Labgear HDM 8SP4K 8 Way 4K HDMI Splitter User Guide
- June 17, 2024
- Labgear
Table of Contents
Labgear HDM 8SP4K 8 Way 4K HDMI Splitter User Guide
HDM 8SP4K
Supports:
Full 3D
Remote control via IR back channel
Ultra HD 4K x 2K resolutions
Introduction:
Your Labgear 8 way splitter splits the signal from a single HDMI source input
to eight HDMI display outputs simultaneously.
The splitter supports full Ultra HD 4k x 2k (3840 x 2160) and dual stream 3D.
The HD input device can either be controlled at source or remotely from any of
the display locations using an IR receiver* with HDMI break in adaptor and an
IR emitter. The splitter is housed in a high quality metal housing.
Pack Contents
• 1x 8 way HDMI splitter
• 1x 5V DC power supply
• User manual
Features
• HDMI, HDCP 1.2 and DVI compliant
• Supports full 3D pass-through
• Supports 4k x 2k high resolution
• Bi-directional IR control system
• Support for CEC bypass
• External and internal EDID settings
*Please Note IR receiver, HDMI break in adaptor and IR emitter are sold separately in a kit part no. HDM IRK
Front Panel
Rear Panel
IR Connections
Operation:
1. Use a 4k compatible HDMI lead (not more than 7m long) to connect the HD
signal source (e.g. Blu-ray player, PS3, HD satellite box) to the HDMI input
socket on the splitter.
2. Use four 4k compatible HDMI leads (not more than 7m long) to connect the
four HD display devices (e.g. HD LCD, HD Plasma, HD LED) to the HDMI output
sockets on the splitter).
3. Connect the power adaptor supplied to the socket on the splitter and plug
it into a 3 pin mains socket.
4. To select one of the display’s resolutions as standard press the EDID
selection button repeatedly. Slide the EDID switch to the “OFF” position to
lock the resolution, the other seven displays will automatically show the same
resolution.
If however you want each display to show the resolution it is set to, slide
the EDID switch to the “ON” position.
Please Note: Longer HDMI input and output leads can be used for 1080p signals
– up to 20m for input and 15m for output.
IR Channel:
To control the HD source from the location of one of the displays:
1. Connect an IR emitter to the output port on the front panel of the
splitter. Place the emitter in direct line-of-sight of the IR sensor on the
devce to be controlled.
2. Connect an IR receiver to an HDMI break in adaptor plug the HDMI cable
into the adaptor and plug the adaptor into the HDMI port on the display.
3. You should now be able to operate the HD source device using its remote
control. Make sure that the remote being used is in direct line-of-sight of
the IR receiver.
*Please Note IR receiver, HDMI break in adaptor and IR emitter are sold separately in a kit part no. HDM IRK
Specifications
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT DAMAGE:
1. Do not expose this equipment to rain, moisture, dripping or splashing
liquids and make sure that no objects filled with liquids, such as vases, are
placed on or near the equipment.
2. Ensure the units are well ventilated. Do not install or place the units in
a bookcase, built-in cabinet or other confined space.
3. Do not install near heat sources such as radiators, heaters, or res.
5. Do not place sources of naked flames, such as lighted candles on the unit.
6. Clean this apparatus only with a dry cloth.
7. Unplug the power adaptor from the mains during thunder storms or when the
equipment is not in use for a long time.
8. Position the power cord and units carefully to avoid accidents or damage
to your equipment.
9. Only use the power adaptor supplied or one with the same rating.
10. Only use accessories specied by the manufacture.
11. Don not open casing there are no user serviceable parts.
Refer all servicing to qualified service personnel.
Technical Support
For further information, please contact:
Customer Careline: 08457 573 479
Local rate: UK Only
Waste electrical and electronic products must not be disposed of with
household waste. Please recycle where facilities exist.
Check with your Local Authority for recycling advice.
© Philex Electronic Ltd. 2014. v1 MK42 0NX
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>