iiyama TF1534MC ProLite LCD Monitor User Manual

iiyama TF1534MC ProLite LCD Monitor

Product Information

Specifications

• Brand : iiyama
• Product Type : LCD Monitor
• Language : English
• Website : https://manual-hub.com/

Product Usage Instructions

For Your Safety

Safety Precautions

• WARNING: Stop operating the monitor when you sense trouble. If you notice any abnormal phenomena such as smoke, strange sounds, or fumes, unplug the monitor immediately and contact your dealer or iiyama service center. Further use may be dangerous and can cause fire or electric shock.
• NEVER REMOVE THE CABINET: High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fire or electric shock.
• DO NOT PUT ANY OBJECT INTO THE MONITOR: Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fire, electric shock, or damage.
• INSTALL THE MONITOR ON A FLAT, STABLE SURFACE: The monitor may cause an injury if it falls or is dropped.
• DO NOT USE THE MONITOR NEAR WATER: Do not use where water may be splashed or spilled onto the monitor as it may cause fire or electric shock.
• OPERATE UNDER THE SPECIFIED POWER SUPPLY: Be sure to operate the monitor only with the specified power supply. Use of an incorrect voltage will cause malfunction and may cause fire or electric shock.
• CORRECT USE OF THE AC ADAPTER: Use only the AC Adapter provided by iiyama. Any deviation from this by using another type of adapter may result in damage to the accessory and the monitor by fire or electric shock.

Operating the Monitor

• Adjustment Menu Contents
  The adjustment menu allows you to customize various settings on your monitor. Refer to the user manual’s “Adjustment Menu Contents” section (page

14. for detailed information on each setting.

• Screen Adjustments
  The screen adjustment feature enables you to modify the screen’s brightness, contrast, color temperature, and other visual settings. Please refer to the user manual’s “Screen Adjustments” section (page 18) for step-by- step instructions on adjusting these settings.

• Power Management Feature
  The power management feature helps conserve energy by automatically turning off the monitor or putting it into a low-power sleep mode when it is idle for a certain period. To learn how to enable or customize this feature, refer to the user manual’s “Power Management Feature” section (page 21).

Troubleshooting

• Troubleshooting
  If you encounter any issues with your monitor’s performance or functionality, consult the user manual’s “Troubleshooting” section (page 22) for a list of common problems and their possible solutions.

• Recycling Information

• Recycling Information
  We recommend recycling used products. Please contact your dealer or iiyama service center for appropriate recycling information. You can also visit the iiyama website at http://www.iiyama.com to access recycling information specific to different countries.

Appendix

Appendix
Refer to the user manual’s “Appendix” section (page 24) for additional information, including technical specifications, troubleshooting flowcharts, and other useful resources.

FAQ

• Q: Where can I obtain recycling information for my used monitor?
  A: You can contact your dealer or iiyama service center for appropriate recycling information. Alternatively, you can visit the iiyama website at http://www.iiyama.com and access the recycling information specific to different countries.

• Q: Can I adjust the screen settings on my monitor?
  A: Yes, you can customize various screen settings such as brightness, contrast, and color temperature. Please refer to the user manual’s “Screen Adjustments” section (page 18) for detailed instructions on how to adjust these settings.

• Q: What should I do if I notice any abnormal phenomena or sense trouble while using the monitor?
  A: If you notice any abnormal phenomena such as smoke, strange sounds, or fumes, immediately unplug the monitor and contact your dealer or iiyama service center. Continuing to use the monitor under such circumstances may be dangerous and can cause fire or electric shock.

• Q: Can I use a different AC adapter for my monitor?
  A: No, it is recommended to use only the AC Adapter provided by iiyama. Using a different type of adapter may result in damage to the accessory and the monitor, posing a risk of fire or electric shock.

USER MANUAL
Pro Lite
LCD Monitor

• ProLite TF1534MC
• ProLite TF1734MC
• ProLite TF1934MC

Thank you very much for choosing the iiyama LCD monitor.
We recommend that you take a few minutes to read this comprehensive manual carefully before installing and switching on the monitor. Please keep this manual in a safe place for your future reference.

Dear user, we congratulate you on the purchase of your iiyama LCD.
For details on warranty and locally used pixel policies that apply directly after installation of your product please check the liyama website.
To report a fault, please contact your local support centre found at www.iiyama.com/ service

Things to check before you call the ilyama information line

• if the power cable is connected securely and turned on?
• if the display has been turned on?
• if the signal cable is connected securely and the correct input selected?
• if the computer has been restarted with the display connected?
• if the graphics card is correctly installed with the latest drivers possible?
• if the correct native resolution has been selected via ‘Display Properties?
• If the R/G/B signal configuration is correct?
• if the displays On Screen Menu is shown?
• if the correct brightness and contrast settings have been set?
• if given display tolerances and compatibility have been considered?
• if via the On Screen Menu you have performed a Factory Reset/Recall?

Before reporting the screen defect, please prepare the following information/evidence

• [model number*
• purchase receipt and serial number*
• name and address for collection
• telephone/fax number, for availability during the day
• convenient collection date (date, time)
• short description of the defect

Important Note
If there is no fault found in the collected equipment after inspection, the transferring party shall incur charges for transport and administration.
If you have checked all of the above and there is still no picture, call our information line for assistance in your country.

see the identitication plate on the back of the case.
www.liyama.com

CE MARKING DECLARATION OF CONFORMITY
This LCD monitor complies with the requirements of the EC/EU Directive 2014/30/EU “EMC Directive”, 2014/35/EU “Low Voltage Directive”, 2009/125/EC “ErP Directive” and 2011/65/EU “RoHS Directive”.
The electro-magnetic susceptibility has been chosen at a level that gives correct operation in residential areas, business and light industrial premises and small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.
IIYAMA CORPORATION : Wijkermeerstraat 8, 2131 HA Hoofddorp, The Netherlands
Model No. : PLTF1534, PLTF1734, PLTF1934

We recommend recycling of used product. Please contact your dealer or iiyama service center. Recycle information is obtained via the Internet, using the address: http://www.iiyama.com
You can access the Web page of different countries from there.

• We reserve the right to change specifications without notice.
• All trademarks used in this user manual are the property of their respective owners.

FOR YOUR SAFETY

SAFETY PRECAUTIONS
WARNING

• STOP OPERATING THE MONITOR WHEN YOU SENSE TROUBLE
  If you notice any abnormal phenomena such as smoke, strange sounds or fumes, unplug the monitor and contact your dealer or iiyama service center immediately. Further use may be dangerous and can cause fi re or electric shock.

• NEVER REMOVE THE CABINET
  High voltage circuits are inside the monitor. Removing the cabinet may expose you to the danger of fi re or electric shock.

• DO NOT PUT ANY OBJECT INTO THE MONITOR
  Do not put any solid objects or liquids such as water into the monitor. In case of an accident, unplug your monitor immediately and contact your dealer or iiyama service center. Using the monitor with any object inside may cause fi re, electric shock or damage.

• INSTALL THE MONITOR ON A FLAT, STABLE SURFACE
  The monitor may cause an injury if it falls or is dropped.

• DO NOT USE THE MONITOR NEAR WATER
  Do not use where water may be splashed or spilt onto the monitor as it may cause fi re or electric shock.

• OPERATE UNDER THE SPECIFIED POWER SUPPLY
  Be sure to operate the monitor only with the specifi ed power supply. Use of an incorrect voltage will cause malfunction and may cause fi re or electric shock.

• CORRECT USE OF THE AC ADAPTER
  Use only the AC Adapter provided by iiyama. Any deviation from this by using another type of adapter may result in damage to the accessory and the monitor by fi re or electric shock.

• DO NOT DISASSEMBLE THE AC ADAPTER
  Disassembling the AC Adapter may expose you to the danger of fi re or electric shock.

• PROTECT THE CABLES
  Do not pull or bend the AC adapter, the power cable and signal cable. Do not place the monitor or any other heavy objects on the cables. If damaged, the cables may cause fi re or electric shock.

• ADVERSE WEATHER CONDITIONS
  It is advisable not to operate the monitor during a heavy thunder storm as the continual breaks in power may cause malfunction. It is also advised not to touch the plug in these circumstances as it may cause electric shock.

CAUTION

• INSTALLATION LOCATION
  Do not install the monitor where sudden temperature changes may occur, or in humid, dusty or smoky areas as it may cause fi re, electric shock or damage. You should also avoid areas where the sun shines directly on the monitor.

• DO NOT PLACE THE MONITOR IN A HAZARDOUS POSITION
  The monitor may topple and cause injury if not suitably located. Please also ensure that you do not place any heavy objects on the monitor, and that all cables are routed such that children may not pull the cables and possibly cause injury.

• MAINTAIN GOOD VENTILATION
  Ventilation slots are provided to keep the monitor from overheating. Covering the slots may cause fi re. To allow adequate air circulation, place the monitor at least 10 cm (or 4 inches) from any walls. Do not remove the tilt stand when operating the monitor. Ventilation slots on the back of the cabinet will be blocked and the monitor may overheat if the stand is removed. This may cause fi re or damage. Operating the monitor on its back, side, upside down or on a carpet or any other soft material may also cause damage.

• DISCONNECT THE CABLES WHEN YOU MOVE THE MONITOR
  When you move the monitor, turn off the power switch, unplug the monitor and be sure the signal cable is disconnected. If you do not disconnect them, it may cause fi re or electric shock.

• UNPLUG THE MONITOR
  If the monitor is not in use for a long period of time it is recommended that it is left unplugged to avoid accidents.

• HOLD THE PLUG WHEN DISCONNECTING
  To disconnect the AC adapter, the power cable or signal cable, always pull it by the plug. Never pull on the cable itself as this may cause fi re or electric shock.

• DO NOT TOUCH THE PLUG WITH WET HANDS
  Pulling or inserting the plug with wet hands may cause electric shock.

• WHEN YOU INSTALL THE MONITOR ON YOUR COMPUTER
  Be sure the computer is strong enough to hold the weight of the monitor, otherwise, you may damage your computer.

• REMARK FOR 24/7 USAGE
  This product is not specifi cally designed for 24/7 usage in all environments.

OTHERS

ERGONOMIC RECOMMENDATIONS
To eliminate eye fatigue, do not operate the monitor against a bright background or in a dark room. For optimal viewing comfort, the monitor should be just below eye level and 40-60 cm (16-24 inches) away from your eyes. When using the monitor over a prolonged time, a ten minute break every hour is recommended as looking at the screen continuously can cause eye strain.
2 FOR YOUR SAFETY

SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitors and do not indicate a problem.
NOTE

• When you fi rst turn on the LCD monitor, the picture may not fi t in the display area because of the type of computer that is used. In this case, adjust the picture position to the correct position.
• You may fi nd slightly uneven brightness on the screen depending on the desktop pattern you use.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for some hours.

CUSTOMER SERVICE
NOTE
If you have to return your unit for service and the original packaging has been discarded, please contact your dealer or iiyama service center for advice or replacement packaging.

CLEANING

• WARNING If you drop any materials or liquids such as water into the monitor when cleaning, unplug the power cable immediately and contact your dealer or iiyama service center.

• NOTE   To protect the Touch screen surface, do not scratch or rub the screen with a hard object.

• Never use any of the following strong solvents. These will damage the cabinet and the Touch screen surface.
  Abrasive cleaner Wax Solvent

• Touching the cabinet with any product made from rubber or plastic for a long time may cause degeneration or loss of paint on the cabinet.

CABINET Stains can be removed with a cloth lightly moistened with a mild detergent solvent.
Then wipe the cabinet with a soft dry cloth.
TOUCH SCREEN Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50/50 mixture of water and IPA(ISO-propyl- alcohol). Don’t use acid or alkaline solvent to clean the surface of the panel (or screen).

BEFORE YOU OPERATE THE MONITOR

FEATURES

• Supports Resolutions up to 1024 × 768 : ProLite TF1534MC

• Supports Resolutions up to 1280 × 1024 : ProLite TF1734MC / ProLite TF1934MC

• High Contrast 700 :1 (Typical) / Brightness 330cd/m2 ( Typical : with Touch panel) : ProLite TF1534MC

• High Contrast 1000 :1 (Typical) / Brightness 350cd/m2 ( Typical : with Touch panel) : ProLite TF1734MC / ProLite TF1934MC

• Digital Character Smoothing

• Automatic Set-up

• Plug & Play VESA DDC2B Compliant
  Windows® XP/Vista/7/8/8.1/10 Compliant

• Power Management (VESA DPMS Compliant)

• VESA Mounting Standard (100mm×100mm) Compliant

• IP65 Standard Compliant (Only front face)

• Anti fingerprint finish

Windows8/8.1/10 touch environment
Basic touch operations can be performed under Windows 8/8.1/10.
However, please be informed that full touch functionality and normal operational performance are not guaranteed.

CHECKING THE CONTENTS OF THE PACKAGE
The following accessories are included in your package. Check to see if they are enclosed with the monitor. If anything is missing or damaged, please contact your local iiyama dealer or regional iiyama offi ce.

•  Power Cable*1
•  DisplayPort Cable
• L-Bracket (2pairs)
• Touch Panel Driver Disk (CD-ROM)*2
• Quick Start Guide
• AC Adapter*1
• USB Cable
• Bracket Screw (M4×8 8pcs)
• MOUNTING KITS User manual
• HDMI Cable
• Cable Cover Screw (M3x6 1pcs)
• Safety Guide

CAUTION

1. TO USERS IN 120V AREA
   The rating of the Power Cable enclosed in 120V area is 10A/125V. If you are using a power supply higher than this rating, then a power cable with a rating of 10A/250V must be used. However, all guarantees and warranties are void for any
   problems or damage caused by a power cable or AC adapter not supplied by iiyama.

2. Applicable AC Adapter
   AC Adapter Type Name : ADP-50YH B (DELTA ELECTRONICS, INC.)

3. An approved power cable greater or equal to H05VVF, 3G, 0.75mm2 must be used.
   *2 This CD-ROM contains the touch screen driver software.
   Install the Touch Panel Driver Disk after connecting the computer to the monitor with USB Cable. For the details, see Readme fi le in the Touch Panel Driver Disk.

4. BEFORE YOU OPERATE THE MONITOR

WALL MOUNTING **

**

WARNING
When you use with the wall mounting, in consideration of thickness of the mounting stage, tighten the M4 Screw with washer which “L” length is 8mm to fasten the monitor. Using the screw longer than this may cause electric shock or damage because it may contact with the electrical parts inside the monitor.

BUILT-IN EQUIPMENT
WARNING
This product is not designed for the purpose of being used in high temperature environment.
If the product is placed in an external cabinet, you need to design cooling fans and vents to keep the temperature low enough to fit in the product temperature specifi cation.

ROTATING THE DISPLAY
It is designed to be compatible in landscape mode.

CONTROLS AND CONNECTORS

• Menu Button (MENU)*

• Scroll Up / Brightness Button ( )*

• Scroll Down / Contrast Button ( )*

• Select Button (SELECT)*

• Power Switch ( )*

• Power Indicator
  NOTE Green : Normal operation Orange: Power Management

• USB Connector (USB)

• Remote Control Touch V01 Connector (RJ11) VGA Connector (VGA)

• HDMI Connector (HDMI)

• DisplayPort Connector (DP)

• Connector for AC Adapter( : Direct current) (DC)

Remote Control Touch V01 is optional.

SPECIAL NOTES
L-Brackets and screws are necessary to install an open frame monitor.

CAUTION

•  The L-Brackets are designed to be mounted to specific wall types and hardware, in accordance with the installation instructions supplied with the Mounting Kit.
•  Using L-Bracket or screws other than those specified in the installation instructions may damage the monitor.

1. As shown in figure below, tighten Bracket A to B using the screws supplied (2pairs of 2 pcs).
2. Depending on the monitor orientation (portrait or landscape) you choose, mount the L-Brackets to the left and right hand sides or the upper and lower sides of the monitor and tighten them with screws supplied (2 pairs of 2 pcs).

NOTE

•  You will need a screwdriver to mount the L-Bracket.

•  L-Brackets and screws are necessary to install an open frame monitor. For details regarding open frame monitor temperature and humidity operating conditions, see the User Manual on IIYAMA website. http://www.iiyama.com.
  < ProLite TF1534MC-B6X>

• The position of the L-bracket can be either 1.3 mm or 40.7 mm from the front of the monitor depending on which screw holes you choose for mounting it.
  < ProLite TF1734MC-B6X / ProLite TF1934MC-B6X>

• The position of the L-bracket can be either 2.9 mm or 44.9 mm from the front of the monitor depending on which screw holes you choose for mounting it.

CONNECTING YOUR MONITOR

1. Ensure that both the computer and the monitor are switched off .
2. Connect the computer to the monitor with the signal cable.
3. Connect the computer to the monitor with the USB Cable.
4. Connect the monitor cable to the Remote Control Touch V01 (option), if necessary.
5. Connect the AC Adapter to the monitor and the Power Cable to the AC Adapter fi rst and then connect to the power source.
6. Turn on your monitor and computer.

NOTE

• The signal cables used for connecting the computer and monitor may vary with the type of computer used. An incorrect connection may cause serious damage to both the monitor and the computer. The cable supplied with the monitor is for a standard connector. If a special cable is required please contact your local iiyama dealer or regional iiyama office.
• For connection to Macintosh computers, contact your local iiyama dealer or regional iiyama office for a suitable adaptor.
• Make sure you tighten the finger screws at each end of the Signal Cable.
• The Class I pluggable equipment Type A must be connected to protective earth.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.

VGA cable is not supplied with the monitor. If you use low quality VGA cable, it may cause a result of electro-magnetic interference. Please contact the iiyama Support Centre in your country if you wish to connect the monitor via the VGA input.

[Fitting and Removal of Cable Cover]
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched. Lay the monitor flat on a table with front face down.
< Removal >
Remove the cable cover as shown in Step1.
< Fitting >
Connect the cables, as shown in Step2, place the cable cover and fi x it fi rmly using a screw.

COMPUTER SETTING

• Signal Timing
  Change to the desired signal timing listed on page 28: COMPLIANT TIMING.

• Windows XP/Vista/7/8/8.1/10 Plug & Play
  The iiyama LCD monitor complies with DDC2B of VESA standard. The Plug & Play function runs on Windows XP/Vista/7/8/8.1/10 by connecting the monitor to DDC2B compliant computer with the Signal Cable supplied.
  For installation on Windows XP: The monitor Information File for iiyama monitors may be necessary for your computer and obtained via the Internet, using the address: http://www.iiyama.com

NOTE

• For additional information on how to download the driver for your touch screen monitor, please access the internet site noted above.

• Monitor Drivers are not required in most cases for Macintosh or Unix operating systems. For further information, please contact your computer dealer fi rst for advice.

•  Procedure for turning ON the Power Switch
  Turn ON the monitor fi rst, and then the computer.

• Touch screen driver software
  Touch screen driver software and system may not start when you start your computer while touching the screen.
  Touch screen driver software may not run due to the power saving function depending on the BIOS of your computer. In this case, set the power saving function to off .

• TOUCH support operation system
  Microsoft Windows XP (64 bit and 32 bit)  Microsoft Windows Vista (64 bit and 32 bit)
  Microsoft Windows 7 (64 bit and 32 bit)    Microsoft Windows 8 / 8.1 / 10 (64 bit and 32 bit)
  Microsoft Windows CE 2.13 / 3.0, net 6.0     Mac OS9.x, OS X V10.4/10.5/10.6 & above
  Linux (Kernel2.4, 2.6x) & above     Not support earlier versions.

| Windows8/8.1/10| Windows75| Windows74| Vista| XP
---|---|---|---|---|---
Default mouse1| | | | |
Touch digitizer2| | | | |
Windows7 gestures3| | | | |
| 2K| Windows CE| XP Embedded| Mac OS9,OSX| Linux
---|---|---|---|---|---
Default mouse1| | | | |
Touch digitizer2| | | | |
Windows7 gestures3| | | | |

• 1 Default mouse (click, drag, double-click and right-click)
• 2 Touch digitizer (click, drag /selection, double-click, right-click, fl ick and visual feedback)
• 3 Digitizer with Windows7 touch gestures
• 4 Windows 7 – Starter and Home Basic version
• 5 Windows 7 – Home Premium, Professional, Enterprise and Ultimate versions

OPERATING THE MONITOR

To create the best picture, your iiyama LCD monitor has been preset at the factory with the COMPLIANT TIMING shown on page 28. You are also able to adjust the picture by following the button operation shown below. For more detailed adjustments, see page 18 for SCREEN ADJUSTMENTS.

1. Press the MENU Button to start the On Screen Display feature. There are additional Menu items which can be switched by using the Buttons.
2. Select the Menu item which contains the adjustment icon relating to the adjustment you want to make. Use the SELECT Button to highlight the desired adjustment icon.
3. Use the Buttons to make the appropriate adjustment or setting.
4. Press the MENU Button to leave the menu, and the settings you just made would be automatically saved.
   For example, to correct for vertical position, select Menu item of Picture. Then, select V-Position by using the SELECT Button.
   Use the Buttons to change the vertical position settings. The vertical position of the overall display should be changing accordingly while you are doing this.

Press the MENU Button lastly, it ends, all changes are saved in the memory.

NOTE

• When button operations are aborted during adjustment, On-Screen Display disappears when the time set for the OSD Timeout has passed.
• MENU button can be used to return previous menu item.
• Any changes are automatically saved in the memory when the On Screen Display disappears. Turning off the power should be avoided while using the Menu.
• Adjustments for H/V-Position, Clock and Phase are saved for each signal timing. Except for these adjustments, all other adjustments have only one setting which applies to all signal timings.

Direct

LOCK MODE
Simultaneously press the MENU button and the button when an image is displayed through VGA, HDMI or DisplayPort.
The OSD menu is not displayed when the OSD is locked. Press the MENU button and the button simultaneously again.
The following OSD menu is displayed.

TOUCH FUNCTION DISABLE:
ON : Pressing and holding of the MENU Button and the SELECT Button at the same time when the Menu is not displayed, massage “TOUCH DISABLE” will appear on the top right corner.
OFF : Pressing and holding of the MENU Button and the SELECT Button at the same time for about 5 seconds when the Menu is not displayed, till “TOUCH DISABLE” disappears.

ADJUSTMENT MENU CONTENTS

  Picture| | | |
---|---|---|---|---
Adjustment Item| Problem / Option| | Button to Press
Contrast| Direct| Too dull Too intense
Brightness1| Direct| Too dark Too bright
H-Position4| left Too right
V-Position4| low Too high
Phase2,4| To correct flickering text or lines
Clock2,4| Too narrow Too wide
Auto Adjust3,4| Adjust H/V-Position, Clock and Phase automatically.

• 1 Adjust the Brightness when you are using the monitor in a dark room and feel the screen is too bright.
• 2 See page 18 for SCREEN ADJUSTMENTS.
• 3 For best results, use the Auto Adjust in conjunction with the adjustment pattern. See page 18 for SCREEN ADJUSTMENTS.
• 4 Only Analog Input.

Direct
You can skip the Menu items and directly display an adjustment scale by using the following button operations.

Contrast : Press the Button when the Menu is not displayed.
Brightness : Press the Button when the Menu is not displayed.

  Advanced|

|

---|---|---
Adjustment Item| Problem / Option| | Button to Press
Color Temp| 5500| Greenish white
6500| Reddish white
7500| Yellowish white
9300| Bluish white
User| Red| Too weak Too strong
Green
Blue
Sharpness|

• You can change the picture quality from 0 to 100 (soft to sharp).
• Press the  Button to change the picture quality in
• numerical order. Press the  Button to change the  picture quality in reverse numerical order.
• Adjust the picture quality at resolutions of less 1024 x 768(ProLite TF1534MC) / 1280 x 1024(ProLite TF1734MC/ProLite TF1934MC). You can change the picture quality.

OSD

Adjustment Item| | Problem / Option

Button to Press

OSD Timeout| | You can set the OSD display duration time between 5 and 60 seconds.

OSD Position| | You can set the OSD position.
User (Upper left / Lower left / Upper right / Lower right / Center)
OSD H-Position| | OSD is too left
OSD is too right
OSD V-Position| | OSD is too low
OSD is too high

automatically.
VGA| Select the analog input.
HDMI| Select the digital(HDMI) input.
DP| Select the digital(DisplayPort) input.
OSD is too right
OSD is too right| Displays information regarding the current input signal coming from the graphic card in your computer.

NOTE
See your graphic card user guide for more information about changing the resolution and refresh.

OSD is too right| This function is for service personnel only and therefore the operation is not available.

Direct
You can skip the Menu items and directly display an option setting screen by using the following button operations.
Source Select : Pressing and holding of the SELECT Button for about 5 seconds when the Menu is not displayed.
By pressing the SELECT Button during power management mode, the Source Selected menu will be displayed.

SCREEN ADJUSTMENTS

Adjust the image by following the procedure below to get the desired picture when selecting Analog input.

• The screen adjustments described in this manual are designed to set image position and minimize flicker or blur for the particular computer in use.
• ProLite TF1534MC is designed to provide the best performance at resolution of 1024 × 768, but can not provide the best at resolutions of less than 1024 × 768 because the picture is automatically stretched to fi t the full screen. It is recommended to operate at resolution of 1024 × 768 in normal use.
• ProLite TF1734MC and ProLite TF1934MC are designed to provide the best performance at resolution of 1280 × 1024, but can not provide the best at resolutions of less than 1280 × 1024 because the picture is automatically stretched to fi t the full screen. It is recommended to operate at resolution of 1280 × 1024 in normal use.
• Displayed text or lines will be blurred or irregular in thickness when the picture is stretched due to the screen enlargement process.
• It is preferable to adjust the image position and frequency with the monitor controls, rather than the computer software or utilities.
• Perform adjustments after a warm-up period of at least thirty minutes.
• Additional adjustments may be required after the Auto Adjust depending on the resolution or signal timing.
• The Auto Adjust may not work correctly when displaying the picture other than the screen adjustment pattern. In this case, manual adjustments are required.

There are two ways to adjust the screen. One way is automatic adjustment forH/V-Position, Clock and Phase. The other way is performing each adjustment manually.
Perform the Auto Adjust first when the monitor is connected to a new computer, or resolution is changed. If the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust, manual adjustments are required. Both adjustments should be made by using the screen adjustment pattern (Test.bmp) obtained via the IIYAMA web site (http://www.iiyama.com).
Adjust the image by following the procedure below to get the desired picture.
This manual explains adjustment under Windows® OS.

1. Display the picture at the optimum resolution.

2. Enter the Test.bmp (screen adjustment pattern) to wallpaper.
   NOTE
   

   • Consult the appropriate documentation for doing this.
   • Set the display position to center in the wallpaper setting dialogue box. If you use Microsoft® PLUS! 95/98 cancel the setting of “Stretch desktop wallpaper to fit the screen”.

3. Press the SELECT Button. (Auto Adjust)

4. Adjust the image manually by following procedure below when the screen has a fl icker or blur, or the picture does not fi t in the display area after performing the Auto Adjust.

5. Adjust the V-Position so that the top and bottom of the picture frame will fi t to the display area.

6. Adjust the H-Position so that the left side of the picture frame will move to the left edge of the display area.

   •  Stretch the right side of the picture frame to the right edge of the display area by adjusting the Clock. NOTE
   • When the left side of the picture frame moves apart from the left edge of the display area during the Clock adjustment, adjust steps 1) and 2).
   • Another way to make the Clock adjustment is to correct the vertical wavy lines in the zebra pattern.
   • The picture may flicker during the Clock, H/V-Position adjustment.
   • In case the picture frame is bigger or smaller than the data display area after the Clock adjustment, repeat steps from .

7. Adjust the Phase to correct horizontal wavy noise, flicker or blur in the zebra pattern. NOTE

   •  In case the strong flicker or blurs remain on a part of the screen, repeat steps and because the Clock may not be adjusted correctly. If the flicker or blurs still remain, set the refresh rate of computer to low (60Hz) and repeat steps from again.
   • Adjust the H-Position after the Phase adjustment if the horizontal position moves during the adjustment.

8. Adjust the Brightness and Color to get the desired picture after you complete the Clock and Phase adjustments.
   Put back your favorite wallpaper.

POWER MANAGEMENT FEATURE

When your computer is not in use, the power management feature will automatically reduce the power consumption of your monitor.
To use the feature, the monitor needs to be connected to a VESA DPMS compliant computer. There is a power management step the monitor takes as described below. The power management function, including any timer settings is configured by the operating system. Check your operating system manual for information on how this can be configured.
Power Management Mode
When the H-sync signal / V-sync signal / H and V sync signals from the computer are off , the monitor enters into Power Management Mode which reduces the power consumption to less than 2W. The screen becomes dark. From Power Management Mode, the image reappears in several seconds when either the keyboard or the mouse are touched again.

NOTE

• Even when using the power management mode, the monitor consumes electricity. Turn off the Power Switch whenever the monitor is not in use, during the night and weekends, to avoid unnecessary power consumption.
• It is possible that the video signal from the computer may be on while the H or V sync signal is missing. In this instance, the POWER MANAGEMENT feature may not work properly.

TROUBLE SHOOTING

If the monitor fails to operate correctly, please follow the steps below for a possible solution.

1. Perform the adjustments described in OPERATING THE MONITOR, depending on the problem you have. If the monitor does not get a picture, skip to 2.
2. Consult the following items if you cannot fi nd an appropriate adjustment item in OPERATING THE MONITOR or if the problem persists.
3. If you are experiencing a problem which is not described below or you cannot correct the problem, discontinue using the monitor and contact your dealer or iiyama service center for further assistance.

Problem                                         Check

1.  The picture does not appear.                     The AC Adapter is firmly seated in the connector.
   (Power indicator does not light up.)         The Power Cable is firmly seated in the socket of the AC Adapter.
   The Power Cable is firmly seated in the socket.
   The Power Switch is turned ON.
   The AC socket is live. Please check with another piece of equipment.
   (Power indicator is green.)                          If  the blank screen saver is in active mode, touch the keyboard or the mouse.
   Increase the Contrast and/or Brightness.
   The computer is ON.
   The Signal Cable is properly connected.
   The signal timing of the computer is within the specification of the monitor.
   (Power indicator is orange.)                       If the monitor is in power management mode, touch the keyboard or the mouse.
   The computer is ON.
   The Signal Cable is properly connected.
   The signal timing of the computer is within the specification of the monitor.

2. The screen is not synchronized.                 The Signal Cable is properly connected.
   The signal timing of the computer is within the specification of the monitor.
   The video output level of the computer is within the specification of the monitor.

3. The screen position is not in the center.   The signal timing of the computer is within the specification of the monitor.

4. The screen is too bright or too dark.         The video output level of the computer is within the specification of the monitor.

5. The screen is shaking.                                   The power voltage is within the specification of the monitor.
   The signal timing of the computer is within the specification of the monitor.

6. The touch screen shows no response.        The USB Cable is fi rmly seated in the socket.
   Touch screen driver software is installed.

7. The touch position does not deviate.        The calibration function set up correctly.

RECYCLING INFORMATION
For better environment protection please don’t dispose your monitor. Please visit our web site: www.iiyama.com for monitor recycling.

APPENDIX

Design and specifi cations are subject to change without prior notice.

SPECIFICATIONS : ProLite TF1534MC-B6X

LCD
Panel| Panel technology| TN
Size| Diagonal: 15″ (38cm)
Pixel pitch| 0.297mm H × 0.297mm V
Brightness| 370cd/m2 ( Typical : without Touch panel), 330cd/m2 (Typical: with Touch panel)
Contrast ratio| 700 : 1 (Typical)
Viewable angle| Horizontal : 170 degrees, Vertical: 160 degrees (Typical)
Response time| 8ms (Black, White, Black Typical)
Display Colors| Approx.16.2M
Sync Frequency| Horizontal : 31.4-60.0kHz, Vertical: 50-75Hz
Maximum Resolution| 1024 × 768, 0.8 MegaPixels
Input Connector| VGA, HDMI, DisplayPort
Plug & Play| VESA DDC2BTM
Input Sync Signal| Separate sync : TTL, Positive or Negative
Input Video Signal| Analog : 0.7Vp-p (Standard), 75W, Positive Digital: HDMI, DisplayPort
Maximum Screen Size| 304.0mm W × 228.0mm H / 12.0″ W × 9.0″ H
Power Source| 12VDC, 2.5A
AC Adapter (accessory)| Input: 100-240VAC 50/60Hz
Power Consumption*1| 9W typical, Power management mode: 2W maximum
Dimensions / Net Weight|

• 337.5 × 265.5 × 44.5mm / 13.3 × 10.5 × 1.7″ (W×H×D)
• 2.7kg / 5.9lbs (Excluding the AC Adapter)

Environmental Considerations|

• Operating : Temperature    0 to 40°C / 32 to 104°F Humidity        20 to 80% (No condensation)
• Storage : Temperature -20 to 60°C / -4 to 140°F Humidity          10 to 90% (No condensation)

Approvals| CB, CE, TÜV-Bauart, CU, cULus, IP65*2

NOTE

1. 1 USB peripherals is not connected.
2. *2 IP65 Standard Compliant : Only front face

LCD
Panel| Panel technology| TN
Size| Diagonal: 17″ (43cm)
Pixel pitch| 0.264mm H × 0.264mm V
Brightness| 350cd/m2 (Typical: without Touch panel), 300cd/m2 (Typical: with Touch panel)
Contrast ratio| 1000 : 1 (Typical)
Viewable angle| Horizontal : 170 degrees, Vertical: 160 degrees (Typical)
Response time| 5ms (Black, White, Black Typical)
Display Colors| Approx.16.7M
Sync Frequency| Horizontal: 31.4-80.0kHz, Vertical: 50-75Hz
Maximum Resolution| 1280 × 1024, 1.3 MegaPixels
Input Connector| VGA, HDMI, DisplayPort
Plug & Play| VESA DDC2BTM
Input Sync Signal| Separate sync : TTL, Positive or Negative
Input Video Signal| Analog: 0.7Vp-p (Standard), 75W, Positive Digital: HDMI, DisplayPort
Maximum Screen Size| 338.0mm W × 270.5mm H / 13.3″ W × 10.6″ H
Power Source| 12VDC, 2.5A
AC Adapter (accessory)| Input: 100-240VAC 50/60Hz
Power Consumption*1| 13W typical, Power management mode: 2W maximum
Dimensions / Net Weight|

• 369.0 × 307.0 × 47.5mm / 14.5 × 12.1 × 1.9″ (W×H×D)
• 3.6kg / 7.9lbs (Excluding the AC Adapter)

Environmental Considerations|

• Operating: Temperature    0 to 40°C / 32 to 104°F Humidity       20 to 80% (No condensation)
• Storage :  Temperature    -20 to 60°C / -4 to 140°F Humidity 10 to 90% (No condensation)

Approvals| CB, CE, TÜV-Bauart, CU, cULus, IP65*2

NOTE

1. 1 USB peripherals is not connected.
2. *2 IP65 Standard Compliant : Only front face

LCD
Panel| Panel technology| IPS
Size| Diagonal: 19″ (48cm)
Pixel pitch| 0.294mm H × 0.294mm V
Brightness| 350cd/m2 (Typical: without Touch panel), 300cd/m2 (Typical: with Touch panel)
Contrast ratio| 1000 : 1 (Typical)
Viewable angle| Horizontal: 178 degrees, Vertical: 178 degrees (Typical)
Response time| 14ms (Gray to Gray)
Display Colors| Approx.16.7M
Sync Frequency| Horizontal: 31.4-80.0kHz, Vertical: 50-75Hz
Maximum Resolution| 1280 × 1024, 1.3 MegaPixels
Input Connector| VGA, HDMI, DisplayPort
Plug & Play| VESA DDC2BTM
Input Sync Signal| Separate sync: TTL, Positive or Negative
Input Video Signal| Analog: 0.7Vp-p (Standard), 75W, Positive Digital: HDMI, DisplayPort
Maximum Screen Size| 376.5mm W × 301.1mm H / 14.8″ W × 11.9″ H
Power Source| 12VDC, 2.5A
AC Adapter (accessory)| Input: 100-240VAC 50/60Hz
Power Consumption*1| 21W typical, Power management mode: 2W maximum
Dimensions / Net Weight|

• 416.0 × 344.0 × 46.5mm / 16.4 × 13.5 × 1.8″ (W×H×D)
• 4.4kg / 9.7lbs (Excluding the AC Adapter)

Environmental Considerations| Operating: Temperature    0 to 40°C / 32 to 104°F Humidity 20 to 80% (No condensation)
Storage: Temperature    -20 to 60°C / -4 to 140°F Humidity 10 to 90% (No condensation)
Approvals| CB, CE, TÜV-Bauart, CU, cULus, IP65*2

NOTE

1. 1 USB peripheral is not connected.
2. *2 IP65 Standard Compliant: Only front face

DIMENSIONS: ProLite TF1534MC

DIMENSIONS: ProLite TF1734MC

DIMENSIONS: ProLite TF1934MC

DIMENSIONS : L-BRACKET

COMPLIANT TIMING

NOTE * Not compliant to ProLite TF1534MC.

References

• iiyama
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>