JVC ARSENAL CS-AW7020 Car Stereo Speaker Instruction Manual

JVC ARSENAL CS-AW7020 Car Stereo Speaker

Thank you!

Thank you for purchasing the ARSENAL Car Stereo Speaker. These Speakers can be mounted in the trunk of your vehicle. For the secure installation and perfect operation of your speakers, please read the following carefully.

Parts

1. Grille

2. Screw x 10

3. Jump
   

4. Fuse (10A) x 2

5. Hexagon socket screw keys

For proper installation and use

1. Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the connection if the power is on may damage the speakers.
2. The amplifier and speakers should be connected between corresponding terminals, i.e. left to left, and right to right, as well as “+” to “+”, and “–” to “–”. Connection with reversed polarity will degrade the quality of stereo reproduction.
3. Do not subject the speakers to excessive input. The power handling capacity of the CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 is 600 watts (R.M.S. MUSIC POWER). Any excessive input may damage the speakers.
4. The CS-AW7020/CS-AW7040/CS-AW7220/CS-AW7240 has an impedance of 2Ω ,4Ω,8Ω. Make sure that the output impedance of the amplifier’s speaker terminal is rated at 2Ω,4Ω,8Ω.
5. When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.
6. Be sure to carefully follow the instructions for:

Cable Connections
Fuse Replacement
Switching the Impedance Selector
Subwoofer Mounting and Smart Trim Ring Installation

Consult Page 19 of this Instruction Manual for details on these procedures.

Dual 4 Ω Application Diagrams

• 1 Mono Amplifier
• 1 Subwoofer
  Jumper set to Series 8Ω(4Ω+4Ω) Load
  

*JUMPER is Removed

• 1 2ch Amplifier

• 1 Subwoofer
  Jumper is Removed 4Ω Load
  

• 1 Mono Amplifier

• 2 Subwoofers
  Jumper set to Series Subwoofers wired in Parallel 4Ω Load
  

• 1 Mono Amplifier

• 3 Subwoofers
  Jumper set to Series Subwoofers wired in Parallel 2.6Ω Load
  

• 1 Mono Amplifier

• 4 Subwoofers
  Jumper set to Series Subwoofers wired in Parallel 2Ω Load
  

• 1 Mono Amplifier

• 1 Subwoofer
  Jumper set to Parallel 8Ω(4Ω+4Ω) Load

*JUMPER is Removed

Bi-Amp Configuration 2 Mono Amplifiers 1 Subwoofer Jumper is Removed 4Ω Load

• 1 Mono Amplifier
• 1 Subwoofer
  Jumper set to Series 4Ω(2Ω+2Ω) Load
  

*JUMPER is Removed

• 1 2ch Amplifier

• 1 Subwoofer
  Jumper is Removed 2Ω Load
  

• 1 Mono Amplifier

• 2 Subwoofers
  Jumper set to Series Subwoofers wired in Parallel 2Ω Load
  

• 1 Mono Amplifier

• 3 Subwoofers
  Jumper set to Series Subwoofers wired in Parallel 1.3Ω Load
  

• 1 Mono Amplifier

• 4 Subwoofers
  Jumper set to Series Subwoofers wired in Parallel 1Ω Load
  

• 1 Mono Amplifier

• 1 Subwoofer
  Jumper set to Parallel 4Ω(2Ω+2Ω) Load
  

*JUMPER is Removed

Bi-Amp Configuration 2 Mono Amplifiers 1 Subwoofer Jumper is Removed 2Ω Load

To install the sealed enclosure

When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also recommended for the enclosure materials.

| CS-AW7020 / CS-AW7040| CS-AW7220 / CS-AW7240
---|---|---
A| 15-13/32 inch (391.7 mm)| 16-13/32 inch (417.1 mm)
B| 15-13/32 inch (391.7 mm)| 16-13/32 inch (417.1 mm)
C| 11-13/32 inch (290.1 mm)| 13-29/32 inch (353.6 mm)
D| 9-4/32 inch (232 mm)| 10-14/32 inch (275.9 mm)
E| 9-23/32 inch (247 mm)| 11-10/32 inch (295 mm)
F| 4/32 inch (3 mm)| 4/32 inch (3 mm)
G| 1.57 ft3 (0.045 m3)| 2.17 ft3 (0.062 m3)

* Screw: Dia. 4mm x 50mm (x 8) (supplied)

To install the ported enclosure

When the speaker cannot be attached in the car, make the sealed enclosure as recommended in the table below—20 mm (3/4 inch) MDF is also recommended for the enclosure materials.

| CS-AW7020 / CS-AW7040| CS-AW7220 / CS-AW7240
---|---|---
A| 15-13/32 inch (391.7 mm)| 15-13/32 inch (391.7 mm)
B| 18-13/32 inch (467.9 mm)| 18-13/32 inch (467.9 mm)
C| 13-13/32 inch (340.9 mm)| 15-13/32 inch (391.7 mm)
D| 9-23/32 inch (247 mm)| 10-14/32 inch (275.9 mm)
E| 9-23/32 inch (247 mm)| 11-10/32 inch (295 mm)
F| 4/32 inch (3 mm)| 4/32 inch (3 mm)
G| 1 inch (25.4 mm)| 1 inch (25.4 mm)
H| 13 inch (330.2 mm)| 14 inch (355.6 mm)
I| 13-19/32 inch (345.4 mm)| 13-6/32 inch (335.3 mm)
J| 1.85 ft3 (0.052 m3)| 2.54 ft3 (0.072 m3)

* Screw: Dia. 4mm x 50mm (x 8) (supplied)

level
Displacement (Liter)| 0.123 ft3|
Hole Cutout Diameter (inch) (mm)| Dia. 9 – 6/32 inch ( 233 mm )|
Mounting Depth (inch) (mm)| 6 – 14/32 inch ( 163.5 mm )|
Re (Ω)| 0.98 Ω| 3.83 Ω| 1.92 Ω| 7.6 Ω| Re: DC voice coil resistance
BL (T.M)| 6.85| 13.75| 8.68| 17.21| BL: Product of Flux density and Effective Voice coil-wire length
Vas (Liter)| 17.08 L| 16.98 L| 18.08 L| 18.28 L| Vas: Volume of air equal to the driver compliance
Vas (CuFt)| 0.6 ft3| 0.599 ft3| 0.64 ft3| 0.65 ft3|
Me (g)| 145.986 g| 147.109 g| 124.084 g| 122.443 g| Me: Effective mass
D (mm)| Dia. 202 mm| D: Effective cone diameter
Fs (Hz)| 39.6 Hz| 39.5 Hz| 41.7 Hz| 41.8 Hz| Fs: Driver free air resonance
Qms| 10.261| 10.282| 9.021| 9.169| Qms: Q of driver at Fs considering only non-electrical resistance
Qes| 0.756| 0.74| 0.83| 0.824| Qes: Q of driver at Fs considering only electrical resistance
Qts| 0.704| 0.691| 0.76| 0.756| Qts: Total Q of driver at Fs
Pe [max.] (W)| 600 W| Pe[max.]: Maximum continuous input power
Xmax.(mm)| 14.95 mm| 14.8 mm| Xmax.: Maximum effective voice coil travel without distortion
Freq. Response (Hz)| 25 ~500 Hz|
Magnet Mass (oz) (g)| 65.4 oz ( 1854.1 g )|
Voice Coil(Aluminum)Dia.(inch) (mm)| Dia. 2 – 5/32 inch 54.5 mm| Dia. 2 – 4/32 inch 53.59 mm|
Hvc (mm)| 39.9 mm| 39.6 mm| Hvc : Voice coil Height
Hag (mm)| 10 mm| Hag: Gap Height
Parameters| CS-AW7220| CS-AW7240| NOTES
---|---|---|---
parallel| series| parallel| series
Nominal Impedance (Ω)| 2Ω + 2Ω| 4Ω + 4Ω|
SPL (dB,1W/1M)| 85.13 dB| 85.2 dB| 85.87 dB| 85.65 dB| SPL : Sound pressure level
Displacement (Liter)| 0.18 ft3|
Hole Cutout Diameter (inch) (mm)| Dia. 10 – 29/32 inch ( 277 mm )|
Mounting Depth (inch) (mm)| 7 – 6/32 inch ( 182.5 mm )|
Re (Ω)| 0.98 Ω| 3.84 Ω| 1.94 Ω| 7.61 Ω| Re: DC voice coil resistance
BL (T.M)| 6.84| 13.72| 9.56| 19.14| BL: Product of Flux density and Effective Voice coil-wire length
Vas (Liter)| 38.7 L| 38.76 L| 35.23 L| 35.05 L| Vas: Volume of air equal to the driver compliance
Vas (CuFt)| 1.37 ft3| 1.37 ft3| 1.24 ft3| 1.24 ft3|
Me (g)| 171.854 g| 172.934 g| 157.028 g| 157.336 g| Me: Effective mass
D (cm)| Dia. 246 mm| D: Effective cone diameter
Fs (Hz)| 34.6 Hz| 34.5 Hz| 37.9 Hz| 38 Hz| Fs: Driver free air resonance
Qms| 10.277| 10.089| 8.931| 9.014| Qms: Q of driver at Fs considering only non-electrical resistance
Qes| 0.786| 0.765| 0.794| 0.781| Qes: Q of driver at Fs considering only electrical resistance
Qts| 0.73| 0.711| 0.73| 0.719| Qts : Total Q of driver at Fs
Pe [max.] (W)| 600 W| Pe[max.] : Maximum continuous input power
Xmax.(mm)| 14.95 mm| 14.8 mm| Xmax.: Maximum effective voice coil travel without distortion
Freq. Response (Hz)| 23 ~500 Hz|
Magnet Mass (oz) (g)| 86.2 oz ( 2443.7 g )|
Voice Coil(Aluminum)Dia.(inch) (mm)| Dia. 2 – 5/32 inch ( 54.5 mm )| Dia. 2 – 4/32 inch ( 53.59 mm )|
Hvc (mm)| 39.9 mm| 39.6 mm| Hvc: Voice coil Height
Hag (mm)| 10 mm| Hag: Gap Height

Dimension

CS-AW7020
CS-AW7040

CS-AW7220
CS-AW7240

Product Name

T3 Chassis (Thermal Transfer Technology)

Instructions For Use

TO OUR VALUED CUSTOMER

THANK YOU FOR PURCHASING THIS JVC PRODUCT.
WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.

NEED HELP ON HOW TO HOOK UP?
NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?

IS HERE TO HELP!

TOLL FREE: 1(800)252-5722 http://www.jvc.com

Remember to retain your Bill of Sale for Warranty Service.

Do not attempt to service the product yourself

Caution
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.

References

• JVC USA - Products
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>