YUANMAN Tuya WiFi Access Switch User Guide
- June 4, 2024
- YUANMAN
Table of Contents
**YUANMAN**
User manual
Product Description
Product technical parameters
Receiver specifications:
- Wifi: IEEE802.11 b/g/n2.4GHz
- Working voltage: AC100 240V 50/60Hz
- Frequency: 433.92MHz
- Maximum current: 16A
- Size： 4948 23mm
Self-powered remote control switch specifications:
- Working voltage: no need for battery
- Working frequency: 433MHZ
- Standby power consumption: OuA
- Transmitting power < 10mW
- Working mode: wireless remote control
- Working temperature: -10°C ~+70°C
- Size: 868616.5(mm)
- Transmission distance:
100M (outdoor), 30M (indoor)
The transmission distance is affected by the wall barrier and may be different from the actual measured value.
Checklist before using the device
-
Your smartphone or tablet has connected to a
-
4G WiFi with the internet.
-
You have the correct WiFi password. Your smartphone or tablet must have access to
APP Store, Google Play. -
Make sure that your router is MAC-open.
User Guide
① Start with the “Smart Life”‘or TuyaSmart “APP.
I P Smart Life II P TuyaSmart I
•« CM ■ CttltCK
AppStore ］ 尸 Google Play
® Register a” Smart Life” or “TuyaSmart” account.
(D If you have Smart Life” or “TuyaSmart” account, just log in.
https://smartapp.tuya.com/tuyasmart
Product installation
Self-powered remote control switch: It can be placed or moved at will, or it can be fixed to your favorite position. Use double-sided stickers on one side to stick to the bottom of the switch, and the other side to stick it where you like.
WiFi+ R F433 MHZR receiver Installation method: it can be fixed with double-
sided stickers (note: it cannot be installed in a metal box, cannot be close
to or dose to the ground or a large metal, otherwise it may cause the normal
reception of wireless signals.)
Please wire this device according to the marking on the cover.
ON/OFF operating principle：
The connected appliances work/stop through live wire power on/off. The device
must be powered by and
Itcanbeplacedormovedatwill, or can Warning: S1 and S2 can only be connected to the two ends of the wall switch, and cannot be connected to strong power such as a zero-fire line. Wiring part: as shown in the figure, please turn off the power before wiring. Non-professionals do not live to wire.
(The wiring for 1 way control}
i The wiring for 2 way 8ntrol i
Product installation
- Turn on the power after the wiring Is complete, the device is on by default. Quickly press the receiver button three times in a row and wait for 5 seconds until the red LED flashes rapidly and then enters the distribution mode.
- Go to the application and click the + in the upper right corner of the page to enter the network connection page.
- Make sure to click on the device’s Indicator light to blink rapidly, twice per second, and continue to the next step.
- Enter your WIFI username and password.
- Change the name of your device or use the default name.
- When the WlFILED red Indicator Is lit, the device Is online.
Learning settings
The packaged product has been paired at the factory, SO this operation is not
required. If you need to add or replace the remote control switch, refer to
the following steps.
Pairing method
Long press the receiver button for 5 seconds, the blue LED lights up, enter
pairing mode, press the remote control switch, and the receiver blue light
flashes then the pairing is successful.
Clear function
Long press the receiver button for 10 seconds, the blue LED indicator flashes
quickly three times, then the code is cleared successfully.
Cautions
- The load power cannot be greater than the rated power of the product.
- When using wireless electronic products, pay attention to avoiding metal masks, large electronic devices, electromagnetic fields, and other strong sources of interference to avoid short distances between the remote control and the receiver or failure to work properly.
- Do not use this electronic product abnormally. Abnormal use will reduce the performance and life of the product. In severe cases, it will damage the product and bring hidden dangers to your safety.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>