FATSPAS Luxury Shower System Installation Guide

Luxury Shower System

Installation Manual

Brand Introduction

Out factory thanks to its quality heritage, have been on a mission to bring you the very best experience of enjoy bath life for both your body and mind.
Throughout the day and night, we like to get under the skin of the city we live in.
Whether you’re enjoying a relaxing hot bath, refreshing yourself to a cutting- edge Out factory new opportunity or preparing for an upcoming festival.our aim is always to deliver an engaging, comfortable and stylish bath life
We are always thinking:
“What Can We Do For Our Customers?”
High Quality, Durable, Energy Saving, Luxury, Affordable

Aesthetically pleasing design, high production values and total temper control solution combine to create an extensive line of bathroom faucets. We are proud to add a refined sense of luxury and uniqueness to the most sophisticated baths.Hope you enjoy bath life as much as Out factory enjoy creating it.

Before Installation

Thank you for choosing our Rain Shower System. Hope that you’ll enjoy a comfort­ able smooth bathing experience with this product. Before installation, please read this installation manual carefully and keep it properly in case you need it. This manual is about the installation and use of this Rain Shower System.

Technique Requirement

1. Proper Water pressure should between 0.1 Mpa-1.0Mpa, If water supply pressure exceeds 1.0 Mpa, a pressure reducing value must be fitted.

2. Clean the impurity and sludge in the hose before assembling to avoid leaking and blockage.

3. This shower system needs to be installed inside the wall. Please read this manual carefully to confirm the dimensions of products and keep the proper position on the wall.

4. The intake/outlet pipes need to be wrapped with Teflon tape. Use a Teflon tape to wrap a few turns in the clockwise direction on the thread of the pipes.
   (This is very important. The direction of the Teflon tape must be tangled clockwise. If not, it will leak.)

5. Turn off the water supply before installation

Shower Sets Family Portrait

Tools you need to prepare

Product Dimensions

Notice:
The edge of the embedded box should be as flush as possible with the tile surface as shown in the figure, or slightly protrude from the tile surface by 0.8in

Installation Of Rain Shower System

Install The Shower Mixer Valve Control

• Make sure the Shower Mixer Valve is connected to the correct Hot/Cold Water side

Installation Steps

Step 1:
The intake/outlet pipes need to be wrapped with Teflon tape. Use a Teflon tape to wrap a few turns n the clockwise direction on the thread of the pipes.
Step 2:
Connect the water pipe with the embedded box

Step 3:
Confirm the location of the embedded box and the pipes. Then mark them.
Step 4:
After confirm the ocation, dig out the routes of the pipes. And remove the embedded box and drill the hole Then use the electric drill to drill white screws into the wall

Step 5:
Fix the embedded box on the wall with four screws
Step 6:
Remove the embedded box cover from the valve control, then with the handle help, each inlet and outlet pipe shall be pressure tested to ensure no leakage.

Step 7:
The embedded box cover can protect the box from dust. Cover the embedded box and wait for the wall to be tiled.
Step 8:
After the wall s tiled, remove the cover of the embedded box.

Install the panel

Step1: Cover the panel, the panel should be as close as possible to the embedded box and the switch should be at east 1 mm away from the panel to prevent scratching the panel
Step2: Fix the Rain Mixer Valve Control with a hexagonal screw and a small cover.
Step3: Fix the Single Level Handle with a hexagonal screw and a small cover.

Install the rain Shower head

Step1: Wrap the teflon tape on the thread.
Step2: Clockwise rotation of the main body into the pipe.
Step3: The rain shower head connects to the arm.

Install the handheld shower

Step 1: Use the teflon tape to wrap the screw.then screw the screw nto the water pipe inside he wall directly.

Step 2: Connect the handheld shower and bracket holder with the hose.
Make sure the rubber gaskets inside the hose.

Install the Outlet nozzle

Step 1: Use the teflon tape to wrap the screw.then screw the screw into the water pipe inside he wall directly.

Q & A

Is there a noise problem with the shower valve?

No more water noise: This shower valve has a built-in high-quality check valve to prevent water hammer noise

How deep to install the valve inside the wall?

For the sake of beauty, it is recommended that you install the valve completely into the wall, and the edge of the embedded box is kept flush with the tile surface.

Can | just install it without wrapping teflon tape?

No, it is recommended that you connect teflon tape to each interface to prevent water leakage at the installation interface.

What if | still have problems installing?

You can watch a clear product installation video on our product detail page. You can also send an email to our online customer service at any time. We will solve it together. Our after-sales email is erzhima@outlook.com. Thank you.

CLEARANCE AND MAINTENANCE

How to clean shower head nozzles?
Just rub the nozzles with your finger or a toothbrush to loosen any deposits, and then run hot water for a few minutes

How to keep the faucet appearance smooth and good performance?

1. Clean with water and dry with a soft cotton cloth;
2. Use mild liquid and colorless glass cleaner to remove surface dirt and scale, also you can use the cleaner without grinding function.
3. Do not use detergents, polishing tools, abrasive cloth, paper towels or scrapers to clean the faucet
4. Do not use acid cleaners, insoluble granular detergents, soaps, etc to clean the faucet.

QUALITY ASSURANCE
With our after-sale service, your concern 100% can be resolved following 2 steps, any questions you have regarding our products will be resolved easily.

STEP1: INSTALLATION MANUAL & VIDEO
Our installation manuals and video are available for any needs you should have, from general installation instructions to more specific instructions, depending on the product.

STEP2: QUICK SUPPORT
You can watch a clear product installation video on our product detail page.
You can also send an email to our online customer service at any time.
We will solve it together. Our after-sales email is erzhima@outlook.com.
Thank you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>