Lenco L-30 Turntable with USB PC Encoding Wood User Manual
- June 16, 2024
- Lenco
Table of Contents
Lenco L-30 Turntable with USB PC Encoding Wood
Product Information
Specifications
- Model: L-30/L-101
- Cartridge: MMC
- Encoding: PC
- Base Material: Wood
- Power Adaptor: Included
- Speeds: 33 RPM, 45 RPM
- Output Jacks: RCA, USB
Turntable Parts
- Phono Stylus Cartridge
- Turntable Platter
- Lift Lever
- Turntable Arm Lock
- Auto Stop Control Switch
- Speed Selection Switch
- Turntable Shaft
- Turntable Arm
- RCA Output Jack
- USB Jack
- Power Adaptor Jack
- Power ON/OFF Button
Product Usage Instructions
Precautions Before Use
-
Do not use this device near water.
-
Clean only with a slightly damp cloth.
-
Do not cover or block any ventilation openings. Leave at least 5 cm (2 inches) of free space around the device.
-
Install the turntable according to the supplied user manual.
-
Avoid stepping on or pinching the power adaptor and its cable to prevent interference and data failure.
-
Avoid exposing the device to dripping or splashing liquids.
Keep objects filled with liquids away from the device. -
To completely disconnect the power input, unplug the mains plug of the apparatus.
-
Ensure easy access to the mains plug during intended use.
-
Avoid exposing the battery to excessive heat.
-
Provide a minimum distance of 10cm around the apparatus for sufficient ventilation.
-
Do not impede ventilation by covering the ventilation openings with items such as newspapers or curtains.
-
Avoid placing naked flame sources, like lighted candles, on the apparatus.
-
Pay attention to the environmental aspects of battery disposal.
-
Use the apparatus in moderate climates and avoid extremely cold or warm environments.
-
Refer to the rating label on the bottom panel of the apparatus for additional information.
-
This device is not intended for use by people (including children) with physical, sensory, or mental disabilities unless supervised or instructed by a responsible person.
Listening to a Record
- Connect the RCA Output Jack to an external speaker system using an RCA cable (not included).
- Raise the dust cover.
- Press the Power ON/OFF Button.
- Place a record on the turntable platter.
- Set the player speed to match the record speed.
Note: When playing a single (a 45 rpm record) and/or records with large centre holes, use the 45 rpm adapter.
Remark: The AUTO STOP function applies to most 33 RPM vinyl records. However, for very few vinyl records, it may stop when it does not come to the end or not stop when it comes to the end when AUTO STOP is ON.
FAQ
- Q: Can I use this turntable near water?
- A: No, it is not recommended to use the turntable near water.
- Q: How should I clean the turntable?
- A: Clean the turntable using a slightly damp cloth.
- Q: Can I cover or block the ventilation openings?
- A: No, it is important not to cover or block the ventilation openings to ensure proper airflow.
- Q: How do I connect the turntable to an external speaker system?
- A: Connect the RCA Output Jack of the turntable to the external speaker system using an RCA cable (not included).
- Q: What should I do if the turntable does not stop at the end of a vinyl record?
- A: If the AUTO STOP function does not work correctly for a particular vinyl record, you may need to manually stop the turntable.
CAUTION
Usage of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This unit should not be adjusted or repaired by anyone except qualified
service personnel.
PRECAUTIONS BEFORE USE
KEEP THESE INSTRUCTIONS IN MIND
- Do not use this device near water.
- Clean only with a slightly damp cloth.
- Do not cover or block any ventilation openings. When placing the device on a shelf, leave 5 cm (2”) free space around the whole device.
- Install by the supplied user manual.
- Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s exit point. Do not place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s reach! When playing with the power cable, they can seriously injure themselves.
- Unplug this device during lightning storms or when unused for a long period.
- Keep the device away from heat sources such as radiators, heaters, stoves, candles and other heat-generating products.
- Avoid using the device near strong magnetic fields.
- Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart the device following the instruction manual. During file transmission, please handle it with care and operate in a static-free environment.
- Warning! Never insert an object into the product through the vents or openings. High voltage flows through the product and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do not spill water or liquid on the product.
- Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.
- Do not use this device when condensation may occur.
- Although this device is manufactured with the utmost care and checked several times before leaving the factory, it is still possible that problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you should disconnect the plug from the main power socket immediately.
- This device must be well-ventilated at all times!
- This device must operate on a power source as specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.
- The socket outlet must be installed near the equipment and must be easily accessible.
- Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
- Devices with class 1 construction should be connected to a main socket outlet with a protective earthed connection.
- Devices with class 2 construction do not require an earthed connection.
- Keep away from rodents. Rodents enjoy biting on power cords.
- Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause a short circuit.
- Avoid placing the device on any surfaces that may be subject to vibrations or shocks.
- To protect the device during a thunderstorm, unplug the AC power adaptor.
- When the device is not in use for long periods, unplug the AC power adaptor for safety reasons.
- To clean the device, use a soft dry cloth. Do not use solvents or petrol-based fluids. To remove severe stains, you may use a damp cloth with dilute detergent.
- The supplier is not responsible for damage or lost data caused by malfunction, misuse, modification of the device or battery replacement.
- Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted or lost.
- The usb memory stick should be plugged into the unit directly. Don’t use a usb extension cable because it can cause interference in failing data.
- The apparatus shall not be exposed to dripping or splashing and make sure that no objects filled with liquids, such as vases, are placed on or near the apparatus.
- To completely disconnect the power input, the mains plug of the apparatus shall be disconnected from the mains, as the disconnect device is the mains plug of the apparatus.
- The mains plug of the apparatus should not be obstructed or should be easily accessed during intended use.
- Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
- A minimum distance of 10cm around the apparatus is needed for sufficient ventilation.
- The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains etc.
- No naked flame sources such as lighted candles should be placed on the apparatus.
- Attention should be drawn to the environmental aspects of battery disposal.
- The apparatus can only be used in moderate extremely cold or climates warm environments should be avoided.
- The rating label has been marked on the bottom panel of the apparatus.
- This device is not intended for use by people (including children) with physical, sensory or mental disabilities, or a lack of experience and knowledge unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for their safety.
- This product is intended for household use only and not for commercial or industrial use.
- Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.
- Never remove the casing of this apparatus.
- Never place this apparatus on other electrical equipment.
- Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or vibration.
- Do not clean this product with water or other liquids.
- Do not block or cover the slots and holes in the product.
- Do not push foreign objects into the slots or holes in the product.
- Do not allow children access to plastic bags.
- Please check that the voltage on the type plate of your appliance corresponds with your house’s electricity supply (the type plate is located on the back of the unit).
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or the plug, when the liquid has been spilled or objects have fallen into the apparatus when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or electric shock.
Warning: prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.
INSTALLATION
- Unpack all parts and remove protective material.
- Do not connect the unit to the mains before checking the mains voltage and before all other connections have been made.
- Do not cover any vents and make sure that there is a space of several centimetres around the unit for ventilation.
BEFORE USE
- Choose a safe location and avoid placing the unit in direct sunlight or near any heat source.
- Avoid environments subject to vibration, excessive dust, cold or moisture.
- Due to the risk of electrical shock, do not open the cabinet. Should a foreign object accidentally find its way into the interior of the unit, contact your local dealer.
- Do not attempt to clean the unit with chemical solvents as this might damage the finishing. A clean, dry cloth is recommended for cleaning.
- Keep this manual for future reference.
TURNTABLE PARTS
- Phono Stylus Cartridge
- Turntable Platter
- Lift Lever
- Turntable Arm Lock
- Auto Stop Control Switch
- Speed Selection Switch
- Turntable Shaft
- Turntable Arm
- RCA Output Jack
- USB Jack
- Power Adaptor Jack
- Power ON/OFF Button
LISTENING TO A RECORD
- Connect the RCA Output Jack to the external speaker system with the RCA cable (not included).
- Raise the dust cover
- Press the Power ON/OFF Button.
- Place a record on the turntable platter and set the player’s speed to match the record speed.
NOTE: when playing a single (a 45 rpm record) and/or records with large centre holes, use the 45 rpm adapter.
Remove the needle cartridge protective cover and unlock the tone arm lock from
the tonearm rest. Push the lift lever backward, the tone arm will gently rise.
Gently move the tone arm to the desired position over the record and the
turntable platter will begin to rotate when the arm is moved towards it if
Auto Stop Control Switch is ON. Release the tone arm onto the turntable by
pushing the lift lever forward and the vinyl record will begin to play.
If the Auto Stop Control Switch is turned ON, the record will stop
automatically when finished. If the Auto Stop Control Switch is turned OFF,
the record will NOT stop automatically when finished; you must push the lift
lever backward to raise the tone arm and place it back in the rest and then
turn off the power to stop the turntable from spinning.
Remark: The AUTO STOP function applies to most 33RPM vinyl records.
However, for very few vinyl records, it will stop when it does not come to the
end, or it will not stop when it comes to the end when AUTO STOP is ON.
RECORD YOUR VINYL ON YOUR WINDOWS PC
Setup
Connect the USB cable with your turntable and your computer. No extra driver
is required.
Audacity Installation
Insert the installation CD. Your computer will auto-run the program. Follow
the instructions to complete the installation.
If your computer does not auto-run, click on the “Start” menu, select “Run”
choose the CD located on your computer and run “Setup.exe”
Run Audacity Program
Double-click on the Audacity program and the Audacity interface window will be
displayed on your computer screen.
Playback Control Toolbar
Audacity will display a control toolbar for you to edit and manage your
recordings.
Playing Your Record
Play the record you want to record by following the procedure described in the
section “LISTENING TO A RECORD”
Adjusting Input and Output
Adjust the output and input volume.
EN | EN |
---|---|
Output volume | Output volume |
Input volume | Input volume |
Recording
Select the RECORD button to start recording while your record is playing.
You will need to position the needle on the record for a few seconds before
the track starts so that you select the RECORD button at the beginning of your
track.
Start playback on the USB turntable. You will see the waveform of the audio on
the screen as it is recorded. You will hear the audio coming from the output
of your computer’s sound card.
No Audio? – go back to the preference menu and make sure you have “Software
Playthrough” selected and the speaker volume up on your computer.
Press Stop
SAVE YOUR FILE NOW by clicking on “File” followed by “Save Project” Select the
destination and file name for the project and click “Save” Once finished
recording, your screen should display your recording as below.
Editing your Recording
Audio Levels
Select your entire recording by selecting “Edit,” then “Select…” then click
“All.”
- Select the “Effect” menu and choose the desired effect. There are various types of effects which are described further on Audacity’s website.
- Selecting “Normalize” should be used to have Audacity auto-correct volume on the recording.
Noise Reduction
Drag your cursor over a portion of the audio track that contains unwanted
noise. We recommend using the beginning or end of a track where there is no
music and only noise.
- Select “Effect” and then “Noise Removal” from the drop-down menu to bring up the “Noise Removal Window”
- Click “Get Noise Profile” and the window will close automatically.
- Select the entire track of audio you wish to remove noise from.
- Adjust the amount of audio that you would like to filter by moving the slider in the “Noise Removal” window. We recommend using the minimum noise removal for optimum sound.
Note: you can preview the audio before removing the noise by clicking on ‘Preview’.
- Click on ‘Remove Noise’.
The Editing Toolbar
The Tools Toolbar
Before editing, you must make a selection of the recording you would like to cut or copy. This will trim any music from the previous track, or any silence on the record between tracks.
-
To select the part you wish to cut, copy or paste, use the selection tool. If it is not activated, do so by clicking on it in the toolbar.
-
Press and hold the left mouse button while you drag the mouse to a marked area.
-
This area is darker than the surrounding area of the clip. Note, that even though you can mark an area larger than or extending beyond the actual audio clip in the track, the operations will only work on the actual clip. Playback however will work outside the clip.
-
Press the space bar to listen to the audio in the marked area.
-
To extend or contract your selection, hold down the SHIFT button and click on the area you wish your selection to extend or contract to.
-
If you click at a spot that is on the right-hand side from the middle of the current selection, you will set the right-hand boundary of your new selection.
-
Now you must cut your selection. Select “Cut” from the “Edit” menu.
- Create a new file and paste your cut into the new file.
Exporting to MP3
To export your recording to mp3 format, select “Export As” from the “File”
menu. You will need to choose which format to export to. Choose “.mp3” as your
file extension. When exporting, do not choose your Desktop as the destination
folder. You can only choose “My Documents” folder. After export, you can move
the files as desired.
For additional software information, please refer to http://audacity.sourceforge.net for detailed operating instructions.
TIPS FOR BETTER TURNTABLE PERFORMANCE
- When opening or closing the turntable cover, handle it gently, gripping it either at the centre or at each side.
- Do not touch the needle tip with your fingers; avoid bumping the needle against the turntable platter or record edge.
- Gently wipe the dust cover and turntable housing with a soft cloth. Use only a small amount of mild detergent to clean the turntable and dust cover.
- Never apply harsh chemicals or solvents to any part of the turntable system.
Power supply adaptor
- Manufacturer: SHENZHEN SHI GUANGKAIYUAN TECHNOLOGY., LTD.
- Model number: GKYPS0100120EU1
- Use only the original AC adaptor
- Use only the power supply listed in the user instructions
Lenco|
---|---
Turntable| L-30 / L-101
Type| Belt drive auto-stop
Drive Motor| DC motor
Speed| 33 1/3rpm,45rpm
Wow and flutter| ﹤0.35%
Turntable platter| 300mm
Cartridge|
Type| Chuden MG-2590 MM
Stylus| 0.6mil
Optimum tracking force| 2.5-3.5gr
Output| 2.4mv±3db
Frequency response| -1.5±6db(10KHz)
Crosstalk| 16db(1KHz)
Signal-to-noise ratio(S/N)| 40db
General|
ADAPTOR| input AC100-240V~50/60Hz0.5A
output DC12V1000mA
PRODUCT| DC12V200mA
Audio output(Line Out)| 400-600mv
Power consumption| 2.4W
Dimension| 410330116MM
Net weight| approx 3.1KGS
Guarantee
Lenco offers service and warranty under European law, which means that in case
of repairs (both during and after the warranty period) you should contact your
local dealer.
Important note: It is not possible to send products that need repairs to
Lenco directly.
Important note: If this unit is opened or accessed by a non-official
service centre in any way, the warranty expires.
This device is not suitable for professional use. In case of professional use,
all warranty obligations of the manufacturer will be voided.
Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore
some of the instructions, specifications and pictures in this documentation
may differ slightly from your particular situation. All items described in
this guide are for illustration purposes only and may not apply to particular
situations. No legal right or entitlements may be obtained from the
description made in this manual.
Disposal of the Old Device
This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose of them in accordance to any applicable local laws of the requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in the treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).
CE Marking
Products with the CE marking comply with the EMC Directive (2014/30/EU) and the Low Voltage Directive (2014/35/EU) issued by the Commission of the European Community.
Hereby, Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands,
declares that this product complies with the essential requirements.
The declaration of conformity may be consulted via
techdoc@lenco.com.
Service
For more information and helpdesk support, please visit
www.lenco.com.
Lenco Benelux BV, Thermiekstraat 1a, 6361 HB Nuth, The Netherlands.
References
- Audacity download | SourceForge.net
- Audacity download | SourceForge.net
- Audacity download | SourceForge.net
- Lenco.com | Officiële Lenco Webshop
- Lenco.com | Officiële Lenco Webshop
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>