ozito BGRT-121 120W 75mm Bench Grinder And Flexible Drive Instruction Manual

ozito BGRT-121 120W 75mm Bench Grinder And Flexible Drive

SPECIFICATIONS

• Voltage: 230-240V ~ 50Hz
• Input Power: 120W
• No Load Speed: 0 – 9,900/min
• Wheel: Ø 75 x 20mm
• Wheel Bore: Ø 10mm
• Wheel Max. Speed : 40 m/s
• Weight: 2.5 kg
• ozito.com.au

WHAT’S IN THE BOX

WARRANTY

TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. BEFORE RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:

• Australia 1800 069 486
• New Zealand 0508 069 486

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY OR PROCEDURE.

The benefits provided under this warranty are in addition to other rights and remedies that are available to you at law. Our goods come with guarantees that cannot be excluded by law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Generally, you will be responsible for all costs associated with a claim under this warranty, however, where you have suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by contacting our customer service helpline above.

3-YEAR REPLACEMENT WARRANTY
Your product is guaranteed for 36 months from the original date of purchase. If a product is defective it will be replaced by the terms of this warranty. Warranty excludes consumable parts, for example: grinding & polishing wheels, carbon brushes, etc..

WARNING
The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other than that specified on the tool.
• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents, or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial, or high-frequency use.

KNOW YOUR PRODUCT

BENCH GRINDER

1. Safety Eye Shield

2. Wheel Guard Cover

3. Grinding Wheel

4. Safety Shield Bracket

5. Tool Rest Adjusting Knob

6. On/Off Switch

7. Variable Speed Dial

8. Mounting Holes

9. Safety Shield Adjusting Screw

10. Polishing Wheel

11. Tool Res
    ACCESSORIES

12. Spanner

13. Locking Pin

14. Flexible Drive

ONLINE MANUAL
Scan this QR Code with your mobile device to take you to the online manual.

SETUP & PREPARATION

ASSEMBLY
The Bench Grinder is a combination tool for the grinding and polishing of metals, plastics, and other materials.

• IMPORTANT! THE EQUIPMENT AND PACKAGING MATERIAL ARE NOT TOYS. DO NOT LET CHILDREN PLAY WITH PLASTIC BAGS, FOILS OR SMALL PARTS. THERE IS A DANGER OF SWALLOWING OR SUFFOCATING!
• IMPORTANT! BEFORE ASSEMBLING YOUR BENCH GRINDER, MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL DISCONNECTED FROM THE POWER SUPPLY TO PREVENT ACCIDENTAL STARTING.

Securing the Grinder
Before operating the Bench Grinder, it should be firmly secured to a workbench or a stable base. Insert screws through the two mounting holes at either side of the base and use a screwdriver to fix the grinder to the surface.

Fitting the Safety Shield Brackets

NOTE: All covers and safety devices must be properly fitted correctly before the equipment is switched on.

1. Safety shields must be fitted to each wheel guard cover of the Bench Grinder before operation.
2. Attach safety shields to the wheel guard cover by inserting two adjusting screws through the slots in the safety shield bracket and the corresponding holes in the safety hood.
3. Position the safety shield bracket so that the distance between the grinding wheel and the safety shield bracket is as small as possible and does not exceed 2 mm.
4. Hold the nut at the rear of the safety shield bracket in place with a spanner, while tightening the front adjusting screws with a screwdriver.

NOTE: Adjust the safety shield bracket periodically to compensate for wear on the grinding wheel.

Fitting the Safety Eye Shields

1. Position the safety eye shields between the vertical braces at the top of the safety shield brackets.
2. Insert a long screw through a washer, then through the safety shield bracket and safety eye shield (screws and washers supplied).
3. Place a washer on the end of the screw and fasten the assembly in place with a nut.
4. Hold the nut in place with a spanner, while tightening the screw with a screwdriver. Do not over tighten.

Fitting the Adjustable Tool Rest
The Bench Grinder comes with two adjustable tool rests that aid the user in holding items steady as they are being applied to the grinding wheels.

1. Align the slot in the tool rest with the hole in the bottom of the wheel guard cover.
2. Place the washers on the threaded end of the star screw.
3. Secure the adjustable tool rest to the grinder using the starscrew. Do not fully tighten until the final adjustments have been made.
4. Adjust the tool rest so that the distance between the grinding wheel and the tool rest is as small as possible and does not exceed 2 mm. Tighten the star screw.

THE FLEXIBLE SHAFT

Installing the Flexible Drive

NOTE: Fitting the accessory flexible drive shaft is optional and should only be fitted when required.
The flexible drive is designed for the grinding, deburring, polishing, engraving, cutting, milling, and cleaning of wood, metal, and plastic in model making, in workshops, and in the home. Use the tool and its accessories only for the applications described.

1. Insert the internal shaft of the flexible drive into the guide shaft on the right-hand side of the grinder.
2. Secure the fastening nut of the flexible drive to the equipment thread by hand (left-hand thread).

NOTE: Adjust the tool rest periodically to compensate for wear on the grinding wheel.

IMPORTANT! WHEN YOU WORK WITH THE FLEXIBLE DRIVE, THE SAFETY SHIELD MUST BE PLACED RIGHT UP AGAINST THE ADJUSTABLE TOOL REST TO PREVENT ACCIDENTAL TOUCHING OF THE WHEELS.

Inserting the accessories into the Flexible Drive

1. Press the supplied locking pin into the hole in the flexible drive and turn the shaft until the pin latches in place.
2. Undo the collet chuck nut with the supplied spanner.
3. Insert the required accessory into the sleeve and tighten the collet chuck nut.

IMPORTANT! ALWAYS DETACH THE FLEXIBLE DRIVE FROM THE GRINDER WHEN NOT IN USE. AN ATTACHED FLEXIBLE DRIVE MAY WHIP ABOUT UNCONTROLLABLY IF IT IS NOT BEING HELD.

OPERATION

CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, A RESIDUAL CURRENT DEVICE (RATED 30mA OR LESS) SHOULD BE USED.

On/Off Switch

1. To switch ON the equipment set the On/Off switch to the “I” position.
2. After switching ON, wait for the equipment to reach its maximum speed of rotation. Only then should you begin with the grinding.
3. Move the On/Off switch to the “O” position to switch OFF the equipment.

Variable Speed Dial
The required speed can be set with the variable speed dial.

Speed of the flexible Drive
The correct speed depends on the tool used and the type of material being processed.

• Small cutters/grinding stones: High speed (not included).
• Large cutters/grinding stones: Low speed (not included)

Using the flexible Drive

• Precision work/ engraving: hold the drive unit like a pen.
• Rough work: hold the drive unit like the handle of a hammer.

GRINDING

1. Place the workpiece onto the tool rest.

2. Slowly guide the workpiece towards the grinding wheel, ensuring that the workpiece is at the desired angle when it makes contact.
   NOTE: Exert only light pressure on the workpiece so that it can be ground at a constant speed. Instead of forcing your work, high pressure will cause the drive unit to slow down, even stopping and overloading the motor.

3. Move the workpiece from side to side to produce an optimal grinding result. This way the grinding wheel will be evenly worn. Allow the workpiece to cool down occasionally.

IMPORTANT! IF THE GRINDING WHEEL BECOMES JAMMED DURING OPERATION, REMOVE THE WORKPIECE AND WAIT UNTIL THE TOOL REACHES ITS TOP SPEED AGAIN.
IMPORTANT! FOR YOUR SAFETY, IT IS ESSENTIAL TO SECURE SMALL WORKPIECES WITH A CLAMP OR VISE.

POLISHING

1. Apply a thin coating of polishing paste (supplied) to the surface of the Polishing wheel.
2. Press the workpiece onto the wheel and move it back and forth across the surface of the wheel.
3. Always carry out polishing work in the direction of rotation of the polishing wheel.

IMPORTANT! POLISHING IN THE OPPOSITE DIRECTION TO THE DIRECTION OF ROTATION OF THE GRINDING WHEELS CAN CAUSE DAMAGE TO THE WHEEL, WHICH IN TURN CAN RESULT IN INJURIES.

MAINTENANCE

IMPORTANT! BEFORE CLEANING YOUR BENCH GRINDER OR CARRYING OUT ANY MAINTENANCE PROCEDURE, MAKE SURE THAT THE MOTOR IS OFF AND THE TOOL DISCONNECTED FROM THE POWER SUPPLY TO
PREVENT ACCIDENTAL STARTING.

Changing the Wheels

1. Remove the 3 screws that hold the side section of the safety hood and remove the wheel guard cover.

2. With a spanner, hold the wheel nut on the opposite side in position, while loosening the wheel nut of the wheel you wish to change with another spanner.
   NOTE: The grinding wheel on the left is fastened with a left-handed thread and the wheel on the right with a right-handed thread.

3. Remove the flange and replace the grinding wheel.

4. To assemble, proceed in the reverse order.

5. Manually spin the newly mounted wheel to check that it rotates freely before operation.

Carbon Brushes
Carbon brushes will wear out after many uses, causing the Bench Grinder to spark and/or stop. The brushes are a wearing component of the Bench Grinder and should be replaced before the carbon wears out completely. Take the Bench Grinder to a suitably qualified electrician or power tool repairer for replacement. Always replace both brushes at the same time.

NOTE: Ozito Industries will not be responsible for any damage or injuries caused by the repair of the Bench Grinder by an unauthorized person or by mishandling of the Bench Grinder.

Replacing the power cable
If the power cable for this equipment is damaged, it must be replaced by the manufacturer or its after-sales service or similarly trained personnel to avoid danger.

Cleaning

• Keep all safety devices, air vents, and motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
• We recommend that you clean the device immediately each time you have finished using it.
• Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device. The ingress of water into an electric tool increases the risk of an electric shock.

Storage
Store the equipment and accessories out of children’s reach in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

DESCRIPTION OF SYMBOLS

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way. Please recycle where facilities exist. Check with your local council authority for recycling advice. Recycling packaging reduces the need for landfills and raw materials. The reuse of recycled material decreases pollution in the environment. Please recycle packaging where facilities exist. Check with your local council authority for recycling advice.

SPARE PARTS

• Polishing Wheel 4412620
• Grinding Wheel 4412625
• Carbon Brush (Pair) 441256001021
• Safety Shield 441256001013
• Safety Shield Bracket 441256001011
• Adjustable Tool Rest-Left 441256001049
• Adjustable Tool Rest-Right 441256001037

Spare parts can be ordered from the Special Orders Desk at your local Bunnings Warehouse. For further information, or any parts not listed here, visit www.ozito.com.au or contact Ozito Customer Service:

• Australia 1800 069 486
• New Zealand 0508 069 486
• E-mail: enquires@ozito.com.au

ELECTRICAL SAFETY

WARNING! When using mains-powered tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury, and material damage. Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool. Save these instructions and other documents supplied with this tool for future reference. The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.

• This tool is double insulated therefore no earth wire is required. If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool.

Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the extension lead for signs of damage, wear, and aging. Replace the extension lead if damaged or defective. When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and electric shock.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

• Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting
• to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories tool bits, etc. to these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.

BENCH GRINDER SAFETY WARNINGS

This appliance is not intended for use by young or infirm persons unless supervised by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure that they do not play with the appliance.

• Always remove the plug from the main socket before making any adjustments or maintenance, including changing the wheel.
• Always wear eye protection and check that the safety window on the grinder is properly adjusted.
• Always turn the grinder off when it is not in use and never leave it unattended without first switching off and removing the power plug. Never leave the grinder until the grinding wheels have come to a complete stop.
• Do not let anyone under 18 years operate this tool.
• Rags, clothes, cords, string, and the like should never be left around the work area.
• If you are interrupted when operating the tool, complete the process and switch off before looking up.
• Periodically check that all nuts, bolts, and other fixings are properly tightened.
• Do not use a wheel that has received a blow, especially to the side of the wheel.
• Replace a cracked or suspect wheel.
• Always allow a new wheel to run for a few minutes at full speed before using it. Stand to one side at start-up.
• Check that the wheel rotates freely each time before start-up.
• Do not use the grinder unless all the guards are properly fitted and secure.
• Check that the tool rests are properly adjusted before commencing use.
• Do not overload the grinder. Allow the grinder to run at full speed, or close to full speed during use.
• If possible, always use clamps or a vice to hold your work.
• Always switch off before you put the flexible shaft down.
• Ensure that the lighting is adequate.
• Do not put pressure on the tool, such that it slows the motor down. Allow the attachments to work without pressure. You will get better results and you will be taking better care of your tool.
• Make sure that the wheel is not in contact with the work when you start the grinder.
• When using the grinder, use safety equipment including safety goggles or shields, ear protection, dust mask, and protective clothing including safety gloves.
• Keep the area free of tripping hazards.
• Only use accessory bits in good condition and that are recommended by the manufacturer.
• Do not touch the attachments after the operation. They may be very hot.
• Keep your hands well clear of the cutting and grinding devices.
• To prevent damage to the power cable, always lead it away from the rear of the machine.
• Use of materials containing asbestos is prohibited.
• The machine may exceed 85 db (A) at the workplace. The operator will require noise protection measures and ear muffs if this is the case.
• Protect the main cable from becoming damaged by oil, solvents, and sharp edges.
• Make sure that the switch is turned off when connecting the tool to the power supply.
• Check that the rotating speed shown on the wheel is equal to or higher than the rated speed of rotation for the grinder.
• Make sure that the grinding wheel is of the correct size for the grinder.
• Take precautions to ensure that flying sparks do not cause any danger, e.g. that they do not hit anyone or cause inflammable substances to ignite.
• The workpiece supports and the top adjustable safety guards must always be moved as close as possible to the grinding wheel (max. 2 mm clearance).
• Grinding wheels are not allowed to be used without the safety device. The following clearances must not be exceeded: – Workpiece support/grinding wheel: max. 2 mm – Safety guard/grinding wheel: max. 2 mm
• The guard holder, workpiece support, and transparent guard must be fitted before the double grinder is used.
• Before starting work, firmly screw the grinder to the workbench, etc. using the mounting holes in the base plate.
• Adjust the spark deflector periodically to compensate for the wear of the wheel. Distance between the spark deflector and the wheel should in no case exceed 2mm.
• The grinding wheel must be replaced at the latest when the spark deflector and the workpiece support can no longer be set a maximum distance of 2mm from the grinding wheel.

Keep this safety information in a safe place. If in doubt, do not plug in the tool. Using a power source with a voltage less than the nameplate rating is harmful to the motor. The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. To use this tool properly, you must observe the safety regulations, the assembly instructions and the operating instructions to be found in this manual. All persons who use and service the machine have to be acquainted with this manual and must be informed about its potential hazards. The manufacturer shall not be liable for any changes made to the tool nor for any damage resulting from such changes. Even when the tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the tool’s construction and design:

• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective ear defenders are not worn Wear goggles, Wear ear protection, Wear a breathing mask

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>