Philips Norelco ‎BT9810 Series 9000 Hair Trimmer INSTRUCTIONS Manual

June 17, 2024
Philips Norelco

Philips Norelco ‎BT9810 Series 9000 Hair Trimmer

IMPORTANT SAFETY INSTRUCTIONS

When using an electric product, basic precautions should always be followed, including the following:
Read all instructions before using this product.

DANGER

  • To reduce the risk of electric shock:
  • Do not reach for a corded product that has fallen into the water. Unplug immediately from the power outlet.
  • Use product only in dry condition. Do not use it while bathing or in a shower.
  • Do not place or store the product where it can fall or be pulled into a tub or sink. Do not place or drop the product into water or other liquid.
  • Except when charging, always unplug this product from the power outlet immediately after use.
  • Detach the hand-held part from the supply cord before cleaning it in water.

WARNING

  • To reduce the risk of burns, fire, electric shock, or injury to persons:
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the  appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
  • Use this product only for its intended household use as described in this manual. Do not use attachments not recommended by Philips North America LLC.
  • Never operate this product if it has a damaged power cord, if it is not working properly, after it has been dropped or damaged, or after the product or power cord has been dropped into water. For assistance call 1-800-243-3050.
  • Keep the power cord away from heated surfaces.
  • Never drop or insert any object into any opening.
  • Do not use the power cord in or near a power outlet that contains an electric air freshener to prevent damage to the power cord.
  • Do not use products outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
  • Always check cutters, cutting unit, and guards before using the product. Do not use the product if cutters, cutting unit or guards are damaged, as injury may occur.
  • Always attach the power cord to the product first, then to power outlet. To disconnect, set all controls to ‘off’ position. Then remove the power cord from power outlet.
  • Plug the power cord directly into power outlet. Do not use an extension cord.
  • Unplug power cord before plugging in or unplugging the product.
  • Only use the power cord and other accessories supplied with the product.
  • Do not attempt to open the product to remove or replace the built-in rechargeable battery.
  • The batteries used in this product may present a fire or chemical burn hazard if mistreated. Do not disassemble, heat above 100 °C (212 °F) or incinerate.

IMPORTANT : The power plug contains a transformer. Do not cut off the power plug to replace it with another plug as this will cause a hazardous condition.

Battery safety instructions

  1. Only use this product for its intended purpose and follow the general and battery safety instructions as described in this user manual. Any misuse can cause electric shock, burns, fire and other hazards or injuries.
  2. To charge the battery, only use the detachable supply unit (HQ8505) provided with the product. Do not use an extension cord.
  3. Charge, use and store the product at a temperature between 40 °F / 4.5 °C and 95 °F / 35 °C.
  4. Always unplug the product when it is fully charged.
  5. Do not burn products and their batteries and do not expose them to direct sunlight or to high temperatures (e.g. in hot cars or near hot stoves). Batteries may explode if overheated.
  6. If the product becomes abnormally hot, gives off an abnormal smell, changes color or if charging takes much longer than usual, stop using and charging the product and contact your local Philips dealer.
  7. Do not place products and their batteries in microwave ovens or on induction cookers.
  8. This product contains a non-replaceable rechargeable battery. Do not open the product to replace the rechargeable battery.
  9. When you handle batteries, make sure that your hands, the product, and the batteries are dry.
  10. To prevent batteries from heating up or releasing toxic or hazardous substances, do not modify, pierce or damage products and batteries and do not disassemble, short-circuit, overcharge or reverse charge batteries.
  11. To avoid accidental short-circuiting of batteries after removal, do not let battery terminals come into contact with metal objects (e.g. coins, hairpins, rings). Do not wrap batteries in aluminum foil. Tape battery terminals or put batteries in a plastic bag before you discard them.
  12. If batteries are damaged or leaking, avoid contact with the skin or eyes. If this occurs, immediately rinse well with water and seek medical care.
    SAVE THESE INSTRUCTIONS

Introduction
Congratulations on your purchase and Welcome to Philips Norelco!
To fully benefit from the support that
Philips Norelco offers, register your product at www.norelco.com/register.

General description (Fig. 1)

  1. Beard guard (5.4-10 mm/7/32-25/64 in)
  2. Cutting unit
  3. Zoom wheel
  4. On/off button
  5. Battery charge indicator
  6. Socket for small plug
  7. Bottle of oil
  8. leaning brush
  9. ower plug
  10. Small plug
  11. Pouch

Charging

Battery status indicator

  1. When the battery is almost empty, the battery charge indicator starts flashing orange.

  2. When the product is charging, the bottom light of the battery charge indicator starts flashing white, then the next one, and so on.

  3. When the product is fully charged, all lights of the battery charge indicator light up white.

  4. The remaining battery charge is indicated by the lights of the battery charge indicator that lights up continuously.
    Note : After approx. 30 minutes, the lights of the battery charge indicator go out automatically.
    Charge the product fully before you use it for the first time and after a long period of non-use.

  5. Charging or using the product at temperatures below 40 °F (4.5 °C) or higher than 95 °F (35 °C) adversely affects the lifespan of the battery.

  6. If the product is subjected to a major change in temperature, pressure or humidity, let the product acclimatize for 30 minutes before using.

5-minute charge: During charging, all three lights of the battery charge indicator light up. After approx. 5 minutes of charging, the product contains enough energy for 5 minutes of use.

  1. Make sure the product is turned off.
  2. Insert the small plug into the product and put the power plug in any 120V AC outlet (Fig. 2).
  3. After charging, remove the power plug from the power outlet and pull the small plug out of the product.
    It takes approximately 1 hour to fully charge the product. When it is fully charged, the product has a cordless operating time of up to 120 minutes.
    Note : An adapter plug may be necessary for cord usage in some foreign countries. Use an attachment plug adapter of the proper configuration for the power outlet.

Using the product

Use the product only in dry conditions. Do not use it while bathing or in a shower. This symbol (Fig. 3) indicates that the product can be rinsed under running tap water.Always check the product and all accessories before using. Do not use the product or any accessory if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type.

Trimming without guard
If you trim without the guard, your hair is cut close to the skin.
You can turn the zoom wheel to choose from length settings ranging from 0.4 mm (1/64 in) to 5 mm (7/32 in.).

  1. Make sure the product is turned off.

  2. Pull the guard off the product.

  3. Turn the zoom wheel to select the desired length setting.

  4. Turn on the product.

  5. Make well-controlled movements. Touch the hair lightly with the trimmer.
    For a comfortable trim close to your skin, place the flat side of the trimming head against your skin and make strokes in the desired direction (Fig. 4).

  6. Turn off and clean the product after each use (see ‘Cleaning’).

Edging without guard
You can also use the trimming head without the guard to:

  • Define the hairline
  • Trim the nape of the neck
  • Remove single unwanted hairs

Note: The metal part of the cutting edge does not bend and therefore ensures an even cut.

  1. Make sure the product is turned off.
  2. Pull the guard off the product.
  3. Turn on the product.
  4. Make well-controlled movements. Touch the hair lightly with the trimmer.
    • For contouring, hold the trimming head perpendicular to the skin and move the trimming head upwards or downwards with gentle pressure (Fig. 5).
  5. Turn off and clean the product after each use (see ‘Cleaning’).

Trimming with guard

Note : When you trim for the first time, start at a length setting that is longer than what you are used to, to familiarize yourself with the product.
Use the beard guard to trim your beard, stubble, and mustache in your preferred style.
Turn the zoom wheel to choose from length settings ranging from 5.4 mm (7/32 in.) to 10 mm (25/64 in.) (Fig. 7). The length settings are mentioned above the zoom wheel.

  1. Make sure the product is turned off.
  2. To attach the guard, slide the front part of the guard onto the teeth of the cutting unit. Then push down the center of the guard with your fingers or the palm of your hand (‘click’) (Fig. 6).
  3. Turn the zoom wheel to select the desired length setting.
  4. Turn on the product.
  5. To trim most effectively, move the product against the hair growth direction. Make sure that the surface of the guard always stays in contact with the skin (Fig. 8). Since all hairs do not grow in the same direction, you may want to try different trimming directions (i.e. upwards,  downwards, or across). Practice is best for optimum results.
  6. Regularly remove cut hair from the guard. If a lot of hair has accumulated in the guard, remove it from the product and blow and/or shake out the hair. The selected hair length setting does not change when the guard is removed.
  7. Turn off and clean the product after each use (see ‘Cleaning’).
    • Use this product for its intended household use as described in this manual.
    • For hygienic reasons, the product should only be used by one person.
      Note : This appliance can be used without a cord or when it is connected to the wall socket.

Cleaning

Never use scouring pads, abrasive cleaning agents, or aggressive liquids such as petrol or acetone to clean the appliance.
Clean the product after each use (see ‘Cleaning’).

  1. Turn off the product and disconnect it from the power outlet.
  2. Wipe the housing of the product with a dry cloth.
  3. Clean the trimming head under the tap (Fig. 9).
  4. Pull the back part of the guard off the product and then slide it off the cutting unit (Fig. 10).
  5. Clean the guard with the cleaning brush (Fig. 11) and/or rinse it under the tap (Fig. 12).
  6. Clean the cutting unit with the cleaning brush and/or rinse it under the tap (Fig. 14).
  7. Carefully shake off excess water and let all parts air dry completely.
    Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth.

Every 3 months: cleaning trimming head connector

  1. Turn off the product and disconnect it from the power outlet.
  2. Pull the cutting unit off the product (Fig. 13).
  3. Clean the inside of the trimming head with the cleaning brush (Fig. 15).
  4. Clean the trimming head connector with the cleaning brush (Fig. 16).
  5. Press the trimming head back on the product. Make sure the projection on the back of the trimming head fits exactly onto the notch in the hair chamber (Fig. 17).

Lubricating the trimmer teeth with oil

  • When the oil indicator light lights up (Fig.18) lubricate the trimmer teeth with a drop of oil (Fig. 19).
    Tip: For optimal performance, lubricate the trimmer teeth with a drop of the oil supplied twice per week.
    This product has no other user-serviceable parts. For assistance call 1-800-243-3050.

Travel lock
When you are going to travel, you can lock the trimmer to prevent it from accidentally turning on.

Activating the travel lock
Press the on/off button for 3 seconds to use the travel lock mode (Fig. 20).

  • When the travel lock is activated, the travel lock symbol flashes (Fig. 21).
  • If you try to turn on the product while the travel lock is active, the travel lock symbol flashes.

Deactivating the travel lock
Press the on/off button for 3 seconds (Fig. 20).

  • While you deactivate the travel lock, the travel lock symbol lights up briefly. The product turns on and is now ready for use again.
    Note : You can also deactivate the travel lock by connecting the product to the power outlet.

Storage

  • Be sure the product is switched off. Remove the power cord from the power outlet and the product before storing it in a safe, dry location where it will not be crushed, banged, or subject to damage.
  • Do not wrap cord around the product when storing.
  • Store the product in the pouch supplied. Make sure the product is dry before you store it in the pouch.
  • Do not place or store the product where it can fall or be pulled into a tub or sink, water or other liquid while plugged in.

Assistance

For assistance, visit our website: www.philips.com/support or call toll-free 1-800-243-3050.
Online information is available 24 hours a day, 7 days a week.

Disposal

  • This product contains a rechargeable lithium-ion battery which must be disposed of properly (Fig. 22). Contact your local town or city officials for battery disposal information. You can also call 1-800-822-8837 or visit: www.call2recycle.org for battery dropoff locations.
  • Your product is designed and manufactured with high-quality materials and components, which can be recycled and reused. For recycling information, please contact your local waste management facilities or visit: www.recycle.philips.com

Full Five-Year Warranty

Philips North America LLC warrants this new product (except blade and guards) against defects in materials or workmanship for five years from the date of purchase, and agrees to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable care, the affixing of any attachment not provided with the product or loss of parts or subjecting the product to any but the specified voltage or batteries.
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
To obtain warranty service, simply go to www.philips.com/support for assistance. It is suggested that for your protection you return shipments of product by insured mail, insurance prepaid. Damage occurring during shipment is not covered by this warranty.
NOTE: No other warranty, written or oral, is authorized by Philips North America LLC.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion and limitations may not apply to you.
Read the enclosed instructions carefully.

45-DAY MONEY-BACK GUARANTEE
If you are not fully satisfied with your product send the product back and we’ll refund you the full purchase price. The product must be shipped prepaid by insured mail, insurance prepaid, have the Original sales receipt, indicating purchase price and date of purchase, and the money-back guarantee return authorization form is enclosed.
We cannot be responsible for lost mail.
The product must be postmarked no later than 45 days after the date of purchase. Philips reserves the right to verify the purchase price of the product and limit refunds not to exceed the suggested retail price.
To obtain the money-back guarantee service, please go to www.PhilipsMoneyBack.com and follow the simple 3-step process. Delivery of refund check will occur 6–8 weeks after receipt of the returned product.

FAQs

What is the Philips Norelco ‎BT9810 Series 9000 Hair Trimmer?

The Philips Norelco ‎BT9810 Series 9000 Hair Trimmer is a grooming tool designed for cutting and styling hair, including beard and facial hair.

Are the blades of the Philips Norelco ‎BT9810 trimmer sharp and durable?

Yes, the trimmer is equipped with self-sharpening stainless steel blades that are designed for long-lasting performance.

Does the trimmer include different trimming length options?

Yes, the Philips Norelco ‎BT9810 Hair Trimmer features a precision dial that allows for customizable trimming lengths, offering a wide range of options to achieve your desired style.

What is the runtime of the Philips Norelco ‎BT9810 on a full charge?

On a full charge, the Philips Norelco ‎BT9810 can provide up to 120 minutes of runtime, depending on usage.

How long does it take to fully charge the Philips Norelco ‎BT9810 trimmer?

It typically takes about 1 hour to fully charge the Philips Norelco ‎BT9810 Hair Trimmer.

What are the key features of the Philips Norelco ‎BT9810 Hair Trimmer?

The key features of the Philips Norelco ‎BT9810 include a precision dial for adjustable trimming lengths, self-sharpening stainless steel blades, and various attachments for precise grooming.

Is the Philips Norelco ‎BT9810 Series 9000 Hair Trimmer suitable for all hair types and styles?

Yes, the Philips Norelco ‎BT9810 is designed to work well with various hair types and styles, and its adjustable trimming lengths cater to a wide range of grooming preferences.

Can I use this trimmer while it's charging?

Some cordless trimmers, including the Philips Norelco ‎BT9810, offer the option of using them while charging. Refer to the product manual for specific instructions.

Is this trimmer easy to clean?

Yes, the Philips Norelco ‎BT9810 Hair Trimmer is designed for easy cleaning. You can rinse the detachable parts under running water for maintenance.

Can the Philips Norelco ‎BT9810 trimmer be used for body grooming as well?

Yes, in addition to facial hair, the Philips Norelco ‎BT9810 can be used for body grooming and trimming other areas of the body.

Is this trimmer suitable for both wet and dry use?

The Philips Norelco ‎BT9810 Hair Trimmer is designed for both wet and dry use, making it suitable for use in the shower or with shaving gels.

Video-Philips Norelco ‎BT9810 Series 9000 Hair Trimmer

Download This Manual PDF:Philips Norelco ‎BT9810 Series 9000 Hair Trimmer INSTRUCTIONS Manual

Philips Norelco ‎BT9810 Series 9000 Hair Trimmer INSTRUCTIONS Manual-Device. report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals