watch a terrestrial channel while recording a satellite channel.

EPG – Electronic Programme Guide

• The receiver features a 7 Day EPG for terrestrial channels and a “now and next” EPG for satellite channels.
• Press the EPG key to display the guide.
• Use the and keys to view programmes in the EPG. Using the Timer option you can schedule future viewings and recordings of your favourite programmes automatically in advance. To enter the Timer Setting submenu press the GREEN key on the remote. All the programme timing details are shown scroll down to highlight Mode and
• press the keys to select the “View” or “Record” option. To record you will need to ensure a suitable USB drive is connected.

Timer Setting – List of Recordings

• You can review all the recordings scheduled by opening the Channel List menu and then opening the Timer
• Setting menu which lists the scheduled recordings.
• To see the details or to edit or cancel a recording highlight the recording and press OK to open the
• Timer Setting submenu. again.

Playing Back Recordings
To playback recordings open the Record Manager submenu in the Media Centre menu available recordings are listed.

Editing Recordings

• In the Record Manager use the keys to select a recording press OK to play. You can also Lock, Delete and Rename a recording.
• If your hard drive has more than one partition you can also change partition.

PAUSE – Timeshift Recording
If your viewing is interrupted or you need to stop viewing but don’t want to miss the action:

1. Press PAUSE
2. The time elapsed bar will now be visible on the screen and the programme will freeze.
3. Press the PLAY ; button in order to resume viewing from the pause point. The receiver will continue to record the same channel while you watch the previously broadcast program. During timeshift playback, press the EXIT button to hide the information bar. Press the PAUSE  /i INFO key again to restore the bar.

To scroll through currently stored timeshift recordings:

1. Press PAUSE to switch on timeshift mode.
2. Use the Fast forward and Rewind keys to navigate through the timeshift buffer, press PLAY to view.
3. Use the keys to move the playback start marker position and press OK to play.
4. To switch off the Timeshift mode press the STOP or EXIT key.

Please Note: if a hard drive is not connected to the USB port or timeshift is not enabled, pressing the PAUSE key, will only temporarily pause the image and there will be no recording.

Please Note : The DVR CONFIGURATION submenu lets you configure a partition for Timeshift recording on a suitable drive when it is connected to one of the USB sockets (see page 10).

YouTube Video Playback
Providing you have connected the receiver to a network which is connected to the internet you can open YouTube in the main menu and playback videos.

Subtitles and Audio Description

• Press the SUBTITLES key on the remote to switch on subtitles if they are supported for the channel you are playing.
• Similarly press the AD key to switch the audio description if it is available

Audio Track Output
Press the AUDIO key on the remote to see If a separate digital audio track is broadcast for the channel playing. You can select the track and output to a Hi-Fi amplifier via the digital audio coaxial port on the receiver.

Info Key
Press the i (INFO) key once to call up the main information bar showing current channel and now and next programme info. Press twice, to display more detailed information about the channel, satellite and transponder.

Specifications

DVBS2X: 1/23/5,2/3,3/4, 4/5, 5/6, 8/9, 9/10(QPSK)3/5 ,2/3, 3 4, 5/6, 8/9, 9/10 (8PSK)
Symbol Rate| DVB-S: 2.0 ~ 45 MS/s
Demodulation| QPSK, 8PSK, DVB-S2:1030Mb/s(QPSK),10-31Mb/s (8PSK)
Demultiplexer| Standard| ISO/IEC 13818-1
Input Max. Bit Stream Rate| 100Mbps (Serial) / 12. 5Mbps (Parallel)
Video Decoding| Standard| ISO/IEC 13818-2, MPEG-2 MP@ML, MPEG-4, AVC (MP L4.1)
Aspect Ratio| 4:3, 16:9
Video Format| PAL-B / NTSC-M / PAL-N / PAL-M
Video Resolution| 1080p, 1080i, 720p, 480p / 576p, 480i / 576i SD, compatible
Audio Decoding| Standard| ISO/IEC 13818-3
Decoding| MPEG-1 Layer | and II, MPEG-2, MPEG-4 AAC
Output Mode| LPCM, RAW
Sampling Frequency| 32, 44.1, 48KHz
Volume Level| 24 Levels
AV Output| Video de emphasis| CCIR REC.405-1, 625LINES
Video bandwidth| 5.5MHz
Video output impedance| 750
Video output level| 1.0Vp-p
Audio output| Stereo
Audio output frequency| 20Hz ~ 20KHz
Audio output impedance| Low
Audio output level| A 1.0Vrms ± 2dB into 10K.
Panel Interface|

• 1x Mini AV
• 1x HDMI
• 1x LNB In
• 1x ANT In
• 2x USB 2.0 Port
• 1x Ethernet
• 1x DC-IN
• 1x Coaxial

Power| Power input Specification| 12V/1A DC In Max. 8W

Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore some of the instructions, specifications and pictures in this documentation may differ slightly from your particular situation. All items described in this guide are for illustration purposes only and may not apply to your particular situation. No legal right or entitlements may be obtained from the description made in this manual.

Declaration of Conformity

• Hereby, Philex Electronic Ltd. declares that the radio equipment: Labgear LCOM1 Combo HD Satellite & Terrestrial Receiver for reception of satellite and terrestrial signals in domestic premises is in compliance with the Radio Equipment Directive 2014/53/EU.
• The full text of the EU declaration of conformity is available at the following internet address: www.philex.com/doc

Technical Support
If you experience problems using your combo receiver, or require further information please visit our technical support website at: www.labgear.co.uk/support

Power Supply: ErP/EuP directive No. (EU) 2019 (1782)

• Manufacturer Trademark Address: Philex Electronic Ltd. London Road, Bedford, MK42 0NX, UK. Registration No. 339123
• Model identifier LM-802B-120100L02CE, LM-802B-120100L16CE
• Input voltage 100-240 VAC
• Input AC frequency 50/60Hz
• Output voltage 12.0 V DC
• Output current 1.0 A
• Output power 12 W
• Average active efficiency (230V/50Hz) 84.96%
• Efficiency at low load (10 %) (230V/50Hz) 77.27%
• No-load power consumption (230V/50Hz) 0.09 W

The terms HDMI® and HDMI® High-Definition Multimedia interface, and the HDMI® Logo are trademarks or registered trademarks of HDMI® Licensing LLC in the UK and other countries.

• Waste electrical and electronic products should not be disposed of with household waste.
• Please recycle where facilities exist.
• Check with your Local Authority for recycling advice.

To see the full range of Satellite and TV reception and distribution accessories ideal for use with the LCOM1 visit: www.labgear.co.uk

Labgear, Philex House London Road, Bedford, MK42 0NX, United Kingdom.
EU Distributor: Philex Electronic Ireland Ltd., Robwyn House, Corrintra, Castleblayney, Co. Monaghan, A75 YX76, Ireland.
© Labgear 2022 Vb1.2

Documents / Resources

| Labgear LCOM1 Combo HD Satellite and Terrestrial Receiver [pdf] User Guide
LCOM1 Combo HD Satellite and Terrestrial Receiver, LCOM1, Combo HD Satellite and Terrestrial Receiver, Satellite and Terrestrial Receiver, Terrestrial Receiver, Receiver
---|---

References

• DishPointer - Align your satellite dish
• Labgear – Philex
• wolfbane.net
• TV & Sat. Signal Meters Archives - Labgear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>