OZITO DSR-2000 200W Detail Sander Instruction Manual

OZITO DSR-2000 200W Detail Sander

SPECIFICATIONS

• Motor: 200W
• Input: 230-240V ~50Hz
• No Load Speed: 15,000/min
• Pad Size: 140x140x80mm
• Paper Fitment: Hook & Loop
• Power Cord: 2m
• Weight: 1.5kg

WHAT’S IN THE BOX

WARRANTY

• TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.
• BEFORE RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:
• Australia 1800 069 486
• New Zealand 0508 069 486
• TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING
• TO THE WARRANTY POLICY OR PROCEDURE.
• The benefits provided under this warranty are in addition to other rights and remedies that are available to you at law.
• Our goods come with guarantees that cannot be excluded by law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
• You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
• Generally, you will be responsible for all costs associated with a claim under this warranty, however, where you have suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by contacting our customer service helpline above.

3-YEAR REPLACEMENT WARRANTY

• Your product is guaranteed for 36 months from the original date of purchase. If a product is defective it will be replaced under the terms of this warranty.
• Warranty excludes consumable parts, for example: carbon brushes, dust bags, backing pads, and sanding sheets.

WARNING

• The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other than that specified on the tool.
• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents, or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.

KNOW YOUR PRODUCT

DETAIL SANDER

1. Hook & Loop Sanding Pad
2. On/Off Switch
3. Soft Grip
4. Dust Canister Adapter
   • ACCESSORIES
5. Dust Canister
6. Sanding Paper x 20 (6x60g, 8 x 80g, 6 x 120g)

SETUP & PREPARATION

1. HOOK AND LOOP SANDING SHEET
2. • WARNING: ENSURE THE TOOL IS DISCONNECTED FROM THE POWER SUPPLY BEFORE PERFORMING ANY OF THE FOLLOWING OPERATIONS.
3. When fitting sanding paper, align the holes on the sanding sheet with the holes on the sanding pad.
4. Replace the sanding sheet when it is worn.
5. Replace the hook & loop backing pad when worn (see maintenance section).
6. DUST CANISTER
   • Install
   • Push the dust canister onto the dust extraction port.
   • Empty
   • Empty dust canister when it becomes 1/3 full for optimum dust extraction.
   • Removal
   • To remove, pull the dust canister away from the extraction port.
   • For easy emptying and cleaning of the dust canister. Remove the top of the dust canister by pulling the tabs on both sides upwards.
7. ON/OFF SWITCH
   • WARNING: THE TOOL IS RECOMMENDED FOR USE WITH A RESIDUAL CURRENT DEVICE WITH A RATED RESIDUAL CURRENT OF 30MA OR LESS.
   • Connect the tool to the main power supply.
   • To turn it on, press the ‘I’ button on the housing.
   • To turn it off, press the ‘O’ button on the housing.
   • CAUTION: GUIDE THE POWER CORD DURING SANDING TO PREVENT IT BEING CAUGHT ON THE WORKPIECE OR OTHER OBJECTS.
8. SANDING
9. • WARNING: THIS PRODUCT IS NOT RECOMMENDED FOR SANDING DRYWALL OR PLASTER DUE TO THE ULTRA-FINE SANDING PARTICLES PRODUCED. DRYWALL SANDERS IN CONJUNCTION WITH DUST EXTRACTION ARE RECOMMENDED FOR DRYWALL AND PLASTER SANDING APPLICATIONS.
10. Secure the material to be sanded.
11. Firmly grasp the sander and turn the sander on.
12. Let the motor build up to maximum speed. Gradually lower it onto the workpiece with a slight forward movement.
13. For optimum results, use either of these strokes.

MAINTENANCE

• Keep the ventilation vents of the sander clean at all times and, if possible, prevent foreign matter from entering the vents.
• After each use, blow air through the sander housing to ensure it is free from all dust particles that may build up. The build-up of dust particles may cause the sander to overheat and fail.
• If the enclosure of the sander requires cleaning, do not use solvents but a moist soft cloth only. Never let any liquid get inside the sander; never immerse any part of the ander into a liquid.

Replacing the Hook & Loop Backing Pad

After considerable use, the hook and loop backing pad surface will become worn and must be replaced when it no longer offers a firm grip. The replacement backing pad can be ordered through the Special Orders Desk at any Bunnings store.

1. To replace, remove the four Philips head screws by rotating anti-clockwise.
2. Place a new backing pad on the tool and retighten the four Philips head screws by rotating clockwise.

Note: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the tool by an unauthorized person or by the mishandling of the tool.

Supply Cord Replacement

If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent to avoid a safety hazard.

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

• Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice.
• Recycling packaging reduces the need for landfills and raw materials. The reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice.

TROUBLESHOOTING

Sparking visible through the housing air vents

• A small amount of sparking may be visible through the housing vents.
• This is normal and does not indicate a problem.

Excessive sparking visible through the housing air vents and/or the sander failing to operate

This may indicate the carbon brushes have worn out and need to be replaced. Carbon brushes should only be replaced by a qualified electrician or power tool repairer.

Sandpaper Selection

• Selecting the correct grit of sandpaper is an important step in achieving optimum results. Coarse grit will remove the most material. Finer grit will produce a smoother finish.
• The condition of the workpiece will determine the grit of the sandpaper to be used.
• The higher the grit number, the finer the grade of sandpaper.
• If the surface is rough, start with coarse grit and sand until the surface is uniform. Medium grit may then be used to remove scratches left by the coarser grit.
• A finer grit is then used to finish the surface. Always continue sanding with each grade of sandpaper until the surface is uniform.

MATERIAL/APPROPRIATE GRIT

• Note: If intermediate sanding is required, choose a grit rating between coarse and fine. The above table is intended as a guide only.
• To ensure a satisfactory result, a small, inconspicuous area should first be tested to ensure the grit of the sandpaper chosen is suitable for the desired finish.

Sanding Tips

• Never force the sander. The weight of the sander supplies adequate pressure, allowing the sandpaper to do the work. Applying additional pressure will slow the motor, rapidly wear the sandpaper, and greatly reduce the sander speed.
• This will slow the removal rate and produce an inferior-quality surface.
• CAUTION: Excessive pressure will overload the motor, causing possible damage to the sander by overheating the motor; or damage to the workpiece.
• Be sure to check your workpiece often. The sander is capable of removing material rapidly, especially with coarse paper.
• The orbital action of your sander allows you to sand with the grain, or at any angle across it for most sanding jobs. In the final stages, a better finish will be achieved by sanding with the grain.
• Do not sand on one spot for too long. The sander’s rapid action may remove too much material, creating an uneven surface.

SPARE PARTS

• Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse.
• For further information, or any parts not listed here, visit www.ozito.com.au or contact Ozito Customer Service: Australia 1800 069 486
• New Zealand 0508 069 486
• E-mail: enquiries@ozito.com.au

ELECTRICAL SAFETY

• WARNING! When using mains-powered tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury, and material damage.
• Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.
• Save these instructions and other documents supplied with this tool for future reference.
• The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate.
• Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.
• This tool is double insulated therefore no earth wire is required.
• If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer to avoid a hazard.
• Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead

• Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of damage, wear, and aging. Replace the extension lead if damaged or defective.
• When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock.

GENERAL POWER TOOL SAFETY WARNINGS

• WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.
• Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety
   • a. Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
   • b. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes.
   • c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2. Electrical safety
   • a. Power tool plugs must match the outlet. Never modify the plug in any way.
   • Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
   • b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
   • c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
   • d. Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool.
   • Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
   • e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
3. Personal safety
   • a. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
   • b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
   • c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
   • d. Remove any adjusting key or wrench before turning the power tool on.
   • A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
   • e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
   • f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
   • g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
   • h. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
4. Power tool use and care
   • a. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
   • b. Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
   • c. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
   • d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
   • e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
   • f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
   • g. Use the power tool, accessories tool bits, etc. under these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
   • h. Keep handles and grasping surfaces dry, clean, and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
   • a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

DETAIL SANDER SAFETY WARNINGS

WARNING!

• Hold the power tool with insulated gripping surfaces, because the sanding pad may contact its cord. Cutting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• Recommendation that the tool always be supplied via a residual current device with a rated residual current of 30 mA or less.
• Unplug the sander before changing accessories. Accidental start-ups may occur if the sander is plugged in while changing an accessory.
• Disposing of dust. Be extremely careful of dust disposal, materials in fine particle form may be explosive. Do not throw sanding dust on an open fire. Spontaneous combustion, may in time, result from a mixture of oil or water with dust particles.
• Always wear eye protection and a dust mask for dusty applications and when sanding overhead. Sanding particles can be absorbed by your eyes and inhaled easily and may cause health complications.
• Use special precautions when sanding chemically pressure-treated timber, paint that may be lead-based, or any other materials that may contain carcinogens.
• A suitable breathing respirator and protective clothing must be worn by all persons entering the work area. Work should be sealed by plastic sheeting and persons not protected should be kept out until the work area is thoroughly cleaned.
• Do not ‘wet sand’ with this sander. Liquids entering the motor housing are an electrical shock hazard.
• Do not use sandpaper intended for larger sanding pads. Larger sandpaper will extend beyond the sanding pad causing snagging, tearing of the paper, or kick-back.
• Extra paper extending beyond the sanding pad can also cause serious lacerations.

WARNING!

• Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contain chemicals known to cause cancer, birth defects, or other reproductive harm.

Some examples of these chemicals are:

• Lead from lead-based paints;
• Crystalline silica from bricks, cement and other masonry products, and;
• Arsenic and chromium from chemically-treated timber.
• Your risk from these exposures varies, depending on how often you do this type of work.
• To reduce your exposure to these chemicals: work in a well-ventilated area and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
• ozito.com.au

Documents / Resources

| OZITO DSR-2000 200W Detail Sander [pdf] Instruction Manual
DSR-2000 200W Detail Sander, DSR-2000, 200W Detail Sander, Detail Sander, Sander
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>