5100A Series Shop Moxa Industrial Networking Installation Guide
- June 16, 2024
- MOXA
Table of Contents
2019 Moxa Inc. All rights reserved.
NPort 5100A Series
Quick Installation Guide
Version 3.3, December 2019
Overview
NPort 5100A series device servers are compact, palm-sized data communication
devices that allow you to control RS-232 (NPort 5110A), RS-422/485 (NPort
5130A), and RS-232/422/485 (NPort 5150A) serial devices over a TCP/IP-based
Ethernet.
NOTE “-T” indicates an extended temperature model.
Package Checklist
Before installing the NPort 5100A series device server, verify that the package contains the following items:
- 1 NPort 5100A serial device server
- 100 to 240 VAC power adapter (excluding T models)
- 4 stick-on pads
- Quick Installation Guide
- Product Warranty Statement
Optional Accessories
- DK-35A: DIN-Rail Mounting Kit (35 mm)
NOTE Notify your sales representative if any of the above items are
missing or damaged.
NOTE The operating temperature of the power adapter in the box is from 0
to 40°C. If your application is out of this range, please use a power adapter
supplied by UL Listed External Power Supply (The power output meets SELV and
LPS and rated 12 – 48 VDC, minimum current 0.73 A). Moxa has power adapters
with wide temperature range (-40 to 75°C, -40 to 167°F), the PWR-12150-(plug
type)-SA-T series, for your reference.
Hardware Introduction
As shown in the following figures, NPort 5100A series device servers have one
male DB9 port for transmitting RS-232 (NPort 5110A), RS422/485 (NPort 5130A),
or RS-232/422/485 (NPort 5150A) serial data. NOTE The NPort 5110A, NPort
5130A, and NPort 5150A have the same form factor.
Reset Button —Press and hold the Reset button for 5 seconds to load
factory defaults: Use a pointed object, such as a straightened paper clip or
toothpick, to depress the reset button. This will cause the Ready LED to blink
on and off. The factory defaults will be loaded once the Ready LED stops
blinking (after about 5 seconds). At this point, release the reset button.
LED Indicators— The NPort 5100A’s top panel has three LED indicators,
described in the following table.
| LED Name | LED Color | LED Function |
|---|---|---|
| Ready | Red | Steady on: |
| Blinking: | Indicates an IP conflict, or DHCP or BOOTP server is not responding |
properly.
Green| Steady on:| Power is on and the NPort is functioning normally.
Blinking:| The NPort has been located by the NPort Administrator’s Location
function.
Off| Power is off, or a power error.
Link| Orange| 10 Mbps Ethernet connection.
Green| 100 Mbps Ethernet connection.
Off| Ethernet cable is disconnected.
Tx/Rx| Orange| Serial port is receiving data.
Green| Serial port is transmitting data.
Off| Data is not being transmitted or received through the serial port.
Adjustable pull high/low resistor for RS-422/485 (150 KΩ or 1 KΩ) Jumpers are used to set the pull high/low resistor values. The default is 150 KΩ. Short the jumpers to set this value to 1 KΩ. Do not use the 1 KΩ setting with RS-232 mode, since doing so will degrade the RS-232 signals and shorten the communication distance.
Hardware Installation Information
STEP 1 : After removing the NPort 5100A series device server from the
box, connect the NPort 5100A series device server to a network. Use a standard
straight-through Ethernet cable to connect to a hub or switch.
When setting up or testing the NPort 5100A series device server, you might
find it convenient to connect directly to your computer’s Ethernet port. In
this case, use a cross-over Ethernet cable.
STEP 2: Connect the NPort 5100A series device server’s serial port to a
serial device.
STEP 3 : Connect the power adaptor.
STEP 4: Placement options.
In addition to placing the NPort 5100A on a desktop or other horizontal
surface, you may also make use of the DIN-Rail or Wall Mount options, as
illustrated below.
NOTE The operating temperature of the power adapter in the box is from 0
to 40°C. If your application is out of this range, please use a power adapter
supplied by UL Listed External Power Supply (The power output meets SELV and
LPS and rated 12 – 48 VDC, minimum current 0.73 A). Moxa has power adapters
with wide temperature range (-40 to 75°C, -40 to 167°F), the PWR-12150-(plug
type)-SA-T series, for your reference.
Software Installation Information
For the NPort’s configuration, the default IP address of the NPort is:
LAN: Static IP = 192.168.127.254; netmask = 255.255.255.0
You may log in with the default account and password (account: admin;
password: moxa) to change any settings to meet your network topology (e.g., IP
address) or serial device (e.g., serial parameters). If you would like to
apply the Real COM mode to your
application, you will need to install NPort’s driver on your desktop. You may
also refer to Moxa’s support website https://www.moxa.com/support for the
user’s manual, driver, SNMP MIB, and NPort Search Utility.
NOTE For the NPort with DB Male serial ports, you may refer to DB9 Male
Ports pin assignment section to loop back pin 2 and pin 3 for the RS-232
interface to carry out a self test on the device.
Pin Assignments
Ethernet Port Pinouts
| Pin No. | Ethernet |
|---|---|
| 1 | Tx+ |
| 2 | Tx- |
| 3 | Rx+ |
| 4 | Rx- |
NPort 5110A—DB9 male (RS-232) port pinouts
| Pin No. | RS-232 |
|---|---|
| 1 | DCD |
| 2 | RxD |
| 3 | TxD |
| 4 | DTR |
| 5 | GND |
| 6 | DSR |
| 7 | RTS |
| 8 | CTS |
| 9 | – |
NPort 5130A—DB9 male (RS-422/485) port pinouts
| Pin No. | RS-422/485-4W | RS-485-2W |
|---|---|---|
| 1 | TXD-(A) | – |
| 2 | TXD+(B) | – |
| 3 | RXD+(B) | Data+(B) |
| 4 | RXD-(A) | Data-(A) |
| 5 | GND | GND |
| 6 | – | – |
| 7 | – | – |
| 8 | – | – |
| 9 | – | – |
NPort 5150A—DB9 male (RS-232/422/485) port pinouts
| Pin No. | RS-232 | RS-422/485- 4W | RS-485-2W |
|---|---|---|---|
| 1 | DCD | TXD-(A) | – |
| 2 | RxD | TXD+(B) | – |
| 3 | TxD | RXD+(B) | Data+(B) |
| 4 | DTR | RXD-(A) | Data-(A) |
| 5 | GND | GND | GND |
| 6 | DSR | – | – |
| 7 | RTS | – | – |
| 8 | CTS | – | – |
| 9 | – | – | – |
Specifications
Power Requirements
Power Input| 12 to 48 VDC
Power Consumption| NPort 5110A:
82.5 mA @ 12V, 47.3 mA @ 24V NPort 5130A:
89.1 mA @ 12V, 49.5 mA @ 24V NPort 5150A:
92.4 mA @ 12V, 52.8 mA @ 24V
Environmental Limits
Operating Temperature| Standard Models:
0 to 60°C (32 to 140°F) Wide Temp. Models:
-40 to 75°C (-40 to 167°F)
Ambient Humidity| 5 to 95% RH
Dimensions
With ears| 75.2 x 80 x 22 mm (2.96 x 3.15 x 0.87 in)
Without ears| 52 x 80 x 22 mm (2.05 x 3.15 x 0.89 in)
Protection
Serial Line Protection| Level 1 Surge, EN 61000-4-5
Magnetic Isolation| 1.5 kV for Ethernet
Power Line Protection| Level 2 Burst (Er), EN 61000-4-4 Level 3 Surge, EN
61000-4-5
Regulatory Approvals
FCC Class A, CE Class A, UL, LVD
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel: 1-714-528-6777
Fax: 1-714-528-6778
Moxa Europe:
Tel: +49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99
Moxa India:
Tel: +91-80-4172-9088
Fax: +91-80-4132-1045
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel: +86-21-5258-9955
Fax: +86-21-5258-5505
Moxa Asia-Pacific:
Tel: +886-2-8919-1230
Fax: +886-2-8919-1231
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>