SUNCO 27W-40W-67W-80W Full Cutoff Wall Pack Installation Guide
- June 17, 2024
- SUNCO
Table of Contents
SUNCO 27W-40W-67W-80W Full Cutoff Wall Pack
Product Information
Specifications:
- Installation: Wall Mount
- Power Supply: Universal voltage driver (60 Hz)
- Photocell: Compatible
- Cleaning: Non-abrasive glass cleaning solution
Product Usage Instructions
Mounting to a Wall:
- Open the Back Box by loosening the Locking Screw.
- Verify and remove any necessary Gasket material where the Back Box will mount.
- Knock-out Back Box material for the desired mounting location.
- Securely mount the Back Box to the Junction Box using hardware supplied by others.
- Connect the electrical connections with the fixture wiring.
- Seal the Back Box to the Housing by pushing on the front of the Housing while tightening the Locking Screw. Ensure that the screw is fully seated in the Housing Recess. Make sure the wiring remains within the Back Box and that the wires do not get pinched. Using a silicone rubber will ensure a watertight seal.
- If the light output angle needs to be adjusted, loosen the screw to rotate the fixture to the desired light output angle. Once the desired angle is achieved, tighten the screw.
- To ensure a waterproof seal, apply weatherproof silicone sealant around the edge of the wall mounting box. This is especially important with an uneven wall surface. Also, silicone all plugs and unused conduit entries.
On-Off Wiring:
Universal voltage driver permits operation at 60 Hz, except for fixtures
factory ordered with a 120-277VAC (PO).
- Connect the BLACK fixture lead to the (+) LINE supply lead.
- Connect the WHITE fixture lead to the (-) COMMON supply lead.
- Connect the Yellow Green wire from the fixture to the supply ground.
Photocell Installation:
- Install the photocell and wire it as per the provided diagram.
- Use a photocell rated for your supply voltage.
Cleaning & Maintenance:
CAUTION: Be sure the fixture temperature is cool enough to touch. Do
not clean or maintain while the fixture is energized.
- Clean the glass lens with a non-abrasive glass cleaning solution.
- Do not open the fixture to clean the LED. Do not touch the LED.
Troubleshooting:
- Check that the line voltage at the fixture is correct. Refer to wiring directions.
- Ensure the fixture is grounded properly.
- Make sure the photocell, if used, is functioning properly.
Frequently Asked Questions (FAQ)
-
Can I use this wall pack for both indoor and outdoor applications?
Yes, this wall pack is suitable for both indoor and outdoor use. -
Is the weatherproof silicone sealant included with the product?
No, the weatherproof silicone sealant needs to be purchased separately. -
What is the recommended maintenance schedule for this product?
It is recommended to clean the glass lens periodically with a non-abrasive glass cleaning solution. Avoid opening the fixture or touching the LED.
WARNING
READ ALL INSTRUCTIONS BEFORE ATTEMPTING INSTALLATION
- To prevent personal injury or product damage only licensed electricians should install.
- To avoid electric shock or component damage disconnect power before attempting installation or servicing.
- This product must be installed in accordance with the national electric code (NEC) and all applicable federal, state and local electric codes and safety standards.
- Disconnect product and allow cooling prior to servicing.
- Any alteration or modification of this product is expressly forbidden as it may cause serious personal injury, death, property damage and/or product malfunction.
- To prevent product malfunction and/or electrical shock this product must be properly grounded.
- This luminaire is designed to operate in ambient temperatures ranging from -40°F to 104°F and to be horizontally mounted with the LEDs facing down.
- Wall mount only.
- THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONST RUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED
- IN 167°F SUPPLY CONDUCTORS
- This product is not available for several special environments, such as places with corrosive gas liquids or high pressure water vapor.
MOUNTING TO A WALL
- Open the Back Box by loosening the Locking Screw.
- Verify and remove only necessary Gasket material where Back Box will mount.
- Knock-out Back Box material for necessary mounting location.
- Mount Back Box to Junction Box securely, using hardware supplied by others.
- Connect electrical connections with fixture wiring.
- Seal Back Box to Housing by pushing on front of Housing while tightening Locking Screw to ensure that screw is fully seated in the Housing Recess. Ensure wiring remains within Back Box and wires do not get pinched using a silicone rubber will ensure a watertight seal.
- If light output angle needs to be adjusted, loosen screw to rotate the fixture to desired light output angle. Tighten screw once desired light output angle is achieved.
- To ensure waterproof seal, apply weatherproof silicone sealant around the edge of the wall mounting box. This is especially important with an uneven wall surface. Silicone all plugs and unused conduit entries.
ON-OFF WIRING
Universal voltage driver permits operation at 60 Hz except fixtures factory ordered with a 120-277VAC (PO)
- Connect the BLACK fixture lead to the(+) LINE supply lead.
- Connect the WHITE fixture lead to the(-) COMMON supply lead.
- Connect the Yellow Green wire from fixture to supply ground.
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to touch. Do not clean or maintain while fixture is energized.
- Clean glass lens with non-abrasive glass cleaning solution.
- Do not open the fixture to clean the LED. Do not touch the LED.
PHOTOCELL INSTALLATION
- Install photocell and wire as per diagram.
- Use photocell rated for your supply voltage.
When installing the 67 /SOW light, please note that the light control and the black and white power cord in the mounting box should be connected with a screw cap as shown above.
TROUBLESHOOTING
- Check that the line voltage at the fixture is correct. Refer to wiring directions.
- Is the fixture grounded properly.
- Be sure the photocell, if used, is functioning properly.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>