TF-SL7004 Taurus Iso Low Row Sterling Instruction Manual

: June 16, 2024
: taurus

TF-SL7004 Taurus Iso Low Row Sterling

Product Information

Specifications

Maximum Weight Capacity: 150 kg
Assembly Time: Approximately 120 minutes
Product Dimensions: L 176cm | W 145cm | H 165cm
Art. No.: TF-SL7004 TF-TFSL7004.01.01

About This Product

The Taurus Iso Low Row Sterling is a fitness equipment designed
for home use, semi-professional use, and commercial or professional
use. It is suitable for institutional facilities such as hospitals,
schools, hotels, associations, and fitness studios.

Disclaimer

Please note that the product and manual are subject to change.
Technical data may be changed without advance notice.

About This Manual

This manual provides important information for the installation
and safe use of the Taurus Iso Low Row Sterling. It is essential to
read the entire manual before installation and first use. Ensure
that all individuals using the equipment, especially children and
those with physical, sensory, mental, or motor disabilities, are
familiar with the manual and its contents. The manual may be
updated due to ongoing changes and software optimizations. In case
of any discrepancies, refer to the manual uploaded to the webshop
for the latest version.

The Taurus Iso Low Row Sterling has been manufactured with the
latest safety knowledge to eliminate potential safety hazards. It
is crucial to follow the instructions carefully and ensure that all
parts are securely in place. Pay close attention to the safety and
maintenance instructions provided in this manual. The contract
partner cannot be held liable for any damage to health, accidents,
or damage to the equipment resulting from non-compliance with these
instructions.

The following safety instructions may appear in this manual:

ATTENTION: This notice indicates potentially
hazardous situations which, if not avoided, may result in property
damage.
CAUTION: This notice indicates potentially
hazardous situations which, if not avoided, may result in slight or
minor injuries!
WARNING: This notice indicates potentially
hazardous situations which, if not avoided, may result in death or
serious injuries!
DANGER: This notice indicates potentially
hazardous situations which, if not avoided, will result in death or
serious injuries!

General Information

Technical Data

The technical data for the Taurus Iso Low Row Sterling are as
follows:

Maximum Weight Capacity: 150 kg
Assembly Time: Approximately 120 minutes
Product Dimensions: L 176cm | W 145cm | H 165cm

Personal Safety

When using the Taurus Iso Low Row Sterling, personal safety is
of utmost importance. Ensure that you follow these guidelines:

Read and understand the entire manual before using the
equipment.
Inform all individuals exercising with the equipment about the
manual and its contents.
Supervise the use of the equipment, especially for children and
individuals with disabilities.
Check for any updates to the manual on the webshop and refer to
the latest version if necessary.

Set-Up Place

Choose an appropriate set-up place for the Taurus Iso Low Row
Sterling:

Ensure there is enough space to assemble and use the
equipment.
Place the equipment on a flat and stable surface.
Avoid placing the equipment near obstacles or in crowded
areas.

Assembly

General Instructions

Before starting the assembly process, make sure to read through
the entire manual and understand all the instructions. Take note of
the following general instructions:

Follow the assembly steps in the given order.
Use the provided tools and accessories for assembly.
Do not use excessive force when tightening screws or
bolts.
If unsure about any step, refer to the manual or contact
customer support.

Scope of Delivery

The package for the Taurus Iso Low Row Sterling should include
the following items:

[List of items]

Assembly Process

Follow these steps to assemble the Taurus Iso Low Row
Sterling:

[Step-by-step assembly instructions]

Storage and Transport

General Instructions

When storing or transporting the Taurus Iso Low Row Sterling,
follow these guidelines:

[Storage and transport instructions]

Transportation Wheels

The equipment may be equipped with transportation wheels for
easier movement. Follow these steps to use the transportation
wheels:

[Instructions for using transportation wheels]

Troubleshooting, Care, and Maintenance

General Instructions

For troubleshooting, care, and maintenance of the Taurus Iso Low
Row Sterling, keep the following in mind:

[General instructions for troubleshooting, care, and
maintenance]

Faults and Fault Diagnosis

If you encounter any faults or issues with the equipment, refer
to the following guide for fault diagnosis:

[List of common faults and their diagnosis]

Maintenance and Inspection Calendar

Regular maintenance and inspections are necessary to ensure the
optimal performance and longevity of the Taurus Iso Low Row
Sterling. Follow the maintenance and inspection calendar provided
in the manual.

Disposal

When disposing of the Taurus Iso Low Row Sterling, follow the
proper disposal guidelines in your area. Dispose of the equipment
in an environmentally friendly manner.

Recommended Accessories

Enhance your workout experience with these recommended
accessories for the Taurus Iso Low Row Sterling:

[List of recommended accessories]

Ordering Spare Parts

Serial Number and Model Name

When ordering spare parts for the Taurus Iso Low Row Sterling,
provide the serial number and model name of your equipment.

Parts List

The parts list for the Taurus Iso Low Row Sterling is available
in the manual. Refer to it when ordering spare parts.

Exploded Drawing

An exploded drawing of the Taurus Iso Low Row Sterling is
available in the manual. Use it as a reference when ordering spare
parts.

Warranty

The Taurus Iso Low Row Sterling comes with a warranty. Refer to
the warranty terms and conditions provided in the manual for more
information.

Contact

If you have any questions or need assistance with the Taurus Iso
Low Row Sterling, contact our customer support.

Further Information

For additional information, visit our website: www.taurus- fitness.com.

FAQ

[Frequently Asked Questions]

Assembly and Operating Instructions

max. 150 kg
~ 120 Min.
168 kg L 176 | W 145 | H 165

C M

Art. No. TF-SL7004 TF-

TFSL7004.01.01
Taurus Iso Low Row Sterling

2

Low Row

Content

1 GENERAL INFORMATION

7

1.1 Technical Data

7

1.2 Personal Safety

8

1.3 Set-Up Place

9

2 ASSEMBLY

10

2.1 General Instructions

10

2.2 Scope of Delivery

10

2.3 Assembly

13

3 STORAGE AND TRANSPORT

23

3.1 General Instructions

23

3.2 Transportation Wheels

23

4 TROUBLESHOOTING, CARE AND MAINTENANCE

24

4.1 General Instructions

24

4.2 Faults and Fault Diagnosis

24

4.3 Maintenance and Inspection Calendar

25

5 DISPOSAL

25

6 RECOMMENDED ACCESSORIES

26

7 ORDERING SPARE PARTS

27

7.1 Serial Number and Model Name

27

7.2 Parts List

28

7.3 Exploded Drawing

31

8 WARRANTY

32

9 CONTACT

34

3

4

Low Row

Dear customer, Thank you for choosing quality training equipment from the TAURUS brand. Taurus offers sports and fitness equipment for home users with high demands on quality, functionality and longevity. Also, Taurus is a well- known and experienced brand for equipping professional rooms for fitness studios and business customers. The focus of Taurus fitness equipment is on what matters most in sports: maximum performance! Therefore, the devices are developed in close consultation with athletes and sports scientists. Because athletes know best what makes perfect fitness equipment.
Further information can be found at www.taurus-fitness.com.
Intended Use The equipment may only be used for its intended purpose.
This fitness equipment is suitable for home use, semi-professional use and commercial or professional use. The semi-professional sector includes, for example, institutional facilities such as hospitals, schools, hotels and associations. Professional use refers to commercial use, e.g. in a fitness studio.

Disclaimer

©2011 Taurus® is a registered brand of the company Sport-Tiedje GmbH. All rights reserved. Any use of this trademark without the explicit written permission of SportTiedje is prohibited.
Product and manual are subject to change. Technical data can be changed without advance notice.

5

ABOUT THIS MANUAL
Please carefully read the entire manual before installation and first use. The manual will help you to quickly set up the system and explains how to safely use it. Make sure that all persons exercising with the equipment (especially children and persons with physical, sensory, mental or motor disabilities) are informed about this manual and its contents in advance. In case of doubt, responsible persons must supervise the use of the equipment.
Due to ongoing changes and software optimisations, the manual may have to be updated. If you notice any discrepancies during assembly or use, please refer to the manual uploaded to the webshop. The latest manual is always available there.
This equipment has been manufactured according to the latest safety knowledge. As far as possible, potential safety hazards which could cause injury have been eliminated. Make sure to carefully follow
the instructions and that all parts are securely in place. If required, read through the instructions again to correct any mistakes.
Please pay close attention to the safety and maintenance instructions given here. The contract partner cannot be held liable for damage to health, accidents or damage to the equipment when it is not used in accordance with these instructions.
The following safety instructions may appear in this manual:
ATTENTION This notice indicates potentially hazardous situations which, if not avoided, may result in property damage.
CAUTION This notice indicates potentially hazardous situations which, if not avoided, may result in slight or minor injuries!
WARNING This notice indicates potentially hazardous situations which, if not avoided, may result in death or serious injuries!
DANGER This notice indicates potentially hazardous situations which, if not avoided, will result in death or serious injuries!
NOTICE This notice indicates further useful information.
Retain these instructions in a safe place for future reference, maintenance or when ordering replacement parts.

6

Low Row

1 GENERAL INFORMATION

1.1 Technical Data

Weight and Dimensions

Packaging dimensions (L x W x H) and article weight (gross, incl. packaging) approx.:

Box 1: Box 2:

201.5 cm x 72.5 cm x 32.5 cm 108.5 cm x 76.5 cm x 43.5 cm

122 kg 73.6 kg

Set-up dimensions (L x W x H) approx.:

176 cm x 145 cm x 165 cm

Article weight (net, excl. packaging) approx.:

167.5 kg

Maximum user weight: Maximum load weight (training): Maximum load weight (storage):

150 kg 2 x 150 kg 2 x 100 kg

Class:

S

NOTICE This equipment is compatible with weight plates with a 50 mm hole and a maximum external diameter of 500 mm (not included in the scope of delivery).

7

1.2 Personal Safety
DANGER + Before you start using the equipment, you should consult your physician that this type of exercise is suitable for you from a health perspective. Particularly affected are persons who: have a hereditary disposition to high blood pressure or heart disease, are over the age of 45, smoke, have high cholesterol values, are overweight and/or have not exercised regularly in the past year. If you are under medical treatment that affects your heart rate, medical advice is absolutely essential. + Note that excessive training can seriously endanger your health. Please also note that heart rate monitoring systems can be inaccurate. If you notice any signs of weakness, nausea, dizziness, pain, shortness of breath, or other abnormal symptoms, stop exercising immediately and seek advice from your doctor if necessary. + The owner must communicate all warnings and instructions to the user.
WARNING + This equipment may not be used by children under the age of 14. + Children should not be allowed unsupervised access to the equipment. + Persons with disabilities must have a medical license and must be under strict observation when using the equipment. + The equipment is strictly for use by one person at a time. + If your equipment provides a safety key, the clip of the safety key must be attached to your clothing before starting your training. In the event of a fall, the EMERGENCY STOP of the equipment can be initiated. + Keep your hands, feet and other body parts, hair, clothing, jewellery and other objects well clear of moving parts. + During use, wear suitable sports clothing rather than loose or baggy clothing. When wearing sports shoes, make sure they have suitable soles, preferably made of rubber or other nonslip materials. Shoes with heels, leather soles, studs or spikes are unsuitable. Never exercise barefoot. + Always start each workout with a light warm-up and end with a cool-down phase. + Using the machine as a support during stretching exercises or attaching resistance bands, ropes or other accessories to it, may cause injuries.
CAUTION + If your equipment needs to be connected to the power supply with a mains cable, make sure that the cable is not a potential tripping hazard. + Make sure that nobody is within the range of motion of the equipment during training so as not to endanger you or other persons. + Be aware that if adjustment devices are left protruding, they may impede the user’s movement.
ATTENTION + Do not insert any objects of any kind into the openings of the device.

8

Low Row

1.3 Set-Up Place
WARNING + Do not place the equipment in main corridors or escape routes.
CAUTION + Choose a location in which to place the equipment such that there is enough free space/ clearance to the front, the rear and to the sides of the equipment. + The training room should be well ventilated during training and not be exposed to any draughts. + Choose the place in which to set up the equipment such that there is enough free space/ clearance to the front, the rear and to the sides of the equipment. + The free area in the direction from which the exercise equipment is accessed must be at least 0.6 m larger than the exercise area. + The set-up and mounting surface of the equipment should be flat, loadable and solid. + If your device is to be mounted on the wall/ceiling, make sure that you use the appropriate assembly material to avoid possible damages or personal injuries. The contractual partner accepts no liability for this. ATTENTION + The device may only be used in one building, in sufficiently tempered and dry rooms (ambient temperatures between 10°C and 35°C). The equipment should not be used outdoors or in rooms with high humidity (over 70%) like swimming pools. + A floor protective mat/equipment underlay can help to protect high-quality floor coverings (parquet, laminate, cork, carpets) from dents and sweat and can help to level out slight unevenness. + For Class S and I equipment, the exercise equipment may only be used in areas where access, supervision and control are specifically regulated by the owner.
9

2 ASSEMBLY
2.1 General Instructions
DANGER + Do not leave any tools, packaging materials such as foils or small parts lying around, as otherwise there is a danger of suffocation for children. Keep children away from the equipment during assembly.
WARNING + Pay attention to the instructions attached to the equipment in order to reduce the risk of injuries.
CAUTION + Ensure to have sufficient room for movement in each direction during assembly. + The assembly of the equipment must be carried out by at least two adults. If in doubt, seek the help of a third technically skilled person.
ATTENTION + To prevent damage to the equipment and the floor, assemble the equipment on a mat or
packaging board.
NOTICE + In order to make the assembly as simple as possible, some screws and nuts to be used can already be pre-assembled. + Ideally, assemble the equipment at its later set-up place.
2.2 Scope of Delivery
The scope of delivery consist of the following parts. At the beginning, check whether all parts and tools belonging to the device are included in the scope of delivery and whether damage has occurred. In the event of complaints, the contractual partner must be contacted directly.
CAUTION If parts of the scope of delivery are missing or damaged, the assembly must not be carried out.

10

Low Row

Content of Box 1

Part no. Description

Qty.

1

Left Bottom Frame

1

2

Right Bottom Frame

1

3

Upright Frame

2

4

Weight Horn Assembly

2

9

Middle Standing Frame

1

13

Pivot Plate 1

2

14

Pivot Plate 2

2

11

Content of Box 2

Part no. Description

Qty.

5

Left Arm Frame

1

6

Right Arm Frame

1

7

Long Cross Frame

1

8

Short Cross Frame

1

15

Seat Frame

1

16

Chest Pad

1

17

Seat Pad

1

21

Pivot Shaft

2

29

Pull Spring

1

30

Idler Wheel

2

Manual

1

Hardware Pack

3

12

Manual Hardware pack
Low Row

2.3 Assembly
Before assembly, take a close look at the individual assembly steps shown and carry out the assembly in the order given.
NOTICE + First loosely screw all parts together and check that they fit properly. Tighten the screws using the tool only when you are instructed to do so. + If you have difficulty recognising the graphics, we recommend that you open and/or download the PDF instructions stored in the webshop on your end device (e.g. smartphone, tablet or PC). There you have the option of zooming in closer.

Required Tools

Ratchet Wrench and Socket Adjustable Wrench Rubber Mallet Hex Key Wrench Set Phillips Screwdriver

13

Step 1: Assembly of the Bottom Frames and Cross Frames
NOTICE Do not tighten the screws and nuts completely yet.
Attach the long cross frame (7) and the short cross frame (8) to the left and right bottom frames (1 & 2) with a total of eight screws (49), 16 flat washers (62) and eight lock nuts (65).

14

Low Row

Step 2: Assembly of the Upright Frames and Middle Standing Frame NOTICE
Do not tighten the screws and nuts completely yet. 1. Attach one upright frame (3) to the left bottom frame (1) with four screws (52) and four flat
washers (62). 2. Attach another upright frame (3) to the right bottom frame (2) with four screws (52) and four
flat washers (62). 3. Attach the middle standing frame (9) to the long cross frame (7) with two screws (52) and two
flat washers (62). 4. Attach the middle standing frame (9) to the upright frames (3) with a total of two narrow outside
plates (12), four screws (49), eight flat washers (62) and four lock nuts (62). 5. Tighten the screws and nuts from this and the previous assembly step with the appropriate
tools.
15

Step 3: Assembly of the Arm Frames
1. Slide one pivot shaft (21) through the right arm frame (6). 2. Attach two baffle rings (83), one pivot plate 1 (13) and one pivot plate 2 (14) to the right arm
frame (6) with two domed aluminium caps (23) and two screws (54). 3. Attach the right arm frame (6) to the right sided upright frame (3) with three screws (47), six flat
washers (62) and three lock nuts (65). 4. Repeat the steps 1 to 3 with the left arm frame (5). 5. Tighten the screws and nuts with the appropriate tools.

16

Low Row

Step 4: Assembly of the Weight Horns and Weight Plate Storages 1. Attach two weight plate storages (11) to the right upright frame (3) with a total of four screws
(50), eight flat washers (62) and four lock nuts (65). NOTICE
The weight horns should be installed at a 5-degree-angle like shown. 2. Attach one weight horn (4) to the right arm frame (6) with one screw (53) and one domed
aluminium cap (23). 3. Secure the weight horn (4) with two screws (82), two spring washers (81) and two flat washers
(80). 4. Slide one rubber bumper (22) onto the weight horn (4). 5. Repeat the steps 1 to 4 on the left side. 6. Tighten the screws and nuts with the appropriate tools.
17

Step 5: Assembly of the Seat Frame
NOTICE + Do not tighten the screws and nuts completely yet. + Make sure that the seat frame (15) can be moved up and down smoothly. If needed, slightly loosen the screws and nuts.
1. Attach the seat frame (15) to the middle standing frame (9) with two idler wheels (30), two screws (48), four flat washers (62) and two lock nuts (65).
2. Slide the supporting sleeve (71) between the two frame parts of the seat frame (15). 3. Attach the supporting sleeve (71) to the seat frame (15) with one screw (55), two flat washers
(63) and one lock nut (64).
CAUTION Carefully hold the pull spring (29) at the hooks.
4. Hook the pull spring (29) onto the supporting sleeve (71) and the middle standing frame (9).

18

Low Row

Screw

Pull spring

Flat washer Supporting sleeve

Seat frame

Flat washer Lock nut

19

Step 6: Assembly of the Pads
1. Attach the seat pad (17) to the seat frame (16) with two screws (57) and two flat washers (63). 2. Attach the chest pad (16) to the middle standing frame (9) with two screws (56) and two flat
washers (63). 3. Tighten the screws with the appropriate tool. 4. Check that all screws and nuts are properly tightened and retighten if needed.
The assembly is completed.

63 56
63
57

20

Low Row

Load and Unload Weight Plates
CAUTION + Make sure to always use some sort of weight collar when exercising with external weights. + Never store unused weight plates on the floor. + Store unused weight plates on a weight rack or on the integrated storage options.
ATTENTION + The weight horn is compatible with 50 mm weight plates with a maximum external
diameter of 450 mm. + Weight plates and weight collars are not included in the scope of delivery. + Do not load more than 150 kg on each weight horn (training). + Do not load more than 100 kg on each weight horn (storage).
1. To load the weight horn, carefully grab one weight plate at a time with both hands.
2. Slide each weight plate onto the weight horn one by one until you have reached your desired training weight.
3. Attach a weight collar to secure the weight plates from sliding off.
4. To unload the weight horn, take off the weight collar.
5. Slide each weight plate off of the weight horn with both hands one by one.

Weight plates

Weight horn for training
Weight horn for storage

21

Seat Adjustment

Seat

1. Push the adjustable handle. 2. Move the seat to the desired position. 3. Release the handle.

Exercise Instructions

Adjustable handle

1. Select an appropriate weight. 2. Adjust the seat to the desired position. 3. Sit on the seat with your chest resting against the chest pad. 4. Grasp the handles. 5. Slowly pull the handles towards your chest. 6. Pause slightly at the end position. 7. Slowly return to the starting position.

Starting position

End position

22

Low Row

3 STORAGE AND TRANSPORT 3.1 General Instructions
WARNING + The storage location should be chosen so that improper use by third parties or children can be prevented. + If your equipment does not have transportation wheels, the equipment must be disassembled before transportation. ATTENTION + Make sure that the equipment is protected from moisture, dust and dirt in the selected storage location. The storage location should be dry and well ventilated and have a constant ambient temperature between 10°C and 35°C.
23

4 TROUBLESHOOTING, CARE AND MAINTENANCE

4.1 General Instructions
WARNING + Do not make any improper changes to the equipment.
CAUTION + Damaged or worn components may affect your safety and the life of the equipment. Safety can only be guaranteed if you check the equipment regularly for wear and damage. Replace damaged or worn components immediately. In such a case, contact the contract partner. The equipment must not be used until it has been repaired. If necessary, use only original spare parts.
ATTENTION + In addition to the instructions and recommendations for maintenance and care given here,
additional service and/or repair work may be necessary; this must only be carried out by authorised service technicians.
4.2 Faults and Fault Diagnosis
The equipment undergoes regular quality controls during production. Nevertheless, faults or malfunctions may occur. Frequently, individual parts are responsible for these disturbances, an exchange is usually sufficient. Please refer to the following overview for the most common errors and how to correct them. If the equipment still does not function properly, contact your contract partner.

Fault Squeaking & cracking noises
Unit wobbles

Cause

Solution

Screw connections loosened + Check or lubricate

or too tight

connections*

+ Uneven ground

+ Align unit

+ Loose screw connections + Tighten screw connections

With a grease-free silicone oil or silicone spray.

screw

24

Low Row

4.3 Maintenance and Inspection Calendar
To avoid damage from body sweat, the equipment must be cleaned with a damp towel (no solvents!) after each training session.
The following routine tasks must be performed at the specified intervals:

Part Screw connections Cushions Legend: C = clean; I = inspect

Weekly C

Monthly I

Quarterly

5 DISPOSAL
At the end of its operational life, this equipment cannot be disposed of in normal household waste. Instead, it must be disposed of via an recycling centre. Further information can be obtained from your local authority`s recycling service.
The materials can be recycled as per their symbols. Through the reuse, recycling of materials or other forms of recovery of old equipment, you make an important contribution to the protection of the environment.
25

6 RECOMMENDED ACCESSORIES
To make your training experience even more efficient and pleasant, we recommend that you add suiting accessories to your fitness equipment. For training equipment like smith machines, weight benches or racks this could for example be a floor mat, which makes your fitness equipment stand more securely and also protects the floor from sweat but it could be also additional weights, handles, foot straps for leg exercises or triceps ropes. For some smith machines, there are also optional addons such as leg presses that make your workout even more intense and comprehensive.
Our range of accessories offers the highest quality and makes training even better. If you would like to find out more about compatible accessories, please go to the detail page of the product in our webshop (the easiest way is to enter the article number in the search field above) and go to the recommended accessories on this page. Alternatively, you can use the QR code provided. Of course, you can also contact our customer service: by telephone, e-mail, in one of our branches or via our social media channels. We will be happy to advise you!

floor mat

chest strap

weight block extension

triceps rope

26

Low Row

7 ORDERING SPARE PARTS 7.1 Serial Number and Model Name
In order to provide you with the best possible service, please have the model name, article number, serial number, exploded drawing and parts list ready. The corresponding contact options can be found in chapter 9 of this operating manual. NOTICE
The serial number of your equipment is unique. It’s located on a white sticker. The exact position of this sticker is shown in the following illustration. Enter the serial number in the appropriate field.
Serial number:
Brand / Category: Taurus / multi gym
Model Name: Iso Low Row Sterling
Article Number: TF-SL7004 27

7.2 Parts List

No. Supplier parts no.

Name

Specifi cation

Qty.

1

SL70040100

Left Bottom Frame

1

2

SL70040200

Right Bottom Frame

1

3

SL70040300

(left/right) Upright Frame

2

4

SL70041000V1

Weight Horn Assembly

2

5

SL70040500

Left Arm Frame

1

6

SL70040600

Right Arm Frame

1

7

SL70040700V1

Long Cross Frame

1

8

SL70040800

Short Cross Frame

1

9

SL70040900

Middle Standing Frame

1

10 SL70012800

Adjustable Handle

1

11 SL70100300

Weight Plate Storage

4

12 SL70010103

Narrow Outside Plate

452006

2

13 SL70041300

Pivot Plate 1

151.4244.610

2

14 SL70041400

Pivot Plate 2

151.4244.610

2

15 SL70012300

Seat Frame

441.91176

1

16 SL70041600V1

Chest Pad

20030070

1

17 SL70013000V1

Seat Pad

34027070

1

18 SL7007B2100

Pedal

25010525*2

2

19 SL70011100

Front Plastic Plate

43510719

1

20 SL70011200

Rear Plastic Plate

43510719

1

21 SL70011500

Pivot Shaft 30

30*134

2

22 SL70013100

Rubber bumper

DT764225

2

23 SL70011700

Domed Aluminium Cap 5412.510.6

6

24 SL70011800

Long Weight Horn Sleeve 41.449361

2

25 SL70100400

Weight Horn Sleeve

41.449223

4

26 SL70012000

Weight Horn Plastic Cap 4912.525

2

27 SL70042700

Short Aluminium Grip

3125150

2

28 SL70012100

Aluminium Grip

3125.4175

2

29 SL70012200

Pull Spring

31.52.5165

1

30 SL70012400

Idler Wheel

6040113.5

3

31 SL70012500

Wheel Shaft

1712.5116.5

3

28

Low Row

32 SL70012600

Wring Spring

30330

1

33 SL70012700

Shaft For Adjustable

12*135.1

1

Handle

34 PL380800

Large Rubber Bumper

12014052

2

35 SL70013200

Plastic Sleeve

181019

2

36 HF985A1500

Weight Horn Rubber

764225

4

Donut

37 IT90102100

Aluminium Cap 25

4310.526

1

38 IT90102200

Aluminium Ring 25

4026.818

1

39 RF-6012500

End Plug

41.3*34

4

40 CG50001700

Rubber Grip

DT191470

1

41 CWRVL0051200

Rubber Foot

159.5159.511

4

42 M01402000

Oilite Bushing

2512.213

2

43 GB2766203-2Z

Ball Bearing

6203-2Z

6

44 GB894.117FH12

External Retaining Ring 17

6

12

45 GB894.112FH12

External Retaining Ring 12

2

17

46 GB2766206-2ZC3

Ball Bearing 6206-2Z

6206-2Z

4

47 GB70M12*155DHS20

Socket Head Cap Screw M12155(8.8 degree) 6 M12155

48 GB70M12*145DHS20

Socket Head Cap Screw M12145(8.8 degree) 2 M12145

49 GB70M12*135DHS20

Socket Head Cap Screw M12135(8.8 degree) 12 M12135

50 GB70M12*125DHS20

Socket Head Cap Screw M12125(8.8 degree) 8 M12125

51 GB70M12*90DHS20

Socket Head Cap Screw M12*90

4

M12*90

52 GB70M123535DHS20NL Socket Head Cap Screw M12*35(full thread,8.8 2

M12*35

degree)

53 CNLM125050DS20NL Flat Head Cap Screw M12*50

M12*50(full thread, ,8.8 2 degree)

54 CNLM12*30DS20NL

Flat Head Cap Screw M12*30

M12*30( ,8.8 degree) 4

55 GB70M10*145DHS20

Socket Head Cap Screw M10145(8.8 degree) 1 M10145

29

56 PNLM10*75DHS2

Button Head Cap Screw M10*75

2

M10*75

57 PNLM10*30DHS2

Button Head Cap Screw M10*30

2

M10*30

58 CNLM10*25DS20NL

Flat Head Cap Screw M10*25

M10*25(8.8 degree) 1

59 PNLM8*65DHS2

Button Head Cap Screw M8*65

2

M8*65

61 YZGB7710-32*3.2N19

Socket Set Screw 10-

10-32UNF*3.2

2

32*3.2

62 DQ12DHS2A

Flat Washer 13241.5 13241.5

8

63 GB9510DHS2

Flat Washer 11202 11202

6

64 NM10DHS2

Nylon lock Nut M10

M10

1

65 NM12DHS2

Nylon lock Nut M12

M12

4

66 NM8DHS2

Nylon lock Nut M8

M8

2

67 NBS10DHS

Hex key S=10

S=10

1

68 NBS8DHS

Hex key S=8

S=8

1

69 NBS6DHS

Hex key S=6

S=6

1

70 NBS4DHS

Hex key S=4

S=4(Long

1

side=120mm)

71 SL70026700

Supporting Sleeve

162.0117

1

72 GB17880.3M8*16.5DS17 Rivet Nut M8

M8

4

73 CNLM8*20DS2

Flat Head Cap Screw

M8*20

4

M8*20

80 GB958DHS2

Flat Washer 9161.6 9161.6

4

81 GB938DHS12

Spring Washer 8

8

4

82 GB70M8*30DHS20

Socket Head Cap Screw M8*30(8.8 degree)

4

M8*30

83 SL70022500

Baffle Ring

4630.53

4

30

Low Row

7.3 Exploded Drawing
31

8 WARRANTY
Training equipment from Taurus® is subject to strict quality control. However, if a fitness equipment purchased from us does not work perfectly, we take it very seriously and ask you to contact our customer service as indicated. We are happy to help you by phone via our service hotline.
Error Descriptions Your fitness equipment is developed for long-term, high- quality training. However, should a problem arise, please first read the operating instructions. For further assistance, please contact your contract partner or call our service hotline. To ensure your problem is solved as quickly as possible, please describe the defect as exactly as possible.
In addition to the statutory warranty, we provide a warranty for every fitness equipment purchased from us according to the following provisions.
Your statutory rights are not a ected.
Warrantee The warrantee is the first/original buyer and/or any person who received a newly purchased product as a gift from the original buyer.
Warranty period The warranty periods, shown on our web shop, begin on delivery of the fitness equipment. The
respective warranty periods for your equipment can be found on its product website.
Repair Costs According to our choice, there will either be a repair, a replacement of individual damaged parts or a complete replacement. Spare parts, that have to be mounted while assembling the equipment, have to be replaced by the warrantee personally and are not a part of repair. After the expiration of the warranty period, the responsibility for parts costs, repair costs, installation costs and delivery costs lies with the warranty holder.
The terms of use are defined as follows: + Home use: solely for private use in private households up to 3 hours per day + Semi-professional use: up to 6 hours per day (e. g. rehabilitation centres, hotels, clubs, company gyms) + Professional use: more than 6 hours per day (e. g. commercial gyms)
Warranty Service Within the warranty period, equipment which develops faults as a result of material or manufacturing defects, will be repaired or replaced at our discretion. Ownership of equipment or parts of equipment which have been replaced is transferred to us. The warranty period is not extended nor does a new warranty period begin following repair or replacement under the warranty.

32

Low Row

Warranty Conditions For the warranty to be valid, the following steps must be taken:
Please contact our customer service by email or phone. If the product under warranty has to be sent in for repair, the seller bears costs. After expiry of the warranty, the buyer bears the costs of transport and insurance. If the fault is covered by our warranty, you will receive a new or repaired equipment in return.
Warranty claims are invalid in case of damage resulting from: + misuse or improper handling + environmental influences (moisture, heat, electrical surge, dust, etc.) + failure to follow the current safety measures for the equipment + failure to follow the operating instructions + use of force (e. g. hitting, kicking, falling) + interventions which were not carried out by one of our authorized service centres + unauthorised repair attempts
Proof of Purchase and Serial Number Please make sure that you are able to provide the appropriate receipt when claiming on your warranty. So that we can clearly identify the model of your equipment, and for the purposes of our quality control, you will need to give the serial number of your equipment, when contacting the service team. Where possible please have your serial number and your customer number ready when you call our service hotline. It will help us to deal with your request swiftly.
If you cannot find the serial number on your fitness equipment, our service team is at your disposal to offer further information.
Service outside of the Warranty Period We are also happy to issue an individual cost estimate if there is a problem with your fitness equipment after the warranty has expired, or in cases which do not fall under the terms of the warranty, e. g. normal wear and tear. Please contact our customer service team to find a quick and cost-effective solution to your problem. In such a case you will be responsible for the delivery costs.
Communication Many problems can be solved just by speaking to us as your specialist supplier. We know how important it is to you as a user of the fitness equipment to have problems solved quickly and simply, so you can enjoy working out with minimal interruption. For that reason, we also want to resolve your queries quickly and in a straightforward manner. Thus, please always keep your customer number and the serial number of the faulty equipment handy.
33

9 CONTACT

DE
TECHNIK
+49 4621 4210-900 +49 4621 4210-698 technik@sport-tiedje.de Öffnungszeiten entnehmen Sie
unserer Homepage.
SERVICE
0800 20 20277
(kostenlos)
04621 4210 – 0 info@sport-tiedje.de Öffnungszeiten entnehmen Sie
unserer Homepage.
UK
CUSTOMER SUPPORT
00800 2020 2772
+494621 4210 944
info@sport-tiedje.co.uk You can find the opening hours
on our homepage.

DK
TEKNIK OG SERVICE
80 90 16 50
+49 4621 4210-945
info@fitshop.dk Åbningstider kan findes på
hjemmesiden.
PL
DZIAL TECHNICZNY I SERWIS
22 307 43 21
+49 4621 42 10-948
info@fitshop.pl Godziny otwarcia mona
znale na stronie glównej.
NL
TECHNISCHE DIENST & SERVICE
+31 172 619961 service@fitshop.nl De openingstijden vindt u op
onze homepage.

FR
TECHNIQUE & SERVICE
+33 (0) 189 530984
+49 4621 42 10 933
info@fitshop.fr Vous trouverez les heures
d’ouverture sur notre site Internet.
BE
TECHNIQUE & SERVICE
02 732 46 77
+49 4621 4210 933
info@fitshop.be Vous trouverez les heures
d’ouverture sur notre site Internet.
INT
TECHNICAL SUPPORT & SERVICE
+49 4621 4210-944 service-int@sport-tiedje.de You can find the opening
hours on our homepage.

ES
TECNOLOGÍA Y SERVICIOS
911 238 029 info@fitshop.es Consulta nuestro horario de
apertura en la página web.

AT
TECHNIK & SERVICE
0800 20 20277 (Freecall)
+49 4621 42 10-0
info@sport-tiedje.at Öffnungszeiten entnehmen
Sie unserer Homepage.

CH
TECHNIK & SERVICE
0800 202 027
+49 4621 42 10-0
info@fitshop.ch Öffnungszeiten entnehmen
Sie unserer Homepage.

Please find a detailed overview including address and opening hours for all stores of the Sport-Tiedje Group in Germany and abroad on the following website:
www.sport-tiedje.com/en/stores

34

Low Row

WE
LIVE
FITNESS
WEBSHOP AND SOCIAL MEDIA
Sport-Tiedje is Europe’s largest specialist store for home fitness equipment with currently over 70 stores and one of the world’s most renowned online mail order companies for fitness equipment. Private customers order via the 25 web shops in the respective national language or have their desired equpiment assembled on site. In addition, the company supplies fitness studios, hotels, sports clubs, companies and physio practices with professional equipment for endurance and strength training. Sport-Tiedje offers a wide range of fitness equipment from renowned manufacturers, high-quality in-house developments and comprehensive services, such as a build-up service and sports scientific advice before and after the purchase. The company employs numerous sports scientists, fitness trainers and competitive athletes.
Visit us also on our social media platforms or our blog!

www.sport-tiedje.co.uk www.sport-tiedje.de/blog www.facebook.com/SportTiedje
www.instagram.com/sporttiedje
www.youtube.com/user/sporttiedje

35

Notes

36

Low Row

Notes
37

Notes

38

Low Row

39

Taurus Iso Low Row Sterling