IBEAM TE-MIIRW Micro Reverse Backup Camera User Manual TE-MIIRW Product Manual
- February 1, 2024
- iBEAM
Table of Contents
TE-MIIRW Micro Reverse Backup Camera
TE-MIIRW Product Manual
Specifications
Sensor | CMOS |
---|---|
Effective Pixel Video Signal | 480 X 720 NTSC |
Resolution | 500 TV Line |
S/N Ratio | 46dB |
Current Consumption | 35-55 mA |
Power Supply | DC 6V-12V |
Storage Temperature | N/A |
View Angle | N/A |
Water Resistance | N/A |
Minimum Illumination | 0.1 Lux |
Product Usage Instructions
1. Camera Installation
-
Find a suitable location to surface mount install the
camera. -
Ensure that the camera’s view is unobstructed and avoid
drilling into any wires that might damage the vehicle. -
Make all necessary connections before mounting the camera.
-
Verify that the camera is working properly and has a good view
of the area. -
Mount the camera securely using the provided two screws.
2. Wiring Connections
Note: Power can also be obtained in the rear of the vehicle
using the BLUE power wire provided on the extension cable. If this
is done, connect the RED and the BLUE wire closest to the RCA
together. The blue wire is just a pass-through, RED must be
connected to power the camera.
-
Connect the RED wire to the +12 volt reverse wire.
-
Connect the BLACK wire to ground (a metal, non-painted
surface). -
Run the video cable through the vehicle, taking care to avoid
placing it where it can get pinched or damaged. -
Attach the YELLOW video RCA to the camera’s output and to the
reverse camera input of the radio or video display.
3. Loop Cutting Instructions
- Green loop will turn the parking guidelines off.
- White loop will flip the image (top to bottom).
- Blue loop will mirror the image (flip left to right).
FAQ
Q: What should I do if I have difficulties with the
installation?
A: If you are having difficulties with the installation of this
product, please call our Tech Support line at 1-800-253-TECH.
Before calling, please review the instructions again and ensure
that the installation was performed exactly as stated. Have the
vehicle prepared for troubleshooting steps before calling.
REV 1/16/2019
TE-MIIRW Product Manual
1. Find a suitable location to surface mount install the camera. Make sure
the camera’s view is unobstructed and be careful not to drill into any wires
that might damage the vehicle. When all connections have been made and before
mounting the camera, verify the camera is working and has good view of the
area. Then mount the camera down with the supplied two screws.
2. Connect the RED wire to the +12 volt reverse wire
Note: Power can also be obtained in the rear of the vehicle using the BLUE
power wire provided on the extension cable. If this is done, connect the RED
and the BLUE wire closest to the RCA together. The blue wire is just a pass-
through, RED must be connected to power the camera.
3. Connect the BLACK wire to ground (a metal, non-painted surface). 4. Run
video cable though vehicle, up to video display. (Avoid placing video
cable where it can get pinched or damaged). 5. Attach the YELLOW video RCA to
camera’s output and to the reverse camera
input of the radio or video display.
Loop cutting Instructions: Green loop will turn the parking guidelines off
White loop will flip the image (top to bottom) Blue loop will mirror the image
(flip left to right
Sensor
CMOS
Effective Pixel Video Signal
480 X 720 NTSC
Resolution
500 TV Line
S/N Ratio
46dB
Current Consumption 35-55 mA
Power Supply
DC 6V-12V
Operating Temperature -30ºC – 75ºC
Storage Temperature View Angle Water Resistance
-40ºC – 85ºC 175º Diagonal IP68
Minimum Illumination 0.1 Lux
IMPORTANT If you are having difficulties with the installation of
this product, please call out Tech Support line at 1-800-253-TECH. Before
doing so, looks over the instructions a second time, and make sure the
installation was performed exactly as the instructions are stated. Please have
the vehicle apart and ready to
perform troubleshooting steps before calling.
REV 1/16/2019