LG I24CGH Air Conditioner Owner’s Manual

AIR CONDITIONER
OWNER’S MANUAL

I24CGH Air Conditioner

Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.
TYPE: WALL MOUNTED

www.lg.com
Copyright © 2023 LG Electronics Inc. All Rights Reserved

This manual may contain images or content different from the model you purchased.
This manual is subject to revision by the manufacturer.

SAFETY INSTRUCTIONS

The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect operation of the appliance.
The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described below.

**** This symbol is displayed to indicate matters and operations that can cause risk. Read the part with this symbol carefully and follow the instructions in order to avoid risk.

WARNING
This indicates that the failure to follow the instructions can cause serious injury or death.
CAUTION
This indicates that the failure to follow the instructions can cause the minor injury or damage to the product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING
To reduce the risk of explosion, fire, death, electric shock, injury or scalding to persons when using this product, follow basic precautions, including the following:

Children in the Household
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Installation

• Do not install the air conditioner on an unstable surface or in a place where there is danger of it falling.
• Contact an authorized service center when installing or relocating the air conditioner.
• Install the panel and the cover of the control box safely.
• Do not install the air conditioner in a place where flammable liquids or gases such as gasoline, propane, paint thinner, etc., are stored.
• Make sure that the pipe and the power cable connecting the indoor and outdoor units are not pulled too tight when installing the air conditioner.
• Use standard circuit breaker and fuse that conform to the rating of the air conditioner.
• Do not input air or gas into the system except with the specific refrigerant.
• Use non-flammable gas (nitrogen) to check for leak and to purge air; using compressed air or flammable gas may cause fire or explosion.
• The indoor/outdoor wiring connections must be secured tightly, and the cable should be routed properly so that there is no force pulling the cable from the connection terminals. Improper or loose connections can cause heat generation or fire.
• Install dedicated electric outlet and circuit breaker before using the air conditioner.
• Do not connect the ground wire to a gas pipe, a lightning rod, or a telephone ground wire.
• Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
• Do not install the unit in potentially explosive atmospheres.

Operation

• Be sure to use only those parts listed in the service parts list. Never attempt to modify the equipment.
• Make sure that children do not climb on or hit the outdoor unit.
• Dispose of the batteries in a place where there is no danger of fire.
• Use only the refrigerant specified on the air conditioner label.
• Cut off the power supply if there is any noise, smell, or smoke coming from the air conditioner.
• Do not leave flammable substances such as gasoline, benzene, or thinner near the air conditioner.
• Contact an authorized service center when the air conditioner is submerged by flood waters.
• Do not use the air conditioner for an extended period of time in a small place without proper ventilation.
• In the event of a gas leak (such as Freon, propane gas, LP gas, etc.) ventilate sufficiently before using the air conditioner again.
• Be sure to ventilate sufficiently when the air conditioner and a heating appliance such as a heater are used simultaneously.
• Do not block the inlet or outlet of air flow.
• Do not insert hands or other objects through the air inlet or outlet while the air conditioner is operating.
• Make sure that the power cable is neither dirty, loose, nor broken.
• Never touch, operate, or repair the air conditioner with wet hands.
• Do not place any objects on the power cable.
• Do not place a heater or other heating appliances near the power cable.
• Do not modify or extend the power cable. Scratches or peeling insulation on the power cables may result in fire or electric shock, and should be replaced.
• Cut off the power supply immediately in the event of a blackout or a thunderstorm.
• Take care to ensure that power cable could not be pulled out or damaged during operation.
• Do not touch refrigerant pipe, water pipe and any internal parts while the unit is operating or immediately after operation.

Maintenance

• Do not clean the appliance by spraying water directly onto the product.
• Before cleaning or performing maintenance, disconnect the power supply and wait until the fan stops.

Technical Safety

• Installation or repairs made by unauthorized persons can pose hazards to you and others.
• The information contained in the manual is intended for use by a qualified service technician who is familiar with the safety procedures and equipped with the proper tools and test instruments.
• Failure to read and follow all instructions in this manual can result in equipment malfunction, property damage, personal injury and/or death.
• The appliance shall be installed in accordance with national wiring regulations.
• When the power cord is to be replaced, the replacement work shall be performed by authorized personnel using only genuine replacement parts.
• This appliance must be properly grounded to minimize risk of electric shock.
• Do not cut or remove the grounding prong from the power plug.
• Attaching the earth wire to the power outlet cover screw does not ground the appliance unless the cover screw is metal, uninsulated, and the power outlet is grounded through house wiring.
• If you have any doubt whether the air conditioner is properly grounded, have the power outlet and circuit checked by a qualified electrician.
• The refrigerant and insulation blowing gas used in the appliance require special disposal procedures. Consult a service agent or a similarly qualified person before disposing of them.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.

CAUTION
To reduce the risk of minor injury to persons, malfunction, or damage to the product or property when using this product, follow basic precautions, including the following:

Installation

• Do not install the air conditioner in an area where it is directly exposed to sea wind (salt spray).
• Install the drain hose properly for the smooth drainage of water condensation.
• Exercise caution when unpacking or installing the air conditioner.
• Do not touch the leaking refrigerant during installation or repair.
• Transport the air conditioner with two or more people or use a forklift.
• Install the outdoor unit such that it is protected from direct sunlight. Do not place the indoor unit in a place where it is directly exposed to sunlight via the windows.
• Safely dispose of packing materials such as screws, nails, plastic bag or batteries using proper packaging after installation or repair.
• Install the air conditioner in a place where the noise from the outdoor unit or the exhaust fumes will not inconvenience the neighbors. Failure to do so may result in conflict with the neighbors.

Operation

• Remove the batteries if the remote control is not to be used for an extended period of time.
• Make sure that the filter is installed before operating the air conditioner.
• Be sure to check if there is a refrigerant leak after installing or repairing the air conditioner.
• Do not place any object on the air conditioner.
• Never mix different types of batteries, or old and new batteries for the remote control.
• Do not let the air conditioner run for a long time when humidity is very high or when a door or a window has been left open.
• Stop using the remote control if there is a fluid leak in the battery. If your clothes or skin are exposed to the leaking battery fluid, wash off with clean water.
• Do not expose people, animals, or plants to the cold or hot wind from the air conditioner for extended periods of time.
• If the leaking battery fluid has been swallowed, rinse the inside of the mouth thoroughly and consult a doctor.
• Do not drink the water drained from the air conditioner.
• Do not use the product for special purposes, such as preserving foods, works of art, and etc. It is an air conditioner for consumer purposes, not a precision refrigeration system. There is risk of damage or loss of property.
• Do not recharge or disassemble the batteries.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Maintenance

• Never touch the metal parts of the air conditioner when removing the air filter.
• Use a sturdy stool or ladder when cleaning, maintaining, or repairing the air conditioner at a height.
• Never use strong cleaning agents or solvents when cleaning the air conditioner or spray water. Use a smooth cloth.
• To clean the interior, contact an authorized service center or dealer. Using harsh detergents may cause corrosion or damage to the unit.

NAMES OF PARTS

Indoor Unit

1. Front panelFront panel
2. Air filterAir filter
3. Optional filter (if installed)
4. LED DisplayLED Display
5. Signal receiverSignal receiver
6. Terminal block cover| 7. Ionizer generator (if installed)
8. Deflectors
9. Emergency button
10. Indoor unit rating label
11. Airflow direction louver
12. Remote controller
---|---

Outdoor Unit

13. Air outlet grille
14. Outdoor unit rating label
15. Terminal block cover
16. Gas valve
17. Liquid valve

NOTE

• The above figures are only intended to be a simple diagram of the appliance and may not correspond to the appearance of the units that have been purchased.

INDOOR UNIT DISPLAY

Display

NOTE

• The shape and position of switches and indicators may be different according to the model, but their function is the same.

EMERGENCY FUNCTION

Emergency Function
If the remote controller fails to work or maintenance necessary, proceed as follows:
Open and lift the front panel up to an angleto reach the emergency button.

1. One press of the emergency button (one beep) will lead to the forced COOLING operation.
2. Two press of the emergency button within 3 seconds (two beeps) will lead to the forced HEATING operation.
3. To switch off the unit, you just need to press the button again (a single long beep).
4. In forced operation, the air conditioner will automatically start working in 23 °C cooling/ Heating mode, auto fan speed.

1. Front panel
2. Emergency button

WARNING

• The shape and position of the emergency button may be different according to the model, but their function is the same.

NOTE

• The external static pressure of heat pumps is 0 Pa for all models.
• The emergency button in some models could be on the right part of the unit under the front panel.

REMOTE CONTROLLER

Using Wireless Remote Control
You can operate the air conditioner more conveniently with the remote control.

(20 °C ~ 28 °C)
Swing| | To adjust the air flow direction vertically.
Swing| | To adjust the air flow direction horizontally. (Optional)
Room Temp.| | To display the room temperature.
Sleep| | To set the sleeping mode automatically.
Func.| | The Ion generator uses millions of ions to help improve indoor air quality. (Optional)
| To remove moisture generated inside the indoor unit.
Timer| | To turn on/off air conditioner automatically at desired time.
Set/ Cancel| –| To set/cancel the special functions and timer.
| –| To adjust time.
°C/°F (5 s)| | To change unit between °C and °F

Replacement of Batteries
When: There is no confirmation beep heard from the indoor unit. The LCD doesn’t act.
Remove the battery cover plate from the rear of the remote controller, by sliding it in the direction of the arrow.
Install the batteries according the direction (+ and-) shown on the Remote Controller.
Reinstall the battery cover by sliding it into place.

WARNING

• Use 2 LR03 AAA (1.5V) batteries. Do not use rechargeable batteries. Replace the old batteries with new ones of the same type when the display is no longer legible.
• Do not dispose batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

NOTE

• Please remove batteries to avoid leakage damage when not using for a long time.

NOTE

• Direct the remote controller toward the air conditioner.
• Check that there are no objects between the remote control and the signal receptor in the indoor unit.
• Never leave the remote controller exposed to the rays of the sun.
• Keep the remote controller at a distance of at least 1 m from the television or other electrical appliances.

1. Signal receptorSignal receptor

OPERATING INSTRUCTIONS

Cooling Mode
The cooling function allows the air conditioner to cool the room and at the same time reduces air humidity.
To activate the Cooling mode of operation, press the Mode button on the remote controller until the symbol appears on the display.
The cooling function is activated by setting the button or at a temperature lower than that of the room.
To optimize the function of the air conditioner, adjust the temperature 1 , the speed 2. and the direction of the air flow 3. by pressing the buttons indicated.

NOTE

• For cooling mode, the minimum adjusted temperature by control unit is preferred to be more than 20 °C

Auto Mode (auto changeover / auto operation mode)

In Auto mode, the air conditioner will run automatically according to the room temperature.
To activate the Auto mode of operation, press the Mode button on the remote controller until the symbol appears on the display.
To optimize the function of the air conditioner, adjust the temperature 1 , the speed 2 and the direction of the air flow 3 by pressing the buttons indicated.

Dry Mode
This function reduces the humidity of the air to make the room more comfortable.
To activate the Dry mode of operation, press the Mode button on the remote controller until the symbol appears in the display.
An automatic function of alternating cooling cycles and air fan is activated.

Heating Mode
The heating function allows the air conditioner to heat the room.
To activate the Heating mode of operation, press the Mode button on the remote controller until the symbol appears on the display.
With the button or set a temperature higher than that of the room.
To optimize the function of the air conditioner, adjust the temperature 1 , the speed 2 and the direction of the air flow 3 by pressing the buttons indicated.

NOTE

• For heating mode, the maximum adjusted temperature by control unit is preferred to be less than 28 °C

Fan Mode
The air conditioner works in only ventilation.
To activate the Fan mode of operation, press the Mode button on the remote controller until the symbol appears in the display.
To optimize the function of the air conditioner, Adjust the speed 1 and the direction of the air flow 2  By pressing the buttons indicated.

Fan Speed
Adjusting the Fan Speed

• Press Fan Speed button repeatedly to adjust the fan speed.

Fan speed indicator

Light Off
Switch on/off the LED display on panel.
To turn off the panel display, press Light Off button.
To turn on the panel display again, press Light Off button.
If the indoor display is set to OFF, pressing a button on the remote control automatically turns the display on for 15 seconds.

Jet Mode

To activate Jet Mode function, pressing the button Jet Mode or pressing the button Fan Speed until appears on the display.
To cancel this function, pressing the Fan Speed to switch other fan speed or pressing the Jet Mode button again.
In Cooling / Auto / Heating / Fan mode, when you select Jet Mode feature, it will use the highest fan setting to blow strong airflow.

Swing Control

Vertically Swing
Press the button to activate the “Vertically Swing”.

• If press time interval is in 2 seconds, the swing will cycle as below:
• If long press the button, the swing angle range will cycle as below:

Horizontally Swing
Press the button to activate the “Horizontally Swing”.

• If press time interval is in 2 seconds, the swing will cycle as below:
• If long press the button, the swing angle range will cycle as below:

NOTE

• Adjusting the air flow direction horizontally may not be supported, depending on the model.
• Adjusting the air deflector arbitrarily may cause product failure.
• Never position manually, the delicate mechanism might seriously damaged! (Models without Horizontally Swing can adjust manually.)
• Never poke fingers, sticks or other objects in the air inlet or outlet vents. Such accidental contact might cause unforeseeable damage or hurt.
• Adjusting the swing angle change may not be supported, depending on the model.

Energy Saving
In this mode the appliance automatically sets the operation to achieve energy savings.

1. Turn on the appliance and select a Cooling, Heating mode.
2. Press the “Energy Saving” button, the appliance will run in Energy Saving mode.
3. Pressing the “Energy Saving” button again will cancel the mode, symbol will no longer be shown on the LCD screen.

In Energy Saving mode, the temperature 1 , the speed 2 and the direction of the air flow 3 can be adjusted by pressing the buttons indicated.

Dual Sensing
Press the “Dual Sensing” button, the appliance will run in Dual Sensing mode.
Pressing the “Dual Sensing” button again will cancel the mode, symbol will no longer be shown on the LCD screen.
This function enable the remote control to measure the temperature at its current location and send this signal 7 times in 2 hours to the air conditioner to enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
It will automatically deactivate 2 hours later.
In Dual sensing mode, the temperature 1 , the speed 2 and the direction of the air flow 3 can be adjusted by pressing the buttons indicated.
Advice to put the remote controller in the place where the indoor unit receive signal easily.

Room Temp
Room temperature is displayed about 5 seconds if you press Room Temp. button.

Change Celsius to
Fahrenheit °C~°F
Press Room Temp. button for 5 seconds.

• Repeat the same process to change again.

Setting the Current Time

1. Insert batteries (reinsert a battery if already inserted/or use the reset button).
   • The icon below blinks at the bottom of the display screen.

2. Press or button to select the time.

3. Press Set/Cancel button to finish.

NOTE

• The On/Off Timer is available after setting the current time.

Setting the On/Off Timer
This function sets the air conditioner to turn on/off automatically at desired time.

Setting the On Timer

1. Press button.
   • The icon below blinks at the bottom of the display screen.

2. Press or button to select the minutes.
   Press Set/Cancel button to finish.

3. After setting the timer, current time and icon are displayed on the display screen indicating that the desired time is set.

Canceling the On Timer

1. Press button.
   • The icon below blinks at the bottom of the display screen.

2. Press Set/Cancel button to finish.

Setting the Off Timer

1. Press button.
   • The icon below blinks at the bottom of the display screen.

2. Press or button to select the minutes.

3. Press Set/Cancel button to finish.
   • After setting the timer, current time and icon are displayed on the display screen indicating that the desired time is set.

Canceling the Off Timer

1. Press button.
   • The icon below blinks at the bottom of the display screen.

2. Press Set/Cancel button to finish.

NOTE

• On/Off Timer can not be set together.
• On Timer is available when the product is turned off.
• Off Timer is available when the product is turned on.

Using the Sleep Function

1. Turn the appliance on.

2. Press Sleep button.
   • The icon below blinks at the bottom of the display screen.

3. Do it again to deactivate this function.
   • is displayed on the display screen.

NOTE

• After 10 hours running in sleep mode, the air conditioner will return to the previous setting mode.

Using Special Function

1. Turn the appliance on.
2. Press button repeatedly to select the desired function.
3. Press Set/Cancel button to finish.
4. Do it again to deactivate this function.

Auto Clean
In the Cooling and Dehumidification Mode, moisture is generated inside the indoor unit. This function removes such moisture.
This function enable the air conditioner still blow airflow about 15 minutes to dry the indoor inner parts to avoid mildew, when the air conditioner is off.

Air Purification (Optional)
These functions supply clean and fresh air by ion particles and the filter.

NOTE

• Some functions may not be supported, depending on the model.
• Some functions may operate differently from the remote control display.

PROTECTION

The air conditioner is programmed for comfortable and suitable living conditions, if it is used in abnormal conditioner as below, certain safety protection features might come into effect.

Fix air conditioner:

WARNING

• The unit does not operate immediately if it is turned on after being turned off or after changing the mode during operation. This is a normal self-protection action, you need wait for about 3 minutes.
• The capacity and efficiency are according to the test conducted at full-load operation.
• The highest speed of indoor fan motor and the maximum open angle of the flaps and deflectors are requested.

AUTO-RESTART FUNCTION

Auto-Restart Function
The appliance is preset auto-restart function by manufacturer. In case of a sudden power failure, the module memorizes the setting conditions before the power failure. When the power restores, the unit restarts automatically with all the previous settings preserved by the memory function.

MAINTENANCE

Periodic maintenance is essential for keeping your air conditioner efficient.
Before carrying out any maintenance, disconnect the power supply by taking the plug out from the socket.

Air Filters

1. Open the front panel following the direction of the arrow.
2. Keeping the front panel raised with one hand, take out the air filter with the other hand. 1. Air filterAir filter
3. Clean the filter with water; if the filter is soiled with oil, it can be washed with warm water (not exceeding 45 °C). Leave to dry in a cool and dry place.
4. Keeping the front panel raised with one hand, insert the air filter with the other hand.
5. Close.

Cleaning the Heat Exchanger

1. Open the front panel of the unit and life it till its greatest stroke and then unhooking it from the hinges to make the cleaning easier.
2. Clean the indoor unit using a cloth with the water (not higher than 40 °C) and neutral soap. Never use aggressive solvents or detergents.
3. If the outdoor unit is clogged, remove the leaves and the waste and remove the dust with air jet or a bit of water.

End of Season Maintenance

1. Disconnect the automatic switch or the plug.
2. Clean and replace the filters.
3. On a sunny day let the conditioner work in ventilation for some hours, so that the inside of the unit can dry completely.

TROUBLESHOOTING

Please check the following before you contact the service center. If the problem persists, contact your local service center.

Damaged indoor/outdoor unit fan motor.
Faulty compressor thermomagnetic circuit breaker.
Faulty protective device or fuses.
Loose connections or plug pulled out.
It sometimes stops operating to protect the appliance.
Voltage higher or lower than the voltage range.
Active TIMER-ON function.
Damaged electronic control board.
Strange odour.| Air filter dirty.
Noise of running water.| Back flow of liquid in the refrigerant circulation.
A fine mist comes from the air outlet.| This occurs when the air in the room becomes very cold, for example in the “COOLING” or “DRY” modes.
A strange noise can be heard.| This noise is made by the expansion or contraction of the front panel due to variations in temperature and does not indicate a problem.
Insufficient airflow, either hot or cold.| Inappropriate temperature setting.
Air inlet or outlet of indoor or outdoor unit has been blocked.
Air filter is blocked.
Fan speed set at minimum.
Other sources of heat in the room.
No refrigerant.
The appliance does not respond to commands.| Remote control is not near enough to indoor unit.
Battery in remote controller may have been exhausted.
Obstacles between remote control and signal receiver in indoor unit.
The display is off.| Press “Light Off” button.
Power failure.

WARNING

• Switch off the air conditioner immediately and cut off the power supply in the event of:
  − Strange noises during operation.
  − Faulty electronic control board.
  − Faulty fuses or switches.
  − Spraying water or objects inside the appliance.
  − Overheated cables or plugs.
  − Very strong smells coming from the appliance.

Error Signals on the Display
In case of error, the display on the indoor unit shown the following error codes:

| RUN lamp| Description of the trouble
---|---|---
| Flashes once| The fault of indoor temperature sensor.
| Flashes twice| The fault of indoor pipe temperature sensor.
| Flashes 6 times| Malfunction of indoor fan motor.
| Display code| Refrigerant leakage.

After Sales Service (Egypt Only)
Shelf Life Time: 7 Years
LG is committed to providing all spare parts of this appliance during the shelf life time.

Guidelines for Electrical Energy Saving

This manual shall include instructions for Electrical Energy saving related to operating air conditioner by the customer as follows:

• Select the temperature which is adjusted for cooling or heating mode to be energy saving so that room temperature is at a comfortable level.

In summer
Don’t wait until the room is too hot. Turn the room air conditioner for cooling before that.
Avoid exaggeration in adjusting the temperature so that the room is very cold in the case of cooling mode because it leads to increased consumption of electrical energy as it is harmful to health.

In winter
Don’t wait until the room is too cold, Turn the air conditioner for heating before that.
Avoid exaggeration in adjusting the temperature so that the room is very hot in the case of heating mode because it leads to increased consumption of electrical energy as it is harmful to health.

• Doors, windows and any other openings shall be closed inside the conditioned room to prevent leakage of the conditioned air outside and to prevent the non-conditioned air from entering the conditioned room to maintain the air conditioner efficiency.
• Make sure that the conditioned room is not exposed to direct sunlight. In case of exposure to sunlight, set down the curtains on windows to prevent exposure to sunlight and to maintain the efficiency of the air conditioner.
• Make sure that there is no obstructing to the movement of the air conditioned out of the air conditioner or the movement of return air to the device in order to maintain the efficiency of the device and the amount of air necessary for it, so take into account the absence of curtains, furniture or any obstructions in front of your air conditioner.
• Use the healthy economic function during the sleeping time to save electrical consumption and get comfortably healthy sleep while running the air conditioner for cooling or heating.
• Ensure the regularity of the air distribution in the place to be conditioned by the correct choice for the prompt movement of the air conditioned router by the operating system cooling or heating by:
  − Using automatic Swing function for horizontal movement router to the air conditioned.
  − Using Control the movement of horizontal movement router to the air conditioned.
  − Manual adjustment of the vertical routers to the air conditioned to the left or right as needed.
  − Instruction manual for installation and maintenance of the air-conditioner.

References

• LG Electronics & Home Appliances | Shop Now | LG USA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>