eureka 6992 Home Cleaning System Vacuum Cleaner User Guide
- June 17, 2024
- Eureka
Table of Contents
eureka 6992 Home Cleaning System Vacuum Cleaner
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
- To reduce the risk of fire, electric shock, or injury:
- Do not use it outdoors or on wet surfaces.
- Do not leave the vacuum cleaner when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing.
- Do not allow it to be used as a toy. Close attention is necessary when used by or near children.
- Use only as described in this manual. Use only the manufacturer’s recommended attachments.
- Do not use a damaged cord or plug. If the vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center before using.
- Do not pull or carry by cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do not run the vacuum cleaner over the cord. Keep the cord away from heated surfaces.
- Hold the plug when rewinding onto the cord reel. Do not allow the plug to whip when rewinding.
- Do not use extension cords or outlets with inadequate current carrying capacity.
- Turn off all controls before unplugging.
- Always turn off this appliance before connecting or disconnecting either the hose or motorized nozzle.
- Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
- The hose contains electrical wires. Do not use if damaged, cut, or punctured. Avoid picking up sharp objects.
- Do not handle the plug or vacuum cleaner with wet hands.
- Do not put any objects into openings. Do not use any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
- This vacuum cleaner creates suction and may contain a revolving brush roll. Keep hair, loose clothing, fingers, and all parts of the body away from openings and moving parts.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Do not use without a dust bag in place.
- Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt.
- Use extra care when cleaning on stairs.
- Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
- Store your cleaner in a cool, dry area.
- Keep your work area well-lighted.
- Unplug electrical appliances before vacuuming them.
- To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other).
- The plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
- If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
GENERAL INFORMATION
- The bag may have come dislodged in shipping.
- Check the bag to ensure proper seating before attempting to use the cleaner.
- Do not operate the cleaner without a dust bag or the filters.
- Damage may result in the motor (see Dust Bag and Filter).
- The cleaner is designed to pick up dirt and dust particles.
- Avoid picking up hard or sharp objects with the cleaner to avoid bag breakage, hose clogging, or possible motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. If additional service is required, telephone toll free:
- USA: 1-800-282-2886
- Mexico: 5670-6169
- Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 N. Main Street, Bloomington, Illinois 61701, USA. The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited Warranty for complete service information. DO NOT OIL the motors (in the canister and the motorized nozzle) or the brush roll at any time. The bearings are permanently lubricated and sealed.
Rating Plate
- The model, type, and serial numbers are indicated on the rating plate located on the underneath side of the cleaner.
- For prompt and complete service information, always refer to these numbers when inquiring about service.
- Model No. & Type__
- Serial No._____
Thermal Cut Off
- This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating.
- If the cleaner suddenly shuts off, push the switch pedal once and unplug the cleaner.
- Check the cleaner for a possible source of overheating such as a blocked hose or clogged filter.
- If these conditions are found, fix them and wait at least 30 minutes before attempting to use the cleaner.
- After the 30 minutes, plug the cleaner back in and turn on the switch.
- If the cleaner still does not run, call an Eureka Service Station.
ASSEMBLY ITEMS
NOTE: Unpack and identify all parts. Fully assemble before using.
- On/Off Canister Switch
- Power Cord
- Cordaway Cord Reel Button
- Suction Control Regulator – 6996 Only
- HEPA Filter Full Indicator – 6996 Only
- Cover Release for Dust Compartment
- Hose Connection
- Power Outlet
- Dust Bag Full Indicator
- Carrying Handle
- Temporary parking position for floor nozzle and wands when in use.
- Storage slot for floor nozzle and wands, or tool caddy.
- Tool Caddy
- a) Dusting Brush
- b) Crevice Tool
- c) Upholstery Nozzle
- The hose has Power-Touch Handle with a nozzle on/off control. See instructions on pages 6 and 7.
- Button-Lock Extension Wand with plug retainer
- Button-Lock Extension Wand with cord retainer
- Motorized Nozzle
- Quick Release™ Wand System
- Floor Brush
- NOTE: Be careful when cleaning steps, etc.
How to Assemble and Use
POWER-TOUCH® Handle
- Remote ON/OFF Selector for bare floor or carpet
- Carpet – Turn on the motorized nozzle.
- Bare Floor – Turn off the motorized nozzle.
- Vacuum Control
- Cleaning suction is reduced by pushing the lever to a LOW position.
- Place the lever at a HIGH position to increase suction for carpet cleaning.
- Snap interlocking wands together.
- Push assembled wands into the quick-release socket attached to the power nozzle.
- Push the motorized nozzle plug into the retainer located at the top of the upper wand; secure the cord in the slot (Detail A).
- Place the Power-Touch hose handle into wands until the plug connects and the button locks.
- Continue on the next page to complete assembly.
- If you purchased the Dirt Sensor model, your lower wand will look like this.
- Dirt Sensor (Model 6996 only)
- NOTE: The dirt sensor works most effectively when the suction control regulator on the canister and the vacuum control on the handle are both on HIGH.
- Insert hose coupling into the front of the canister.
- Pull the cord out until fully extended, and push plug into an outlet. To rewind, step on the Cordaway cord reel button, hold and guide plug while it rewinds.
- Step on the motorized nozzle to release the handle; pull back to a comfortable work position.
- Push the On/Off canister switch. (A thermostat automatically shuts off the motor if it overheats, see Thermal Cut Off.)
- Bare floor or carpet cleaning selection on remote control, only.
- Red light indicates dirt, dust, etc. is still being removed from the area being cleaned. The green light indicates the area is clean and to move on to the next area.
- NOTE: The dirt sensor works most effectively when the suction control regulator on the canister and the vacuum control on the handle are both on HIGH.
- HINT: New carpeting has loose carpet fibers which will activate the red light sensor beam.
HOW TO MAINTAIN
- The paper bag and filter play a very important role in the efficiency of the vacuum cleaner.
- The purpose of the paper bag is to trap dirt and at the same time, the paper must be porous enough to allow air to pass through.
- If the paper bag or filter becomes clogged, no air can pass through the cleaner and no cleaning takes place regardless of how powerful the unit.
- To keep the cleaner operating at maximum efficiency, change the dust bag frequently and clean the filter as necessary.
- Some fine particles can restrict airflow very quickly and will decrease performance even before the bag appears to be full.
- When vacuuming carpet fresheners or cleaners, plaster dust, or similar fine substances, clean the bag and filter more often.
- NOTE: Turn off the power switch and disconnect the electrical plug from the wall socket before changing the dust bag. Never use the cleaner without a dust bag or filters.
HOW TO CHANGE DISPOSABLE DUST BAG
- Use GENUINE EUREKA replacement bag, 61230.
- NOTE: The lid will not latch if the dust bag is not installed.
HOW TO CHANGE MOTOR FILTER
Use GENUINE EUREKA replacement motor filter, 61263. The motor filter can be cleaned. Run under water and allow to thoroughly air dry. NOTE: Lid will not latch if dust bag is not installed.
HOW TO CHANGE HEPA FILTER AND FINAL FILTER
- Use GENUINE EUREKA HEPA filter, 60286A.
- We recommend the HEPA filter be changed every 6 months or as needed.
- Use GENUINE EUREKA Final filter, 61262.
- The final filter can be cleaned. Run under water and allow to thoroughly air dry.
How To Change or Clean Washable HEPA Filter and Final Filter (Model 6996 only)
- Use GENUINE EUREKA washable HEPA filter, 61053.
- To clean the filter rinse the dirty side of the filter under warm, low-pressure water being careful not to get the clean side wet (this increases drying time).
- Do not put the damp filter back in a vacuum cleaner. Allow to thoroughly air dry.
- Use GENUINE EUREKA Final filter, 61262. The final filter can be cleaned. Run under water and allow to thoroughly air dry.
How to Replace Worn Belt or Light Bulb
NOTE: Disconnect the power cord and wands from the electrical hose before replacing the belt or bulb. Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt.
- Remove two screws from the bottom side. To turn over, grasp the hood near the handle socket and lift forward.
- Replace the headlight bulb (on some models), if necessary.
- Support the socket with one hand and push the light bulb into the socket; turn to release.
- Place the new light bulb into the socket; turn to secure. Push the light bulb and socket back so the bulb will not touch the lens cover. Use GENUINE EUREKAreplacement bulb, 59224.
- Continue to step 2 to change the belt. Skip to steps 7 and 8 to replace the hood on the motorized nozzle.
- Remove two screws located in front of the light bulb and lift to remove the brush roll cover.
- Lift out the brush roll; replace the new belt around the brush roll shaft.
- Return the brush roll to the base.
- Rotate the belt onto the motor pulley.
- Replace the brush roll cover.
- Tilt cover over the ridge and push down.
- Secure with screws on the underside (refer to 1).
Use GENUINE EUREKA replacement belt, 52201C.
LIMITED WARRANTY
THE EUREKA LIMITED WARRANTY
- Exclusive 5-Year Motor Coverage
- This product’s motor is warranted to be free from all defects in material and workmanship in normal household use for five years.
- The warranty is granted only to the original purchaser and members of his or her immediate household. The warranty is subject to the following provisions.
- Additional Warranty Coverage
- Your Eureka cleaner is warranted to be free from all defects in material and workmanship in normal household use for one year.
- The warranty is granted only to the original purchaser and members of his or her immediate household. The warranty is subject to the following provisions.
- What This Warranty Does Not Cover
- Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, and brush roll bristles
- Damages or malfunctions caused by negligence, abuse, or use not by the Owner’s Guide.
- Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts.
- What The Eureka Company Will Do
- The Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this warranty. As a matter of warranty policy, the Eureka Company will not refund the consumer’s purchase price.
- Warranty Registration
- Please fill out and return the warranty registration card accompanying your cleaner.
- Obtaining Warranty Service
- To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station.
- You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners–Service and Repair.” Be certain that the Warranty Station is “Eureka Authorized.” For the location of the nearest Eureka Authorized Warranty Station or service information, telephone toll-free:
- USA: 1-800-282-2886
- Mexico: 5670-6169
- Canada: 1-800-282-2886
- If you prefer, you can write to The Eureka Company, Service Division, 807 N. Main Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7.
- If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping charges to the Eureka Authorized Warranty Station.
- Return shipping charges will be paid by the Warranty Station. When returning parts for repair, please include the model, type, and serial number from the data plate on the cleaner.
- Further Limitations and Exclusions
- Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of Merchantability or any warranty for Fitness For A Particular
- The purpose is limited to the duration of this warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
- Your relief for the breach of this warranty is limited to the relief expressly provided above.
- In no event shall Eureka be liable for any consequential or incidental damages you may incur in connection with your purchase or use of the cleaner.
- Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
- This warranty gives you specific legal rights. You may also have other rights which vary by state.
GENUINE
EUREKA PRODUCT
Questions & Answers about Genuine Eureka Products
- Q: Why should I use only Genuine Eureka paper bags, belts, and parts in my Eureka vacuum cleaner?
- A: Using Genuine Eureka Products, which are made to our exacting specifications and engineered with an emphasis on quality, performance, and customer satisfaction, ensures the long life and cleaning efficiency of your vacuum cleaner. Overall, this saves you money and helps to keep your home clean.
- Q: How can I be sure I am using only genuine Eureka products in my vacuum cleaner?
- A: Typically, packaged products and paper bags can be identified by a “Genuine Eureka Product” symbol (see illustration above). For further identification assistance, you may call our toll-free number, 1-800-282-2886, for the location of a nearby Eureka Authorized Warranty Station.
- Q: Are there any differences between “made to fit” or “imitation” and Genuine Eureka paper bags, belts, and parts?
- A: Yes, there are some very important differences in materials, quality, and reliability. Many customers have mistakenly purchased “imitation” paper bags and parts while thinking they purchased genuine. Unfortunately, many of these customers discovered the differences after they experienced related difficulties.
For Genuine Eureka Value, Accept No Imitations!
- THE EUREKA COMPANY Bloomington, Illinois 61701
The Eureka Company
- P.O. Box 2799
- Bloomington, IL 61702-2799
IMPORTANT: Be sure to include your model, type, and serial numbers. These numbers may be found on the rating plate.
- Model Number:
- Type:
- Serial Number:
To Order
- By Phone 1-800-438-7352*
- HOURS: Call between 8 a.m. and 4:45 p.m., central standard time Monday through Friday.
- By FAX 1-309- 823-5789
- To Answer Problems or Questions for the U.S.A. and Canada call: 1-800- 282-2886* 7 a.m. to 8 p.m. central standard time Monday through Saturday.
- En Mexico llame al 5670-6169 By Mail: Simply fill out this Order Form. Please be sure to include day and evening phone numbers.
- www.eureka.com.
- 70988A
- © 2002 White Consolidated Ltd. Printed in U. S.A.
- Part No. 70897A (5/02)
- www.eureka.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>