LG FHT1006SNW Front Load Washing Machine Owner’s Manual

LG FHT1006SNW Front Load Washing Machine

Product Features

Protection against creases
With the alternate rotation of the drum, creasing in the laundry is minimized.

Built-in heater
The internal heater automatically heats the water to the best temperature on selected cycles. More economical by Intelligent Wash System Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.

Child Lock
The Child lock prevents children from changing the settings if they Press any button during the operation.

Low noise speed control system
By sensing the amount of load and balance, it evenly distributes the load to minimize the spinning noise level.

Auto Restart
Auto Restart allows the program to restart all by itself in case of power failure. It does from the stage where it stopped. The washer can perform various drum actions or a combination of different actions depending on the wash program selected.
Combined with a controlled spin speed and the ability of the drum to

MOTION
rotate both left and right, the wash performance of the machine is greatly improved, giving you perfect results every time.

Direct Drive System
The advanced Brushless DC motor directly drives the drum without a belt and pulley. This Manual may contain images or content different from the model you purchased. This Manual is subject to revision by the manufacturer.

safety Information

READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE

WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

WARNING
To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

• Before installation, check exterior damages. If it has, do not install it.

• Do not install or store the washer where it will be exposed to the weather (Rain / Water Splash).

• If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.

• Do not tamper with controls.

• It may lead to electric shock, fire, break down or deformation.

• Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.

• Operating the machine with improperly replaced parts may be a cause for fire or electric shock.

• Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc.

• Operating with such materials around the machine may trigger an explosion or fire.

• close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.

• There is a potential danger that children might drown in the tub.

•  Keep small animals away from the appliance.

• Do not leave the washer door open. An open door could entice children to hang on the door or crawl inside the washer.

• Never reach into washer while it is moving. Wait until the drum has completely stopped.

• Even slow rotation can cause injury.

• The laundry process can reduce the flame retardant of fabrics.To avold such a result, carefully follow the garment manufacturer’s wash and care instructions.

• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.).

• It may ignite or explode. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oiled clothes.

• Do not slam the washer door closed or try to force the door open when locked.

• This could result in damage to the washer.

• When the machine runs high temperature, the front door may be very hot. Don’t touch it.

• To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer from the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

• When unplugging power cord, do not pull out by grasping the cord.

• Otherwise, the power cord may be damaged.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

• Operating with a damaged plug may cause electric shock.

• Before discarding an old machine unplug it. Render the plug useless. Cut off the cable directly behind the appliance to prevent misuse.

• when a product was under water, Please call service center. The risk of electric shock and fire.

• When washer door is opened, do not push down the door excessively.

• This could topple over the washer.
  SAVE THESE INSTRUCTIONS GROUNDING INSTRUCTIONS

• This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of elactric shock by providing a path of least resistance for electric current. This appliance is equipped with cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is property installed and grounded by all local codes & ordinance.

• Do not use an adapter or otherwise defect the grounding plug. ” you ount have te wover cune, consult an excuicion.

• WARNING
  Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with a qualitied electrician or serviceman if you are indoubt the plug provided with the appliance-if it does not fit the outiet, have a proper outiet installed by a qualified electrician as to whether the appliance is property grounded.

• Do not modify the piug provided with the appliance if it does not fit the cutlet, have a proper cutiet installed by a qualified electrician.

specifications

1.  Transit bolts
2. Power plug
3. Drawer
4. Control panel
5. Drum
6. Door*
7. Drain hose
8. drain plug
9. Drain pump filter
10. Cap Cover
11. Adjustable Leg

Name
Front-loading washing machine

Power supply
220V~,50Hz

Size
600mm(W) x 450mm(D) x 850mm(H)
Weight/Max. Watt: 62kg / 1700W

Wash capacity
7.0kg: [FHT1207SNW/L/S] 6.5kg: [FHT1265SNW/L/S, FHT1065SNW/L/S
6.0kg: [FHT1006SNW/L/S, FHT1006HNW/L/S]

Spin speed
No/400/800/1000/1100/1200: [FHT1207SNW/L/S, FHT1265SNW/L/S] No/400/600/800/900/1000: [FHT1065SNW/L/S, FHT1006SNW/L/S, FHT1006HNW/L/S]

Permissible water pressure :100-1000kPa (1.0-10kgf/cm’ )
The appearance and specifications may be varied without notice to raise the product quality.

Accessories

Parts can be different according to different models.

Installation

Install or store where it will not be exposed to temperatures below freezing or exposed to the weather. Properly ground washer to conform with all governing codes and ordinances. The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. In countries where there are areas that may be subjected to infestation by cockroaches or other vermin, pay particular attention in keeping the appliance and its surroundings in clean condition at all times.  Any damage which may be caused by cockroaches or other vermin will not be covered by the appliance guarantee.

Unpacking
Cut the straps and open the upper flaps of the Packing box & take out the Anti Rat Cover. While taking out the Machine from packing, please take due care in removing the packing support given at centre of the base packing.

Anti-cover installation

Accessories for fixing Anti Rat Cover.

1. Take out the poly bag (containing Screws/Washers).
2. Tilt the machine sideways.
3. Bend & insert the flaps of the rat Cover into the bottom side of the machine.
4. Assemble the Anti Rat Cover on the bottom side of the machine by using Screws & Washers.
5. Transit bolts
6. The appliance is fitted with transit bolts to prevent internal damage during transport.
7. Packing and all transit bolts must be removed before using the Machine.

**Removing transit bolts

**

1. To prevent internal damage during transport, the special 4 bolts are locked. Before operating the washer, remove the bolts along with the rubber bungs.
2. If they are not removed, it may cause heavy vibration, noise and malfunction.
3. Unscrew the 4 bolts with the spanner supplied.
4. Take out the 4 bolts along with the rubber bungs by slightly twisting the bung. Keep the 4 bolts and the spanner for future use.
5. Whenever the appliance is transported, the transit bolts must be refitted.
6. Close the holes with the caps supplied.

**Installation place requirement

**

• Drain Huse
• Washer
• Laundry
• Tub

Level floor
The allowable slope under the entire washer is 1°

Power outlet
Must be within 1.5 meters of either side of the location of washer. Do not overload the outlet with more than one appliance.

Additional Clearance
For wall, door and floor modeling is required. (10cm : rear /2cm:right & left side) Do not place or store laundry products on top of washer at any times. They can damage the finish or controls.

Connecting water supply hose

• Water supply pressure must be between 100kPa and 1000kPa (1.0~10kgf/cm?)
• Don’t strip or crossthread when connecting Inlet hose to the valve.
• If the water supply pressure is more than 1000kPa, a decompression device should be installed.
• Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks.
• Make sure the connection to taps is tight enough.
• Periodically check the condition of the hose and replace the hose if necessary.
• Make sure that there is no kink on the hose and that it is not crushed.

Normal Tap without thread & screw type inlet hose

1. Unscrew the fixing screw to Push the connector up till.

2. Push the water supply hose and attach the tap. rubber packing is in tight contact vertically upwards so that the with the tap. Then tighten the 4 rubber packing within the screws.

3. Upper Connector the tap and then tighten it by Rubber Pukhar knocking screwing it to the right.

4. Untighten the upper connector 2. Push the upper connector up till 3.

5. Connect the water supply hose screw.

6. Rubber contact with the tap. Then to the middle connector, tighten the 4 screws… pushing the plate down.

7. Turn the middle connector notto have water leaked.

8. Make sure that the rubber seal  is inside the hose connector.

9. To separate the water supply hose from the middle connector shut off the tap. Then pull the inlet hose down, pushing the plate down.

10. Your machine comes with only cold water connection.

11. Make sure that there are no kinks in the hose and that it is not crushed.

Tap with thread & screw type inlet hose

• Two rubber seals are provided with inlet hose connectors.
  • These are used to prevent water leakage.
  • Make sure the connection to tap is sufficiently tight.
• Check rubber seals in inlet hose connectors.
• Screw the hose connector onto water supply tap.

Positioning

• Install the washer on a flat hard floor. Make sure that air circulation around the washer is not impeded by carpets,rug etc.
• Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the washer.
• If it is impossible to avoid positioning the washer next to a gas cooker or coal-burning stove, an insulation(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliances.
• The washer must not be installed in rooms where the temperature can drop below 0°C
• Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown.
• With the washer installed adjust all four adjustable legs using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top.

WARNING
It is advisable to avoid, the usage of trolley & the movement of Washing Machine after installation, As it may disturb the levelling of washer, which can create excessive noise & vibration.

1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or equally qualified person in order to avoid a hazard
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket by current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
6. Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunction. Contact your local service center.
7. Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
8. If the appliance is delivered in the winter months and temperatures are below freezing: Place the washing machine at room temperature for a few hours before putting it into operation.

CAUTION
The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play with appliances.

CAUTION
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit that powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service Centre. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

• Washing Machine is to be connected to the water mains using new hose-sets and old hose sets should not be used.
• Connecting water supply hose*
• Water supply pressure must be between 100kPa and 1000kPa (1.0~10kgf/cm3)
• Don’t strip or crossthread when connecting Inlet hose to the valve.
• If the water supply pressure is more than 1000kPa, a decompression device should be installed.
• Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks.
• Make sure the connection to taps is tight enough.
• Periodically check the condition of the hose and replace the hose if necessary.
• Make sure that there is no kink on the hose and that it is not crushed.

NOTE
After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor. Part can be different according to different models.

Normal Tap without thread & screw type inlet hose

1. Unscrew the fixing screw to
2. Push the connector up till the attach the tap. rubber packing is in tight contact with the tap. Then tighten the 4 screws.
3. Upper
4. Connector
5. Rubber

Turn the middle connector not to have water leaked. Make sure that the rubber seal ic incide the hace ennnector To separate the water supply hose from the middle connector shut off the tap. Then pull the inlet hose down, pushing the plate down.

Tap with thread & screw type inlet hose

1. Two rubber seals are provided
2. check rubber seals in inlet hose 3. Screw the hose connector ontowith inlet hose connectors. connectors.  water supply tap.
3. These are used to prevent water leakage.
4. Make sure the connection to tap is sufficiently tight.

INSTALLATION

This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable and destroy the plug. Break the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam,PE Bags) can be dangerous for children. There is a risk of suffocation ! Keep all packaging well away from children.

Installation of drain hose

• The drain hose should not be placed higher than 100 cm above the floor.
• Proper securing of the drain hose will protect the floor from getting wet due to water leakage.
• When the drain hose is too long, do not force back into the washer. This will cause abnormal noise/leakage.

Level adjustment adjustable leg
Adjustable leg Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.

NOTE
Timber or suspended type flooring may contribute to excessive vibration and unbalance errors. If the floor is uneven, adjust the adjustable leg as required. (do not insert pieces of wood etc. under the legs) Make sure that all four legs are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level) After the washer is levelled, tighten all lock nuts up towards the base of the washer.

NOTE
In the case the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk that it might fall off.

Diagonal Check
When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. (Please, check both of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the legs again.

Concrete floors

• The installation surface must be clean, dry and level.
• Install washer on a flat hard floor.

Tile floors (Slippery floors)

Position each leg on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70×70 mm sections and stick the pieces on to the dry tile where machine is to be placed.)
Tread Mate is a self adhesive material used on ladders & steps that prevents slipping.

Wooden floors (Suspended floors)

• Wooden floors are particularly susceptible to vibration.
• To prevent vibration we recommend you place rubber cups under each leg, at least 15mm thick under the washer, secured to at least 2 floor beams with screws.
• If possible, install the washer in one of the corners of the room, where the f loor is more stable.
• Insert the rubber cups to reduce vibration.
• You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept.

Important!

• Proper placement and levelling of the washer ensure long, regular and reliable operation.
• The washer must be absolutely horizontal and stand firmly in position.
• It must not “Seesaw” across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not let the legs of the washer get wet. If legs of the washer get wet, slipping may occur.

Care before washing

• Before the first washing
• Select a cycle (Cotton 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing.
• Caring before washing

Care Labels
Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.

Sorting
To get the best results, Sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discoloration of white etc. If possible, do not wash heavily soiled items with lightly soiled one.

Soil (Heavy, Normal, Light)
Color (White, Lights, Darks) Lint (Lint producers, Collectors) Separate clothes according to amount of soil. Separate white fabrics from colored fabrics. Wash lint producers and lint collectors separately.

Caring before loading
Combine large and small items in a load. Load large items first. Large items should not be more than half the total wash load. Do not wash single items. This may cause an out-of-balance load. Add one or two similar items.

• Check all pockets to make sure that they are empty. Items such as nails, hair clip, matches, pens, coins and keys can damage both your washer and your clothes.
• Pre treat dirt and stains by brushing a little detergent dissolved in water onto stains like collars and cuffs to help shift dirt.
• Close zippers, hooks and strings to make sure that these items don’t snag on other clothes.
• Check the folds of the flexible gasket (gray) and remove any small articles, if any.
• Check inside of the drum and remove any left items in it for next wash cycle.
• Remove any clothing or items on the flexible gasket to prevent clothing and the gasket damages.

Adding detergent
Adding detergent and fabric softener

The Dispenser Drawer

• Main wash only → L/
• Pre Wash + Main Wash → L W

WARNING
Keep all washing detergents away from children as there is danger of poisioning. Too much detergent, bleach or softener may cause an overflow. Be sure to use the appropriate amount of detergent.

**Adding Fabric Softener

**

• Do not exceed the maximum fill line.

• Close the dispenser drawer slowly.

• Overfilling can cause early dispensing of the fabric softener which could stain clothes.

• Do not leave the fabric softener in thedetergent drawer for more than 2 days. (Fabric softener could harden)

• Softener will be automatically added during the last rinse cycle.

• Do not open the drawer when water is supplied.

• Solvents(benzene etc) are not allowable.
  NOTE

• Do not pour fabric softener directly on the cloths

Detergent dosage

• The detergent should be used according to the instruction of the detergent manufacturer.
• If too much detergent is used, too many suds can occur and this will decrease the washing result or cause heavy load to the motor.
• It is recommended that you use powdered detergent for best results.
• If you wish to use liquid detergent follow guidelines provided by the detergent manufacturer.
• You can pour liquid detergent directly in to the main detergent drawer if you are starting the cycle immediately.
• Please do not use liquid detergent if you are using ‘Delay End’ as the liquid may harden, or if you have selected ‘Pre-Wash’.
• If suds occur too much, please reduce the detergent amount.
• Detergent usage may need to be adjusted for water temperature, water hardness, size and soil level of the load. For best results, avoid over sudsing.

WARNING
Do not let the detergent harden. Doing so may lead to blockages,poor rinse performance or bad odor. Full load: according to manufacturer’s recommendation.

NOTE

• Part load: 3/4 of the normal amount.
• Minimum load : 1/2 of full load.
• Detergent is flushed from the dispenser at the beginning of the cycle.

Adding water softener
A water softener, such as Anti limescale (e.g. Calgon) can be used to cut down on the use of detergent in extremely hard water areas. Dispense according to the amount specified on the packaging. First add detergent and then the water softener. Use the quantity of detergent as for soft water.

**Using the Tablets

**

1. Open the door and put tablets into the drum.
2. Load the laundry into the drum and close the door.

Recommended courses according to the laundry type

Water Temperature: Select the water temperature to the wash cycles. Always follow garment manufacturer’s care label or instructions when laundering.

Notes: Neutral detergent is recommended.

Extra Options

Program| Time Save| Intensive| Rinse- +-| Delay

End

| Crease

Car e

| Pre VVash
---|---|---|---|---|---|---
Cotton| .| .| .| .| .| .
Cotton+ O| .| .| .| .| .| .
Easy Car e| .| .| .| .| .| .
Mix| .| .| .| .| .| .
Allergy Care| .| .| .| .| .| .
Baby Steam

Care

| .| .| .| .| .| .
SllentVVash| .| .| .| .| .| .
Duvet| .| .| .| .| .| .
Sports VVear| .| .| .| .| | .
D a rk VVa s h| .| .| .| | .| .
Quick 30| .| .| .| .| .| .
G e ntle Care| .| .| .| .| .| .

Extra Options selection can vary depending on different models.

How to use a washer
Part can be different according to different models.

Control Panel

• Power Button Press the Power button to turn the washing machine on.
• Start/Pause Button This Start/Pause button is used to start the wash cycle or pause the wash cycle.
• If a temporary stop of the wash cycle is needed, press the Start/Pause button.
• Display The display shows the settings, estimated time remaining, options, and status messages. When the product is turned on, the default settings in the display will illuminate.
• The display shows the estimated time remaining. While the size of the load is being calculated automatically, blinking or ‘Detecting’ appears.
• The RPM may differ depending on the models. Program Knob Programs are available according to the laundry type.
• The lamp will light up to indicate the selected program.
• Options This allows you to select an additional program and will light when selected. Use these buttons to select the desired program options for the selected cycle.

Beep On / Off

1. Press the Power button.
2. Press the Start/Pause button.
3. Press and hold the Temp. and Delay End button simultaneously for 3 seconds to set the Beep on/off function.
   NOTE
   Once the Beep on/off function is set, the setting is memorized even after the power is turned off. If you want to turn the Beeper off, simply repeat this process.

How to use a washer

Parts can be different according to different models.

1. Button: Power
2. Button: Start / Pause
3. Display
4. Dial: Program
5. Options

Power
Press the Power button to turn the washing machine ON/OFF. To cancel the Time Delay function, the power button should be pressed.

Initial Program

• When the Power button is pressed, the washer is ready for the Cotton program and the other initial conditions are as follows.
• So, if you want to advance into the washing cycle without changing the program, just press the Start/Pause button and then the washer will proceed.
• Initial program [FHT1207SNW/L/S, FHT1265SNW/L/S] Cotton Program/Main Wash/ Normal Rinse/1200rpm/40°C [FHT1065SNW/L/S, FHT10065NW/L/S, FHT1006HNW/L/S]
• Cotton Program/Main Wash/ Normal Rinse/ 1000pm/40°C 14 programs are available according to the laundry type.
• The lamp will light up to indicate the selected program.
• When the Start/Pause button is pressed, the Cotton program is automatically selected.
• By turning the Program dial, the program is selected in order of “Cotton – Cotton+ – Mix – Easy Care –
• Duvet-Allergy Care – Baby Steam Care –
• Download Cycle –
• Quick 30 – Silent Wash – Stain Care -Dark Wash – Gentle Care – Sports Wear”
• Regarding to the laundry type for each program Please refer to the page 14.

Program

Start/Pause

Start
This Start/Pause button is used to start wash cycle or pause the wash cycle.

Pause
If a temporary stop of the wash cycle is needed, press the Start/Pause button. When in Pause, the power is turned off automatically after 4 minutes approx.

DOOR LOCK

• Lights whenever the door of the washer is locked.
• The door can be unlocked by pressing the Start/Pause button to stop the washer.
• The door can be opened after a short delay.

Detecting (a))
While the is shown in the display the machine rotates slowly and detects how much laundry is loaded in the drum. It will take a few seconds.

Option
By Pressing the Option Button, all Option functions may be selected.

1. Intensive ( 14)
   • If the laundry is heavily soiled “Intensive” option is effective.
   • By selecting the intensive option, the wash time may be extended, depending on the program selected.
2. Time Save (-2)
   • This option can be used to reduce the time of a wash program. It is best used on lightly soiled loads.
3. Rinse+ (2)
   • Additional Rinse for better washing quality.
4. Delay End (C)
   • You can set a time delay so that the washing machine will start automatically and finish after a specified time interval.
5. Add Item (Laundry can be added or removed after the washing program is started.
6. Press the Add Item button when the LED is turned on. Add or remove laundry. Close the door and Press the Start/Pause button.

NOTE
For safety reasons, the door remains locked when the water level or temperature is high. It is not possible to add laundry during this time.  If the water temperature in the drum is high, wait until it cools down.

CAUTION

• When adding laundry, make sure to completely push it into the drum. If laundry gets stuck in the door latch hole, the rubber packing may be damaged, causing water leakage and malfunction.
• Forcing the door open may cause part damage, destruction, or safety problems.
• If you open the door while there are a lot of suds and water in the drum, the suds or water may flow, causing burn injury or a wet floor.
• The required lamp will light up for identification. Pre Wash (L
• If the laundry is heavily soiled, the Pre Wash program is recommended (Press for about three

How to use a washer

• Tub Clean (G)

Tub Clean course can be set by pressing *Tub Clean (About three seconds). When Tub Clean course is set. displav

Tub Clean
Tub Clean course can be set by pressing *Tub Clean (About three seconds) When Tub Clean course is set, display ” t cl”.

ECL
TUB CLEAN is a special cycle to clean the inside of the washer. This cycle uses a higher water level with a higher spin speed. Perform this cycle regularly.

How to use the Tub Clean cycle

1. Remove any clothing or items from the washer and close the door.
2.  Open the dispenser drawer and add Anti limescale (Calgon) to the main wash compartment.

How to use a washer

• Tub Clean (€ )
• Time Save
• Tub Clean
• Tub Clean course can be set by pressing *Tub Clean (About three seconds)
• When Tub Clean course is set, display ” t ct”

EEL
TUB CLEAN is special cycle to clean inside of the washer. This cycle uses a higher water level with higher spin speed. Perform this cycle regularly.

How to use the Tub Clean cycle

1. Remove any clothing or items from the washer and close the door.
2. Open the dispenser drawer and add Anti limescale (Calgon) to the main wash compartment.
   NOTE: Do not add any detergent to the detergent compartments. Excessive suds may generate & leak from the washer.

NOTE: Do not add any detergent to the detergent compartments. Excessive suds may generate & leak from the washer. Power on and then press and hold Tub Clean. for 3 seconds. then ” t cl ” is displayed in LED. Press the Start/Pause button to start. After the cycle is complete, leave the door open so that moisture present inside the washer can dry.

CAUTION
If there is a small child, be careful not to leave the door open for too long.

Crease Care (2)
If you want to prevent creasing, the Crease Care program is recommended (Press for about three seconds).

Child Lock
If you choose to lock the buttons on the control assembly to prevent tampering this function may be selected. Child Lock can be set by pressing the “Child Lock (About three seconds)

• Delay End
• Child Lock LABEL
• To deactivate the Child Lock system, press
• Child Lock again.
• (About three seconds)
• Delay End
• Child Lock 18:88

To change to the desired program, whilst in child lock mode.

1. Press *Child Lock once again. (About three seconds)
2. Press the Start/Pause button.
3. Select the desired program and press the
4. Start/Pause button again.

Delay End
Change the desired program The child lock can be set at any time and it can be deactivated only by using child lock cancel process. Turning the power off and operational errors will not affect child lock.

Spin selection

• Spin Speed is available according to the program as follows [FHT1207SNW/L/S, FHT1265SNW/L/S]
• Cotton, Cotton+, Download Cycle, Mix, Allergy Care
• Stain Care, Dark Wash, Quick 30
• No-400-800-1000-1100-1200
• Silent Wash, Easy Care, Duvet, Baby Steam Care
• No-400-800-1000
• Sports Wear, Gentle Care
• No-400-800 [FHT1065SNW/L/S, FHT1006SNW/L/S, FHT1006HNW/L/S]
• Cotton, Cotton+, Download Cycle, Mix, Allergy Care
• stain Care, Dark Wash, Quick 30
• No-400-600-800-900-1000
• Silent Wash, Easy Care, Duvet, Baby Steam Care
• No-400-600-800
• Sports Wear, Gentle Care
• No-400-600

After selecting the spin course, the spin speed can be chosen by pressing the spin button.

No spin
If No spin is selected, the washer stops after draining water. The required lamp will light up for identification.

Water Temp
Cold 20°c 30°c (40°c 60°c 95°C

Temp
By pressing the Temp. button, the water temperature can be selected.
Cold 20°C/ 30°C / 40°C / 60°C / 95°C

Water temperature can be selected according to the program. For identification, the literature lamp will light up For more detailed information, please refer to page 14.

• Delay End300
• Delay End500

Delay End
Preparing washing before starting “Delay End”

• Turn on the water tap.
• Load laundry and close the door.
• Place the detergent and fabric softener in the drawer.
• How to set ” Delay End”
• Press Power button.
• Turn the Program dial to select the program you require.
• Press Delay End button and set the desired time.
• Press the Start/Pause button. (blinks.)
• If Delay End button is pressed, “3:00” is displayed. The maximum delayed time is 19 hours and the minimum time is 3 hours.
• Each pressing of the button advances on time delay by one hour.
• To cancel the Delay End, press the Power button.- Press Power button.
• Turn the Program dial to select  the program you require.
• Press Delay End button and set the desired time.
• Press the Start/Pause button.
• If Delay End button is pressed, “3:00” is displayed. The maximum delayed time is
• hours and the minimum time is 3 hours.
• Each pressing of the button advances on time delay by one hour.
• To cancel the Delay End, press the Power button.
• Delay End is ‘expected time’ from the present to the completion of washing cycle or selected process (Wash, Rinse, Spin).
• According to the condition of water supply and temperature, the delayed time and the actual washing time may vary.

Display

Special function display
When child lock is selected, the ” [L” is displayed. When time delay is selected, it shows the remaining time to finish the selected program.

Self-diagnosis display
If the machine encounters a fault during the operation, the associated fault will be displaced. If these error letters are displayed, please refer to the troubleshooting page and follow the guide.

Completion of washing
When washing cycle is completed, “End ” is displayed on the “Multi display”.

Time left

• During the washing cycle, the remaining washing time is displayed.
• The washing time may vary by the amount of laundry, water pressure, water temperature, and other washing conditions.
• If an unbalanced load is detected or if the suds-removing program operates, the wash time may be extended.

Using the Tag On Function
Conveniently use the Smart Diagnosis ™ to communicate with the appliance directly from a smartphone. The Tag On function can only be used with most smartphones equipped with the NFC (Near Field Communication) function and
based on the Android OS (operating system).

Installation of the Application
Search LG SmartThinQ application on the Google Play Store or Apple App Store from your smartphone.

LG Smart
Using the Application LG SmartThinQ application allows you to use various features for your convenience.

• Cycle Download

• Smart Diagnosis ™

• Tag On Cycle Set

• Laundry Stats
  NOTE

• Press 12/ in the LG SmartThinQ application for a more detailed guide on how to use the Tag On function.

• Depending on the smartphone manufacturer and Android OS version, the NFC activation process may differ. Refer to the manual of your smartphone for details.

• Because of the characteristics of NFC, if the transmission distance is too far, or if there is a metal sticker or a protective case on the phone, the transmission will not be good.

• In some cases, NFC-equipped phones may be unable to transmit successfully.

• The content found in this manual may differ depending on the version of LG SmartThinQ application, and it may be modified without notice to users.

• Download Cycle Download new and special cycles that are not included in the basic cycles on the appliance. Appliances that have been successfully registered can download a variety of specialty cycles specific to the appliance.

• Only one cycle can be stored on the appliance at a time.

• Once cycle download is completed in the appliance, the product keeps the downloaded cycle until a new cycle is downloaded.

Maintenance

Before cleaning the washer interior, unplug the electrical power cord to avoid electrical shock to avoid electrical shock hazards. When disposing of the appliance, cut off the mains cable, and destroy the plug. Disable the door lock to prevent young children being trapped inside.

The water inlet filter
IE ” error message will blink on the control panel when water does not enter the detergent drawer. If water is very hard or contains traces of lime deposit, the water inlet filter may become clogged. It is therefore a good idea to clean it from time to time.

1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter using a hard bristle brush.
4. Tighten up the inlet hose.

The drain pump filter
The drain filter collects threads and small objects left in the laundry. Check regularly that the filter is clean to ensure the smooth running of your machine.
CAUTION First drain using the drain hose and then open the pump filter to remove whatever any threads or objects. Be careful when draining if the water is hot. llow the water to cool down before cleaning the drain pump, carrying out
emergency emoting or opening the door in an emergency

1. Open the lower cover cap (®) by using a coin. Drain plug (2) to pull out the hose.
2. Unplug the drain plug (®), allowing the water to flow out. At this time use a vessel to prevent water flowing on to the floor. When water does not flow any more, turn the pump filter (3) open to the left.
3. Remove out any foreign material from the pump filter (3).
4. After cleaning, turn the pump filter (3)clockwise and insert the drain plug (2)to the original place. Close the lower cove r cap.

Dispenser drawer

• After a while detergents and fabric softeners leave a deposit in the drawer.
• It should be cleaned from time to time with a jet of running water.
• If necessary it can be removed completely from the machine by pressing the latch downwards and by pulling it out.
• To facilitate cleaning, the upper part of the fabric softener compartment can be removed.

The drawer recess

• Detergent can also accumulate inside the recess which should be cleaned occasionally with an old toothbrush.
• Once you have finished cleaning, replace the drawer and run a rinse cycle without laundry.

The washing drum

• If you live in a hard water area, limescale may continuously build up in places where it cannot be seen and thus not easily removed.
• Over time the build-up of scale clogs appliances, and if it is not kept in check these may have to be replaced.
• Although the washing drum is made of Stainless steel, specks of rust can be caused by small metal articles (paper clips, safety pins) that have been left in the drum.
• The washing drum should be cleaned from time to time.
• If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine use.
• Descaler may contain chemicals that may damage part of your washing machine.
• Remove any spots with a stainless steel cleaning agent.
• Never use steel wool.

Cleaning your washer

Exterior
Proper care of your washer can extend its life. The outside of the machine can be cleaned with warm water and a neutral nonabrasive household detergent. Immediately wipe off any spills. Wipe with damp cloth. Try not to hit the surface with sharp objects.
IMPORTANT : Do not use methylated spirits, diluents or similar products.

Interior
Dry around the washer door opening, flexible gasket, and door glass.  Run the washer through a complete cycle using hot water. Repeat process if necessary.
NOTE Remove hard water deposits using only deans labeled as washer safe.

Cold condition
If the washer is stored in an area where freezing may occur or moved in freezing temperatures, follow these instructions to prevent damage to the washer:

1. Turn off water supply tap.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1gallon(3.8L) of nontoxic recreational vehicle(RV) antifreeze into an empty wash drum. Close the door.
5. Set spin cycle and let washer spin for 1 minute to drain out all water. Not all of the RV antifreeze will be expelled.
6. Unplug electrical power cord, dry the drum interior, and close the door.
7. Remove dispenser drawer drain and dry excessive water from the compartments.
8. Store washer in an upright position.
9. To remove antifreeze from washer after storage, run empty washer through a complete cycle using detergent. Do not add wash load.

Troubleshooting guide

This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately When the machine does not function properly or does not function at all, check the following points before you contact your service provider.

If noise continues after washer is restarted, call your authorised service centre.

Thumping sound| •  Heavy wash loads may produce a thumping sound. This is usually normal.| If sound continues, washer is probably out of balance. Stop and redistribute wash load.
Vibrating noise| • Have all the transit bolts and packing been removed?

•  Are all the feet resting firmly on the ground?

| If not removed during

installation. Refer to Installation guide for removing transit bolts.

Wash load may be unevenly distributed in drum. Stop washer and rearrange wash load.

Water leaks

Oversudsing

Water does not enter washer or it enters slowly

Water in the washer does not drain or drains slowly

| • Fill hoses or drain hose are loose at tap or washer.

•  House drain pipes are clogged.

•  Water supply is not adequate in area.

• Water supply tap is not completely open.

•  Water inlet hose(s) are kinked.

•  The filter of the inlet hose(s) clogged.

•  Drain hose is kinked or clogged.

•  The drain filter is clogged.

| Check and tighten hose connections.

Unclog drain pipe. Contact plumber if necessary.

Too much detergent or unsuitable detergent may cause excessive foaming which may result in water leaks.

Check another tap in the house. Fully open tap.

Straighten hose.

Check the filter of the inlet hose.

Clean and straighten the drain hose. Clean the drain filter

Washer does not start

Washer will not spin

| • Electrical power cord may not be plugged in or connection may be loose.

• House fuse blown, circuit breaker tripped,or a power outage has occurred.

• Water supply tap is not turned on.

• Check that the door is firmly shut.

| Make sure plug fits tightly in wall outlet.

Reset circuit breaker or replace fuse. Do not increase fuse capacity.

If problem is a circuit overload, have it corrected by a qualified electrician. Turn on water supply tap.

Close the door and press the StarVPause button. After pressing the StarVPause button, it may take a few moments before the clothes washer begins to spin. The door

must lock before spin can be achieved.

Add 1 or 2 similar items to help balance the load.

Rearrange load to allow proper spinning

Door does not open| | Once machine has started, the door can not be opened for safety reasons. Check if the “Door Lock” icon is illuminated. You can safely open the door after the “Door Lock” icon

turns off.

Wash cycle time delayed| | The washing time may vary by the amount of laundry, water pressure, water temperature and other usage conditions.

If the imbalance is detected or if the suds removing program works, the wash time shall be increased.

Fabric softner overflow| • Too much softener may cause an overflow.| Follow softener guidelines to ensure appropriate amount is used.

Do not exceed the maximum fill line.

Softeners dispensed too early| | Close the dispenser drawer slowly. Do not open the drawer during the wash cycle.

Dry problem

| ****

Check water supply tap.

| •   Do not overload. Check that the washing machine is draining properly to extract adequate water from the load. Clothes load is too small to tumble properly. Add a few towels.

•  Turn off water supply tap.

• SMARTDIAGNOSIS™ function is available only for the products with a SMARTDIAGNOSIS™ mark.
• In case of a mobile phone with static option, the SMARTDIAGNOSIS™ function might not operate.
• Using SMARTDIAGNOSIS™
• only use this feature when instructed to do so by the call center.
• The transmission sounds similar to a fax machine, and so has no meaning except to the call center.

Using SMARTDIAGNOSIS™
cannot be activated if the washer does not power up.

• If this happens, then troubleshooting must be done without SMARTDIAGNOSIS™.
• If you experience problems with your washer, call to Customer Information Center.
• Follow the call center adent’s instructions and do the following stens when requested.

1. Press the Power button to turn on the washer.
2. Do not press any other buttons or turn the cycle selector knob.
3. When instructed to do so by the call center,  place the mouthpiece of your phone very close to the Power button.
4. Press and hold the “Temp.” button for six seconds, while holding the phone mouthpiece to the icon or Power button.
5. Keep the phone in place until the tone transmission has finished. This takes about 6 seconds, and the display will count down the time.
6. For best results, do not move the phone while the tones are being transmitted.
7. If the call center agent is not able to get an accurate recording of the data, you may be asked to try again.
8. Pressing the Power button during the transmission will shut off the SMARTDIAGNOSIS™.
9. Once the countdown is over and the tones have stopped, resume your conversation with the call center agent, who will then be able to assist you using the information transmitted for analysis at the call to Customer Information Center.

Terms of Warranty

What Is Not Covered

• Service trips to your home to teach you how to use the product.
• If the product is connected to any voltage other than that shown on the rating plate.
• If the fault is caused by accident, neglect, misuse or Act of God.
• If the fault is caused by factors other than normal domestic use or use by the owner’s manual.
• Provide instruction on use of product or change the set-up of the product.
• If the fault is caused by pests for example, rats or cockroaches etc..
• Noise or vibration that is considered normal for example water drain sound, spin sound, or warming beeps.
• Correcting the installation for example, levelling the product, adjusting of drain.
• Normal maintenance which recommended by the owner’s manual.
• Removal of foreign objects/substances from the machine, including the pump and inlet hose filter for example, grit, nails, bra wires, buttons etc.
• Replace fuses in or correct house wiring or correct house plumbing.
• Correction of unauthorized repairs.
• Incidental or consequential damage to personal property caused by possible defects with this appliance.
• If this product is used for commercial purpose, it is not warranted.
• (Example: Public places such as public bathroom, lodging house, training center, dormitory)
• If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product, or the replacement of a defective part, shall be borne by the owner.

Disposal of your old appliance (as per e-waste Rules)

1. When this crossed-out wheeled bin symbol is depicted on the product and its operator’s manual, it means the product is covered by the e-waste Management and Handling Rules, 2011 and are meant to be recycled, dismantled, refurbished or disposed off.

2.  Dos

   • The product is required to be handed over only to the authorized recycler for disposal.
   • Keep the product in an isolated area, after it becomes non-functional/un-repairable so as to prevent its accidental
     breakage.

3. Don’t

   • The product should not be opened by the user himself/herself, but only by authorized service personnel.
   • The productis not meant for re-sale to any unauthorized agencies/scrap dealer/ kabariwalah.
   • The product is not meant for mixing into household waste stream.
   • Do not keep any replaced spare parts) from the product in the exposed area.

4. Any disposal through unauthorized agencies/person will attract action under the Environment (Protection) Act 1986 .

5. This product does not contain any of the hazardous substances as specified in rule 13(1) and (2) of the e-waste ( Management and Handling) Rules, 2011.

6. To locate the nearest collection centre or call for pick-up (limited area only) for disposal of this appliance, please contact Toll-Free No. 1800-315-9999 / 1800-180-9999 for details. All collection centre and pick up facilities are done by third parties with LG Electronics India Pvt. Ltd merely as a facilitator.

For more detailed information, please visit: http://www.lq.com/in

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>