xo poppy PY-TLMP Firefly Sound Lamp User Manual

Firefly SOUND LAMP
FCC ID: 2BBPLPYTLMP
PY-TLMP

KEY DIAGRAM

KEY FUNCTION OPERATION

Turn “ON/OFF” switch to the right to enter Bluetooth mode and light mode.
1.Bluetooth Function
The device is switched “ON” with voice prompts. At this time, the audio is in pairing mode.Only in this state can it pair and connect with Bluetooth audio.
2.Mobile Phone Connection
Turn on Bluetooth in your mobile phones settings and connectto “PYeTLMP”
After pairing your mobile phone to the audio is successful, there will be a voice prompt and the connection will be displayed.
3.FM Radio
Press once the M key to switch to FM function. Connect the charging cable to the micro port to act as a radio antenna (the other end does not need to be connected to any equipment).
Press once the pause key to automatically search and saves tations.
Make a saved station selection:

LED FUNCTION

When the device is turned on, the default lowdevel white light effect is achieved.
Tap the center point of the LED Touch Light Sensor to adjust the light from White Light Warm Light/Color Light/ Breathing Light/Rhythm.
1st Gear: Low Light
2nd Gear: Medium Light
3rd Gear: Bright Light
4th Gear: Warm
Sth Gear: is off
Press and Hold: Color Light Mode
Press and Hold for 2 seconds to enter the color light mode.
The order of color light is: Red, Green, Dark Blue, Yellow, Light Blue, Purple, Breathing Light, Rhythm (sound reactive flashes with rhythm when playing music),

FCC STATEMENT

This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation,
Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmtul interference to radio communications. However, there is no guarantee that interference will not occurina particular installation, If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the users encouraged Lo try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna,
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio; TY technician for help.

FCC Radiation Exposure Statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

XOPOPPY © COPYRIGHT ALL RIGHTS RESERVED. XOPOPPY is an innovative company of Truststone Group LLC. No portion of this design may be reproduced without express written permission. Other trademarks and trade names are those of their respective owners. All rights reserved. Distributed by Truststone Group LLC. New York, NY 10018.

CLOCK/ALARM FUNCTION

Clock Setting
Press the time key briefly to enter the clock/minute setting.
Press  to adjust hours/minutes.
Alarm Setting
Press the alarm clock key briefly to enter the clock/minute setting.
Press to adjust hours/minutes,
After setting the time, press the alarm button briefly and press to choose the alarm sound you like.
Finally, press and hold the alarm key to turn on the alarm clock (after setting successfully. the alarm clock will appear on the screen).
Press and hold the light touch sensor part to turn off the alarm when it rings.
Cancel The Alarm
Press and hold the alarm key until the alarm sign on the screen disappears.

TECHINCAL PARAMETERS

To avoid damage caused by excessive voltage, please charge with a plug below 5v. 1200mAh long playing and lighting time. It can be fully charged in 3 hours and continuously working more than 4 hours.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>