LG LSW400BG Wall Mounting Bracket Owner’s Manual

LG LSW400BG Wall Mounting Bracket

Product Information

Specifications

• Model Numbers: LSW200B, LSW200BG, LSW200BX, LSW200BXG, LSW400B, LSW400BG
• Warranty: 1 Year
• Component List:
  • Wall mount anchor: 4 units
  • Wall mount screw: 10 units (LSW200B/LSW200BG), 4 units (LSW200BX/LSW200BXG), 6 units (LSW400B/LSW400BG)
  • Guide spacer: 4 units
  • Guide space screw: 4 units (LSW200B/LSW200BG/LSW400B/LSW400BG – M6X18mm, LSW200BX/LSW200BXG – M6X28mm)
  • Safety clip: 2 units
  • Safety clip screw: 2 units (M4X12mm)
  • PVC Washer: 4 units
  • Set protection cushion: 4 units
  • User manual

Product Usage Instructions

Safety Precautions

Before proceeding with the installation, please read and follow these important safety instructions:

• Read and keep the instructions for future reference.
• Follow all instructions and heed all warnings.
• The wall mount should be installed by a trained and experienced installer designated by the retailer.
• Do not install the product where the weight cannot be supported.
• Use a trained and experienced installer to move or replace the wall mount if needed.
• Do not hang on the product or apply severe impact after installation.
• Never hang the power or signal cable on the rear side of the TV during installation.

Installation

To ensure proper installation and avoid safety issues, follow these steps:

1. Refer to the user manual for detailed installation directions.
2. Check the type of wall material and use the sealed anchor and screw provided if the conditions comply.
3. Do not use a wet towel to wipe the product, and do not use any heater or humidifier below where the product is installed.

Wall Mounting

Follow these steps to mount the product on the wall:

1. Ensure that the wall is strong enough to support the weight of the product.
2. Attach the wall mount anchor to the wall using the provided wall mount screws.
3. If using LSW200BG/LSW200BXG or LSW400BG Wall Mounts, angled adapters may be required due to shallow clearance between the display and the wall. Note that these adapters may block other connections on the back of the TV.
4. Make sure the connectors on the cables connected to the display do not press against the wall.
5. Securely attach the guide spacers to the wall mount using the guide space screws.
6. Attach the safety clips to the wall mount using the safety clip screws.
7. Place the PVC washers on the wall mount screws.
8. Attach the set protection cushions to the wall mount.
9. Refer to the user manual for additional instructions on attaching the TV to the wall mount.

FAQ

• Q: What should I do if my wall is not strong enough to support the weight of the product?
  A: If the strength of the location where the wall mount is installed is not strong enough, do not proceed with the installation. Consult a professional or use an alternative mounting method.

• Q: Can I install the wall mount on any type of wall?
  A: The type of wall material should be checked before installation. Use the provided sealed anchor and screw if the conditions comply. Using the designated anchor and screw ensures the mount can withstand the weight of the product and prevents safety issues.

• Q: Can I wipe the product with a wet towel?
  A: No, it is not recommended to wipe the product with a wet towel. This can cause a fire, electric shock, or damage to the product. Use a dry cloth for cleaning.

Please read this manual carefully before operating your set and retain it for future reference

• LSW200B
• LSW200BG
• LSW200BX
• LSW200BXG
• LSW400B
• LSW400BG

P/NO : MFL63640502 (1101-REV03)

Warranty

1 Year Warranty
If material or workmanship proves defective under normal use, during the warranty period, please contact the retailer where you purchased it. This warranty is good only to the original purchaser of the product and is effective only in the local area

Component

Due to the shallow clearance between the display and the wall, the LSW200BG/LSW200BXG and LSW400BG Wall Mounts may require the use of the included angled adapters

Component cable with angled connectors

HDMI angle adapter

• Note that the included angle adapters may block other connections on the back of the TV.
• Make sure the connectors on the cables connected to the display do not press against the wall.

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions

Warning

• This wall mount should be installed by a trained and experienced installer designated by the retailer. Having the product installed by a non-specialized installer is very dangerous and can cause damage or injury

• Use a trained and experienced installer to move or replace the wall mount, if needed.
  Installation requires special techniques and moving or installing the product on your own can cause serious safety issues.

• When installing the wall mount, never hang the power or signal cable on the rear side of the TV.
  The cord can be damaged and cause a fire, an electric shock, or damage to the product

• Do not install the product where the weight cannot be supported.
  If the strength of the location where the wall mount is installed is not strong enough, it can fall off and cause an injury.

• After installing the wall mount, do not hang on the product or apply severe impact to the product.
  The product can fall off and cause injury.

Caution

• Install the product according to the directions in the user manual.
  If the product is not installed based on the directions in the user manual, it can cause serious injury or damage to the product.

• During the installation, check the type of wall material and use the sealed anchor and screw if the conditions comply.
  If you do not use the designated anchor or screw, the mount may not be able to withstand the weight of the product and cause a safety issue.

• Do not wipe the product with a wet towel and do not use any heater or humidifier below where the product is installed.
  If water flows into the product or if moisture and heat are applied to the product, it can cause a fire, an electric shock, or a problem to the product.

• Unplug the power cord from the power outlet before
  installing the product.
  If you install the product with the power cord plugged in, it can cause an electric shock or a fire.

• Do not allow the video connectors connected to the display to press against the wall. Use the included right-angle adapters if needed.
  Only use attachments/accessories specified by the manufacturer.

• When installing the product or adjusting the height of the product after installing, always do so with 2 people. Working alone can cause the product to fall off and result in injury or damage to the product.

• When drilling holes in the wall, always use a drill bit and drill of a designated diameter. Also, follow the designated directions for the depth of the hole.
  If the product is installed without following the designated method, the product may be unstable and cause a safety issue.

• Do not install the product near any object that may cause vibration.
  Do not install the product near any high-voltage power cable or power source.

• Do not install the product with bare hands. Always wear proper work gloves.
  It can cause an injury.

Before installation

• Do not use the product for purposes other than mounting a display on the wall.

• When installing/using the wall mount, be cautious of product damage and avoid accidents.

• If you have not fully read and understood the installation manual, do not install the product and contact the dealer to have a specialized installer install the product for you.

• Even if you are not a specialized installer, it is advantageous to have experience in the mechanical or construction field in completely understanding this manual and installing the product.

• This product is designed to be mounted to walls that use standard intervals between the studs.

• Install the screw to attach the wall mount so that it can be assembled at the center from both ends of the studs.
  The use of a stud finder, a separate device, is recommended.

• Install the product only on a vertical wall.
  The manufacturer is not responsible for issues from installing the product on severe walls or the ceiling.

• Keep the included accessories out of reach of babies or children as it can cause safety issues including suffocation from swallowing the parts.

• Make sure screws are tight against the wall, but do not overtighten.

• Be careful not to install a TV that exceeds the weight restrictions of the wall mount.

• Be careful with the tools used during installation to prevent accidents or damage.

Installation method

• Tools you will need: Phillips head “+” driver(Manual or motorized) Ø4mm drill bit for wood or steel / Level / Stud finder / Drill. You may also need an 8mm socket wrench or an 8mm drill bit for concrete.
• The installation method is described based on the LSW200B model. The actual product may differ from the picture.

Fixating the mounting bracket on the TV

If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the technical service manual.

Work procedure

1. Check to see if the display has screws installed into the mounting holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer screw in order as shown in the picture.
3. Assemble the guide spacer to the set by tightening the screw.
4. Tighten the screw until the set, guide spacer and the screw are fully pressing against one another.
5. Use the “+” driver (Manual or motorized) when tightening the screw.

How to attach to masonry walls

Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick, and hallow blocks that do not crack.

Please follow the below direction.

• Check the material of the wall and the thickness of the finishing.
• When installing the product on the wooden wall, refer to page 5.
• When installing the product on wall material not designated, install the product so that each fixated location can withstand the pull-out load of 70kgf (686N) and shear load of 10kgf (980N) or above.
• Use the Ø8mm drill bit for concrete and hammer (Impact) drill.
  • a. Use a drill bit Ø8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm
  • b. Clean the drilled hole.
  • c. Insert the sealed anchor into the hole. (When inserting the anchor, use a hammer.)
  • d. Set the wall mount on the wall by aligning it to the location of the hole. and, set the angle adjusting part to face upward.
  • e. Align the wall mount bolt to the hole and tighten it. At this time, the bolt must be tightened with a torque of 45kgf/cm or above.

How to install the wall mount

When installing on a masonry wall
When you separate the 8 screws on the wall mount connected to the wall bracket for use with a wooden wall, it is much easier to install the product.

• When installing the product on a masonry wall, turn the 8 screws on the A part counterclockwise to separate the screw and bracket.
• After aligning the wall bracket to the location to install, mark the part to screw on the wall and then remove the wall bracket.
• Refer to page 4 to attach the wall bracket.
• Use a level to check whether the wall mount is level.
• If the screw cannot be assembled in the designated location inevitably, it can be assembled by rearranging to the closest location. But, do not change 2 or more locations from the designated spot.
• LSW200B/LSW200BG/LSW200BX/LSW200BXG: Assemble the wall mount screw on 1 left and 1 right location on the top part and 1 left and 1 right location on the bottom part.
• LSW400B/LSW400BG: Assemble the wall mount screw on 2 left and 2 right locations on the top and 1 left and 1 right location on the bottom part.
• At this time, use a “+” driver (Manual or motorized) or 8mm wrench to tighten the screw so that the wall, wall bracket, and screw are completely pressed against one another.

When mounting to wooden studs

• a. Locate and mark the centers of the wall studs using a stud finder.
• b. After aligning the wall bracket on the wall where the center of the wood stud is marked, mark the location of the screws and then remove the wall bracket.
• c. Use a level to make sure your screw marks are level.
• d. Use the 4mm drill bit for wood to drill holes with a depth of 76mm or above where the wall mount screw location is marked on the wall.
• e. Clean the drilled hole.
• f. Tighten the wall mount screws for the wall bracket on the drilled hole.
  • At this time, tighten the screw so that the wall, wall bracket, and wall mount screw are pressed against one another. (Drywall can be damaged when tightened with excessive force, please be careful.)
  • When tightening the screw use the “+” driver (Manual or motorized) or 8mm wrench.

How to assemble the wall mount support and display

Always install the display with 2 or more people.

1. Set the display with the guide spacer assembled on the wall mount bracket in the wall in the arrow direction. At this time, align the bottom assembly part and lift the setup lightly to align the top part.
2. When adjusting the location, assemble the provided safety clip as shown in the picture to prevent the product from moving. Tighten the safety clip screw completely. If the safety clip is not tightened as shown in the picture, the product can fall off.
3. Pull on the bottom of the set to make sure the display is secure.
4. When installing a display rotated, only rotate the display 90 degrees (portrait mode). (Only applies for VESA 200X200, 400×400)
5. The clearance from the wall is 14mm for this product. Make sure to keep a certain level of distance from the wall so that excessive force is not applied to the cable or accessory.
6. When you push the product with excessive force, the product can be damaged.

How to Level the Display

After installing the display, check to make sure it is level. The wall mount has two screws that make minor adjustments to the level.

Cable arrangement and set protection cushion

• Arrange the cables as shown in the picture. Use some type of cable banding device to hold all the cables together.
• Attach the set protection cushion to mitigate the impact between the wall and the set when adjusting the angle. Attach the set protection cushion as shown in the picture.

Product specification

With the bracket removed

With the bracket attached

LSW200B/LSW200BG/LSW200BX/LSW200BXG

LSW400B/LSW400BG

The model and serial number of the product are located on the back or one side of the product. Record it below should you ever need service.

MODEL
SERIAL

Supported Displays
(Consult the retailer for a detailed list of models.)
LSW200B/LSW200BG Supports
: 37 – LZ, LW, LV series 47/46/42/37 – LD, LE, LX, LK series
LSW200BX/LSW200BXG Supports : 47LE95/47LX95/47LX98*
LSW400B/LSW400BG Supports : 60/55/52/47/46/42 -LZ, LW, LV series
60/55/52 – LD, LE, LX, LK series
www.lg.com

References

• LG Electronics & Home Appliances | Shop Now | LG USA
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>