GGQF V311B Battery Tester User Manual
- June 16, 2024
- GGQF
Table of Contents
GGQF V311B Battery Tester
Safety measures and warning
Safety precautions and warnings to prevent personal injury or damage to the
vehicle and / or battery tester.
When working on the vehicle, first observe this instruction manual and at
least observe the following safety precautions. Failure to follow the
instructions in this manual may damage the instrument. This product is
designed and manufactured in strict accordance with IEC / EN61010-1 safety
standard.
- Detection shall be carried out in safe environment.
- Keep clothing, hair, hands, tools and test equipment away from all motor heating parts.
- Lead compounds and chemical substances are contained in the terminals, terminals and related accessories of the battery. Before measuring the data, the insulation layer of the clamp shall be checked and shall not be exposed or disconnected.
- V311B Suitable for 12V automobile starting battery, working voltage is DC9 ~ 18V, please do not check the series battery. The voltage value will be higher than that when the battery is fully charged under normal conditions. Turn on the headlamp for 2-3 minutes, and then check the battery after the voltage drops to the normal value. Do not use or store products in high temperature, high humidity, inflammable, explosive and explosive environment.
Product description
Tool description
① LCD display – Display the detection result.
② ③ ④ ⑤ ⑥ ⑦
Back button, OK button, scroll up button, scroll left button, scroll right
button, scroll down button
⑧ Battery test connector – connect the product to the battery end of the
vehicle
Specification description
Display: 240 320 pixel display
Operating Temperature: -20 to 60℃
Storage Temperature:- 20 to 70℃
External Power: 12V
Size :15688*24mm
Support Language: English, Chinese, Portuguese, Italian, French, German,
Spanish, polish, Russian
Battery test
There are two test modes for battery capacity test, standard test and fast test For battery test, connect the red clip to the positive pole of the battery and the black clip to the negative pole of the battery. The equipment will automatically supply power and prepare for the test.
If you test the battery in the vehicle, do not insert the key or keep it in
the of position. Ensure all electrical equipment and door closing equipment
are working.
Enter the battery test interface and select test mode
Select the standard test mode, enter the interface, select the battery type,
and press the OK button to continue:
Press the OK button to select the mode and select the correct battery model:
Press the “OK” button to continue to input the rated current CCA:500 CCA Use
the up and down key to enter the correct CCA value.
Press the “OK” button to continue to display the test result information.
Battery
Volt| 12.25V
Rated| 370CCA
Measured| 492CCA
Resistance| 6.30mΩ
Life（SOH）| 100.0%
State of charge| 64%
Great
Start test
Select the start test interface, press the Enter key to enter the test
interface, and turn on the key to start the engine at the same time, and
display the waveform diagram of the minimum and maximum voltage values of the
test results
Charging test
Select the recharge test interface and press the enter button to enter the
test interface.
According to the requirements, turn on the headlamp for about 3 seconds, then
turn it of, and keep the engine speed above 2500
Press the OK button to enter the test interface.
Charge
- Please turn the headlights on for 3 seconds and the off
- Keep engine speed above 2500 rpm for 3 seconds, then press “OK” to rest
After starting the test, wait about 2 seconds to display the test result information
Charge
Load Voltage| 12.22V
No-load voltage| 12.29V
Ripple| 0.08V
Charge voltage| Low
Battery waveform display, display the minimum and maximum voltage value, can
be synchronized monitoring and battery waveform analysis.
Setup
Enter the settings, select the information to be set and enter the interface information
| Setting | 1/5 |
|---|
language
Buzzer switch
Screen capture
Self test
About
Enter the language setting interface and select the required language according to the up and down buttons
| Language | 1/9 |
|---|---|
| English |
1/2>
Enter the buzzer selection interface and press the enter button to select whether to “on” or “off”
Buzzer switch
| Buzzer switch | 1/2 |
|---|
ON
OFF
Screen capture setting
To enter the screen capture interface, it must be a combination of up and down buttons. Press the key to add or cancel, and press the confirm key to save the picture information;
Screen capture
Press the button to add or cancel,and press “OK” to save It has to be a combination of two keys
Tool self test
Press the OK button to enter the tool self-test interface, screen display and key test.
| Self test | 1/2 |
|---|
LCD test
Key test
About
Display product software and hardware version information
About
SW: V20.0
HW : V10.0
Note: the printing function must be under the condition that the product
has saved the screen capture picture Connect the product type-C interface with
the computer, the computer will automatically install the driver, enter the
printing interface, select the picture, press the OK button to enter the
printing, select the picture information on the computer to complete the
printing.
Information
- Keep printing this interface
- A removable disk will appear when connected to the computer via a USB cable
- Copy pictures from the picture folder to your computer for printing
Disclaimer Conditions
We are committed to providing unparalleled customer support to our customers
before and after sales. Below we over our exemption for this product:
If any of the following conditions are met, the customer shall not enjoy the
benefits covered by this limited warranty:
a) Products due to abnormal use, abnormal conditions and inappropriate
storage (such as exposure to front and back or overlap, should be authorized
to modify, misuse, negligence, repetition, accident, modification, incorrect
installation or other non-faulty behavior) Damage, including damage caused by
transportation.
b) Our company is not responsible for damage to products caused by
external causes (such as collision with objects) or fire, flood, sand, dust,
storm, lightning, earthquake or weather conditions, irresistible acts of
natural disasters or leakage of batteries, theft, fuse breaking, incorrect use
of any power source.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>