Supcline S4601 TV Wall Mount User Manual

**Supcline S4601 TV Wall Mount User Manual

**

Installation Instruction

**Full Motion TV Wall Mount

** Thank you for choosing Supcline! All our products come with 10 years warranty.
As a manufacturer, we strive to provide you with the highest quality products and services. If you have any issues during installation and use, please contact us atsupcline@126.com.

We’re 24 hours available!

Warning!
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please feel free to contact our Customer Service.

• This product is designed for use in wood stud and solid concrete wall.
  • DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and mount combined.
• Do not apply this product to any purpose not indicated by Supcline.
• Incorrect installation may result in product damage or body injury.
  Supc line shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

Tools Needed (Not Included)

• Tape Measure

• Pencil

• Awl

• Screw Driver

• Electric Drill

• 1/2 in. (13mm) Socket Wrench

Wood Stud Install

• Stud  Finder

• Wood Drill Bit 7/32 in. (5.5mm)

Concrete Install

• 3/8 in. (10mm) Masonry Drill Bit

• Hammer

Contained Parts and Hardwares

Main Parts

1. velcro x3

2. Levelx1

3. cable Clamping x2

4. Extension Arm(L) X2

5. Extension Arm(R) X2

6. wall Panel x1

7. Face Panel x1

8. Face Panel Arm x2

9. Mounting Template x1

V Bracket x2

For TV Bracket Installing

a : M6x*415 x4

b :  M6*35 x4

c : M8*15 x4 **

d : M825 x4

e : M835 x4

f :* M850 x4

g : M6/M8 Washer (4168.51.5) x4

h : 5mm Spacer Ring (¢188.55.0) x8

i : 110mm Spacer Ring (¢188.510.0) x8

For Wall Drilling

A : Anchor (10*50) × 6

B : Tapping Screw (M7*55)×6

C : M8 Washer (228.52.0)×6

D : M6*12 X8

Step 1: Before Installation

Check the wall

Drywall with wood studs

Solid concrete or concrete block
CAUTION:
DO NOT install into pure drywall alone

Check your TV VESA pattern (Vesa=Horizontal x Vertical) Measure the four holes at the back of your TV.
Max.: 600mm( 23.62″)
Min.: 200mm(7.87″)

Please check the ports on the back of the TV to avoid potential clogging.

Step 2: Assemble the Brackets

1. Select the right screws/washers/spacer rings according to the size and depth of the TV screw holes.

2. Figure out the suitable screw combination according to your TV
   Combination of screws and washers . . . . . .. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . .. . . .. . . .. . .. . Combination of screws, washers and spacer rings

3. Attach the brackets

Step 3A: For Wood Stud Installation

3A-1 Assemble extension arms option
When wood studs spacing < 16″, do not need extension arms;
When 16″ < wood studs spacing < 24″, assemble the extension arms first.

Attach to wood studs

plan A: without extension arms
| plan B: with extension arms

---|---

• Use a stud finder (not included) to locate wood studs. Mark the edge and center locations of the stud.
• Position the mounting template at desired height and align the holes with the stud center line.

Level the template and mark the holes.

• Drill four pilot holes.

• Mount the wall panel using four sets of B tapping screws and C washers.

CAUTION: To avoid potential personal injury or property damage: All 4 tapping screws B MUST BE firmly tightened to prevent unwanted movement of the wall panel. To prevent the TV falling down, the BOLT HEAD must keep UP at this step!!

Step 3B: For Concrete/Brick Wall Installation

• Position the mounting template at desired height, level it and mark the pilot holes.

• Drill pilot holes. Make sure the depth is not less than 2.5″ Do not drill in the gap where two bricks join.

• Make sure the anchors are inserted straight into the wall.

• Mount the wall panel using four sets of B tapping screws and C washers.

Step 4: Hang the TV onto the Wall Panel

1. Verify the firmness of the wall panel

2. Face panel arms assembly
   Tighten the screws

   • Remove the four screws on face panel 7, and install the two face panel arms @, then tighten the four screws on both sides.

3. Connect face panel with wall panel

4. Hang up and adjust the TV

Step 5: Adjustments

1. Tilt (+12°/-5°)
   Adjust the TV at your preferred angle and tighten the tilt bolts.

2. Horizontal adjustment +3°
   Loosen the 2 bolts on the back of your TV and tighten them after finished adjustment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>