Enerwave ZW15SM-N Smart Meter Switch Instruction Manual
- May 15, 2024
- Enerwave
Table of Contents
INSTALLATION NSTRUCTIONS
DESCRIPTION
The ZW 15S M -N by itself is a Single Pole switch. Our unique wiring method combined with Advanced Z-Wave technology allows for multiple switches (requires ZW3K -N ) to control a single Load manually at the devices or remotely from a computer, smart phone or tablet in Real Time . The ZW15SM-N is fully compatible with other Z-Wave devices and it can be added to most Z-Wave compliant controllers.
FEATURES
- Replaces a standard 120VAC, 15Amp wall switch with a technologically advanced switch that can be manually controlled at the device or remotely through the Z-Wave network.
- Set scenes, schedule events (Program ON/OFF times like a timer), and even turn ON/OFF when a motion or door sensor goes off.
- Can be used as a Single Pole switch or 3- Way (Multi-location) with ZW3K-N Auxiliary Switch (sold separately).
- A blue LED night light can be programmed to come on when the load is ON or OFF.
- 3 Interchangeable Color Face Plates included (white, light almond, and black).
- Compatible with CFL, fluorescent, incandescent, and halogen bulbs.
- Measures energy usage of the connected load.
REQUIREMENTS
Z-Wave devices require a connection to a compatible hub. Once the device is properly added to the hub, it can be managed and customized to your needs. Please visit www.enerwaveau t omation.com for a list of compatible hubs. NEUTRAL wire is required.
SPECIFICATIONS
Voltage………………………………………………………………………………………….. 120VAC, 60Hz
Incandescent………………………………………………………………………………………………1000W
Ballast………………………………………………………………………………………………………1200VA
Resistive…………………………………………………………………………………………….1800W(15A)
Motor………………………………………………………………………………………………………… 1/2 HP
Operating Temperature…………………………………………………………………………… 32-104° F
Z- Wave Frequency……………………………………………………………………………… 908.42 MHz
Range……………………………………………………………………………..Up to 100 feet line of sight
……………………between the Wireless Controller and the closest Z-Wave receiver
module.
UPGRADING STANDARD SWITCHES TO Z-WAVE
REPLACING EXISTING SWITCH ES WITH THE ZW15SM-N
Replacing a standard light switch with a smart Z-Wave switch is a simple way
to modernize your home by adding programmable lighting control to your smart
device. The ZW15SM -N Smart Meter Switch enables you to measure the energy
usage of your Lights. When added to a Z-Wave network, the ZW15SM-N reports
real time data to your gateway or controller. It can also display actual
consumption (in W) and the accumulated power used (in kWh) in the user
interface depending on the Hub. Please refer to your Hub manual for specific
instructions on measuring the power.
If you have trouble identifying the wires, STOP and consult with an
Electrician.
WIRING DIRECTIONS
Step 1. Identify all your wires. Label the wires or draw a diagram of
existing wires. Make sure there is a NEUTRAL, HOT, and LOAD wire where the
ZW15SM-N will be installed.
Step 2. Connect the wires according to the Diagram.
- Connect the BLACK wire on switch to the HOT wire.
- Connect the WHITE wire on switch to the NEUTRAL wire.
- Connect the Red wire on switch to the LOAD wire.
- Connect t he GREEN wire on switch to the GROUND wire or green GROUND screw on box.
FCC COMPLIANCE STATEMENT
FCC Grant of Equipment Authorizations of this device and transmitters
installed in this device can be found at FCC website by entering the FCC ID
number on the device.
Caution: C hanges or modifications not expressly approved by the part
responsible for compliance could void the user’s right to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
T his equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
PROGRAMMING
WIRELESS RANGE
This device complies with the Z-Wave standard of open-air, line of sight
transmission distances of 100 feet. Actual performance in a home depends on
the numbers of walls between the remote controller and the destination device,
the type of construction and the number of Z-Wave enabled devices installed in
the control network. Most Z-Wave enabled devices act as signal repeater and
multiple devices result in more possible transmission routes which helps
eliminate ” RF dead-spots.” Use the following chart only as a guide to
maximize the signal range.
Distance of the ZW15S-N (or repeating Z-Wave module) to HUB:
Type of Construction | Wood Frame with Drywall| Brick, Tile or Concrete
Plastic J-Boxes| Metal J-Boxes| Plastic J-Boxes| Metal J-Boxes
Number of Walls or Obstructions| 0**| 100′| 80′| 100′| 80′
1| 70′| 56′| 6()’| 48′
2| 49′| 39′| 36′| 29′
3| 34′| 27′| 21′| 17′
ADVANCED PROGRAMMING
WARNING: Advanced programming is recommended ONLY for experienced
programmers. The ZW15S M -N has customizable features / functions that require
writing codes. Changes to code may cause device to function improperly or to
not function at all.
The following parameters require that you have an advanced controller. Basic
remotes do not have this capability.
All-ON and All-OFF
Depending upon your primary controller, the ZW15SM-N switch can be set to
respond to ALL-ON and ALL-OFF commands in four different ways. Some
controllers may not be able to change the response from its default setting.
Please refer to your controller’s instructions or technical support for
information on whether or not it supports the configuration function and if
so, how to change this setting. The four possible responses for each button
(top or bottom button on switch) are:
-Push button will respond to ALL-ON and the ALL-OFF command (default).
-Push button will not respond to ALL-ON or ALL-OFF commands.
-Push button will respond to the ALL-OFF command but will not respond to the ALL-ON command.
-Push button will respond to the ALL-ON command but will not respond to the ALL-OFF command.
LED Light and Buttons Configuration
By default, one press of the “up” button will turn the Load on and the LED
indicator will turn off. U se ” Command_Class_Configuration ” to configure the
LED indicator to operate in reverse when the button is pressed.
Configuration details
- Parameter 1 (configure LED light state ), default value is 0. Valid values are 0 and 1 with 1 byte.
- Parameter 2 (configure button toggle), default value is 0. Valid values are 0 and 1 with 1 byte.
DEVICE INCLUSION/ EXCLUSION
The process of “Inclusion/ Exclusion” is to Add or Remove the device from the Hub. All Z-Wave devices must be “Included” on he Controller (Hub) before it can be controlled from a smart device. The Hub should be brought physically closer to the device just for the “Inclusion” process (recommended within 10ft). When finished, the Hub and device can be moved back to final installation location. Download the App or log onto the website associated with the Hub you are using and follow their Inclusion/ Exclusion instructions as each Hub’s programming and features are different.
-
During the Inclusion/ Exclusion process, the ON/OFF switch is used for including/ excluding the device.
-
It is best to perform an Exclusion of the device prior to performing an Inclusion.
Step 1. From the Control Panel, go the the device Exclusion page.
o Select “Exclude Device”.
o When prompted, press the “ON” or “OFF” Button on the switch. -
Step 2. Go to the “Add Device” page.
o Select “Include Device”.
o When prompted, press the “ON” or “OFF” Button on the switch.
The primary controller should indicate that the action was successful. If the
controller indicates the action was unsuccessful, please repeat from Step 1 .
Once the switch is part of the network, the same basic procedure is used to
add the switch to groups & scenes or change advanced functions. Refer to the
primary controller’s instructions for details.
Step 3. Follow the On-Screen instructions in the Control Panel on adding
or removing rooms, scenes, other devices, and other functions and features.
OPERATING THE ZW15SM-N
You’re now ready for basic operation of the ZW15SM-N . The switch turns the
Load (Lights) ON/OFF when the ON/OFF rocker switch is pushed. It can also be
operated from your desktop or a smart device such as the iPhone, iPad or any
Android device.
Parameter NO.| Size| Description| Valid Value| Default
Value
---|---|---|---|---
1| 1 Byte| synchronization of load power and LED indicator| 0: Power on, LED
off
1: Power on, LED on| Default=0
8| 1 Byte| Instant Energy Autosend Interval
(send METERREPORT)| 0: not send 1-255: 1-255 Min| Default=0
9| 1 Byte| Instant Energy Autosend Interval
(send SENSOR
MULTILEVEL REPORT)| 0: not send 1-255: 1-255 Min| Default=0
10| 1 Byte| Accumulated Energy
Autosend Interval report
(send METER_REPORT)| 0: not send 1-255: 1-255 Min| Default=0
11| 1 Byte| Enable automatic notifications to associated device whenever there
is a wattage change| 0: Not report
1:Send (METER_REPORT) only
2:Send (SENSOR_MULTI LEVELREPORT) only
3:Send both (METER
REPORT) and (SENSOR MULTILEVEL REPORT)| Default=1
,
12| 1 Byte| Minimum change in wattage report| 0-255: 0.0-25.5W| Default=10
ZW15SM-N
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2
years from the date of purchase. Original receipt or proof of purchase from an
authorized retailer must be presented upon warranty claim. ALL claims must be
verified and approved by Enerwave , Inc. Warranties from other Enerwave
products may vary. This warranty is nontransferable and does not cover normal
wear and tear or any malfunction, failure, or defect resulting from misuse,
abuse, neglect, alteration, modification, or improper installation. To the
fullest extent permitted by the applicable state law, Enerwave shall not be
liable to the purchaser or end user customer of Enerwave products for direct,
indirect, incidental, or consequential damages even if Enerwave has been
advised of the possibility of such damages. Enerwave ’ s total liability under
this or any other warranty, express or implied, is limited to repair,
replacement or refund. Repair, replacement or refund are the sole and
exclusive remedies for breach of warranty or any other legal theory.
Model: ZW 15S M -N
Wireless Home Automation Control
ON/OFF Switch with Smart Meter © 2016 Enerwave Home Automation
WWW.ENERWAVEAUTOMATION.COM
CA, USA
020 7 1600 33
https://manual-hub.com/