OMNITRONIC MZD-88 Matrix Zone Distributor User Manual

OMNITRONIC MZD-88 Matrix Zone Distributor

Operating instruction

Important Information

CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!

For your own safety, please read this user manual carefully before you initially start-up.

Every person involved with the installation, operation and maintenance of this device has to

• be qualified
• follow the instructions of this manual
• consider this manual to be part of the total product
• keep this manual for the entire service life of the product
• pass this manual on to every further owner or user of the product
• download the latest version of the user manual from the Internet

INTRODUCTION

Thank you for having chosen the OMNITRONIC Matrix Zone Distributor MZD-88. You have acquired a reliable and powerful device. If you follow the instructions given in this manual, we can assure you that you will enjoy this device for many years.

Unpack your OMNITRONIC MZD-88.

SAFETY INSTRUCTIONS

CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires!

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual.

Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems.

If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature.

Please make sure that there are no obvious transport damages. Should you notice any damages on the A/C connection cable or on the casing, do not take the device into operation and immediately consult your local dealer.

This device falls under protection-class I. The power plug must only be plugged into a protection class I outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or power outlets can lead to the destruction of the device and to mortal electrical shock.

Always plug in the power plug least. The power plug must always be inserted without force. Make sure that the plug is tightly connected with the outlet.

Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Never touch them with wet hands, as this could lead to mortal electrical shock.

Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate next to sources of heat or cold. Disregard can lead to power cord damages, fire or mortal electrical shock.

The cable insert or the female part in the device must never be strained. There must always be sufficient cable to the device. Otherwise, the cable may be damaged which may lead to mortal damage.

Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord from time to time.

If extension cords are used, make sure that the core diameter is sufficient for the required power consumption of the device. All warnings concerning the power cords are also valid for possible extension cords.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord. Otherwise, the cable or plug can be damaged leading to mortal electrical shock. If the power plug or the power switch is not accessible, the device must be disconnected via the mains.

If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then be cleaned with a dry cloth. Dust can reduce the insulation which may lead to mortal electrical shock. More severe dirt in and at the device should only be removed by a specialist.

There must never enter any liquid into power outlets, extension cords or any holes in the housing of the device. If you suppose that also a minimal amount of liquid may have entered the device, it must immediately be disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced insulation can cause mortal electrical shock.

There must never be any objects entering into the device. This is especially valid for metal parts. If any metal parts like staples or coarse metal chips enter into the device, the device must be taken out of operation and disconnected immediately. Malfunction or short-circuits caused by metal parts may cause mortal injuries. The device and all connections have to be lightning protected.

Never install the powered mixer next to highly sensitive devices like pre- amplifiers or tape-decks, as the strong magnetic field of the integrated amplifier can produce hum in these devices. The magnetic field is strongest directly above or below the power mixer.

Only connect the device when the power switch is off. Never connect the inputs or outputs to any power source (batteries, etc.) Never connect output to output. Before the device is switched on all volume controls have to be set to zero or minimum position.

CAUTION: Turn the amplifier on last and off first!

Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified persons are not subject to warranty.

Keep away children and amateurs!

HEALTH HAZARD!
By operating an amplifying system, you can produce excessive sound pressure levels that may lead to permanent hearing loss.

There are no serviceable parts inside the device. Maintenance and service operations are only to be carried out by authorized dealers.

OPERATING DETERMINATIONS

This device is a professional mixing console for mixing different audio signals. This product is allowed to be operated with an alternating current of 115/230 V, 50/60 Hz and was designed for indoor use only.

This device is designed for mobile use and for permanent installations.

By operating amplifying systems, you can produce excessive sound pressure levels that may lead to permanent hearing loss. Please refer to the explanations under “Legal instructions”.

Please note: operating an amplification system in public or industrial areas, a series of safety instructions have to be followed that this manual can only give in part. The operator must therefore inform himself on the current safety instructions and consider them.
Do not shake the device. Avoid brute force when installing or operating the device.

When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture or dust. There should not be any cables lying around. You endanger your own and the safety of others!

This device must never be operated or stockpiled in surroundings where splash water, rain, moisture or fog may harm the device. Moisture or very high humidity can reduce the insulation and lead to mortal electrical shocks. When using smoke machines, make sure that the device is never exposed to the direct smoke jet and is installed in a distance of 0.5 meters between smoke machine and device.

The ambient temperature must always be between -5° C and +45° C. Keep away from direct insulation (particularly in cars) and heaters.

The relative humidity must not exceed 50 % with an ambient temperature of 45° C.

This device must only be operated in an altitude between -20 and 2000 m over NN.

The ambient contamination must never exceed level 1 and must not be conducting, only dry.

Never use the device during thunderstorms. Over voltage could destroy the device. Always disconnect the device during thunderstorms.

Operate the device only after having familiarized with its functions. Do not permit operation by persons not qualified for operating the device. Most damages are the result of unprofessional operation!
Never use solvents or aggressive detergents in order to clean the device! Rather use a soft and damp cloth.
Please use the original packaging if the device is to be transported.
Never remove the serial barcode from the device as this would make the guarantee void.

Please consider that unauthorized modifications on the speaker-system are forbidden due to safety reasons!

If this device will be operated in any way different to the one described in this manual, the product may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, hearing loss etc.

DESCRIPTION

8-channel audio mixer
The OMNITRONIC MZD-88 is an audio mixer with matrix system of 8 input and 8 outputs which allows for multiple output configurations and inputs mixing. The 8 outputs are divided in 4 groups. Thus it’s possible to supply 4 different PA zones with a stereo output by routing different input signals to these zones without having to change the cable configuration. It’s also possible to obtain 8 outputs with different mixing as every input has its own level and PAN controls.

• Matrix input assignment: 8 audio inputs are freely assignable to each of the 8 outputs
• Division of the 8 outputs into 4 groups; each with separate level and pan control per channel
• Ultra flexible configuration modes; distributes the signal of up to 8 audio sources to e.g. 8 mono zones or 4 stereo zones, each with a different output signal
• Inputs and outputs via balanced XLR jacks
• Frequency range 20-20,000 Hz
• 19″ dimensions for rack installation, 2 U

The MZD-88 is designed for professional application. The connectors are located on the rear panel, the operating elements are on the front panel. The unit features four PA zones with eight identical channels each.

• Power on/off
  Press this button, to turn the MZD-88 on and off.

• POWER LED
  The power indicator lights up when the MZD-88 is powered on.

• LEVEL control
  For adjusting the input level at the respective stereo output at the rear panel. Turn the control clockwise beyond the detente position to increase the level up to 12 dB.

• PAN control
  Positions the input signal between the left and right output of the respective zone. In mid-position, the signal level is equal at both outputs.

• Voltage selector
  Make sure this switch is properly set.

• AC input with fuse holder
  Used to plug the supplied power cord in. Only replace the fuse when the device is disconnected from mains. Only

• Inputs
  XLR inputs (bal.) for connecting audio units units with line level outputs.

• Zone outputs
  Each zone disposes of a stereo output (2 x XLR, bal.) for left and right. The PAN control directs the signal to the respective output.
  outputs STEREO A for PA zone 1,
  outputs STEREO B for PA zone 2,
  outputs STEREO C for PA zone 3,
  outputs STEREO D for PA zone 4

• A PAN control
  Positions the input signal between the left and right output of the respective zone.

• Voltage selector
  Make sure this switch is properly set.

• AC input with fuse holder
  Used to plug the supplied power cord in. The correct fuse value is specified on the rear panel.

INSTALLATION

This device is built for 19″ racks (483 mm). This rack should be a double-door rack where you can open the front panel and the rear panel. The rack should be provided with a cooling fan. When mounting the device into the rack, please make sure that there is enough space around the device so that the heated air can be passed on. Steady overheating will damage your device. You can fix the device with four screws M6 in the rack. If several devices are to be installed, make sure that you leave 1 unit space between the devices.

CONNECTIONS

All connections have to be made or changed only if the mixer and all audio devices connected to it is/are switched off!

1. Connect the outputs of the audio sources to the input jacks.
2. A PA amplifier for speakers, mixers or a subsequent unit with line level can be connected to the XLR connectors OUTPUT.

Connection with the mains

Connect the device to the mains with the enclosed power supply cable.

The occupation of the connection cables is as follows:

**** The earth has to be connected!

If the device will be directly connected with the local power supply network, a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.

The device must only be connected with an electric installation carried out in compliance with the IEC standards. The electric installation must be equipped with a Residual Current Device (RCD) with a maximum fault current of 30 mA.

OPERATION

1. Prior to switching on, set all LEVEL controls to mid-position to avoid damage to the hearing by a volume which is too high when switching on.
2. Switch on the device via the power switch. The power indicator on the front panel lights up. Switch on the connected units; always switch on your PA amplifier last.
3. Adjust the desired volume ratio with the Level controls.
4. Determine the balance of the input signal between the left and right output.
5. Switch off the unit with the POWER switch after operation.

The figure shows the signal of CH 1 routed to each pair of stereo outputs. To add signal from the CH 2 input to the STEREO A outputs, use the level controls in the same zone (STEREO A / OUT 1-2) in the second row CH 2.

Create stereo mixes with the LEVEL and PAN controls on the front panel of the MZD-88. Each row on the front panel (e.g. CH 1) corresponds to one input. Each zone on the front panel (e.g. STEREO A / OUT 1-2) corresponds to a pair of stereo outputs. Use the the LEVEL control to add signal to each pair of stereo outputs. Use the PAN control to balance the signal between the left and right output.

Application examples

The MZD-88 extends the capabilities of a standard mixing console by providing eight additional auxiliary sends, use it to create stereo or mono mixes for a variety of applications, e.g. for personal and loudspeaker monitoring, multitrack recording and monitoring, stereo effect sends, zone mixing and matrix mixing.

Monitoring
The MZD-88 gives you the possibility to create personal mixes for vocalists or instrumentalists for live and studio applications without having to reconfigure the existing setup of a mixing console.

Mixing consoles often do not provide enough dedicated outputs for monitoring applications. Even if each performer has its own speaker cabinet, he does not get his own mix. With the MZD-88 you can provide those individual mixes for each band member, regardless how different each mix needs to be.

Multitrack monitoring
Use the MZD-88‘s input connectors to insert it between the eight outputs of a multitrack recorder or a soundcard and the line inputs of another mixing console.
You can mix the outputs to four individual stereo cue mixes without interrupting the signal flow to the mixing console.

Multitrack recording
You can also insert the MZD-88 into the insert paths of a mixing console.

CLEANING AND MAINTENANCE

DANGER TO LIFE!

Disconnect from mains before starting maintenance operation!

We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use alcohol or solvents!

There are no serviceable parts inside the device except for the fuse. Maintenance and service operations are only to be carried out by authorized dealers.

Replacing the fuse

If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.

Before replacing the fuse, unplug mains lead.

Procedure:

Step 1: Open the fuse holder on the rear panel with a fitting screwdriver.
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing.

Should you need any spare parts, please use genuine parts.
If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply cable available at your dealer.
Should you have further questions, please contact your dealer.

TECHNICAL SPECIFICATIONS

Please note: Every information is subject to change without prior notice. 14.07.2011 ©

CUSTOMER SUPPORT

Das neueste Update dieser Bedienungsanleitung finden Sie im Internet unter:
You can find the latest update of this user manual in the Internet under:
www.omnitronic.com

References

• Omnitronic: Your manufacturer and wholesaler of audio equipment
• Omnitronic: Your manufacturer and wholesaler of audio equipment
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>