BOSCH Atino Line Laser Level with Measuring Tape Instruction Manual

: June 16, 2024
: Bosch

Table of Contents

BOSCH Atino Line Laser Level with Measuring Tape
Safety Instructions
Product Description and Specifications
Technical data
Assembly
- Attaching the Measuring Tool
Operation
- Starting Operation
- Working Advice
Maintenance and Service
Disposal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BOSCH Atino Line Laser Level with Measuring Tape

BOSCH-Atino-Line-Laser-Level-with-Measuring-Tape-
PRODUCT

Robert Bosch Power Tools GmbH 70538 Stuttgart

GERMANY

www.bosch-pt.com
1 609 92A 8LY (2023.03) T / 318

Safety Instructions

All instructions must be read and observed in order for the meas-uring tool to function safely. The safeguards integrated into the measuring tool may be compromised if the measuring tool is not used under these instructions. Never make warning signs on the measuring tool unrecognisable. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE AND INCLUDE THEM WITH THE MEASURING TOOL WHEN TRANSFERRING IT TO A THIRD PARTY.

Warning! If operating or adjustment devices other than those specified here are used or other procedures are carried out, this can lead to dangerous exposure to radiation.
The measuring tool is delivered with a laser warning sign (marked in the illustra-tion of the measuring tool on the graphics page).
If the text of the laser warning label is not in your national language, stick the provided warning label in your national language over it before operating for the first time.
Do not direct the laser beam at persons or animals and do not stare into the direct or reflected laser beam yourself. You could blind somebody, cause accidents or damage your eyes.
If laser radiation hits your eye, you must close your eyes and immediately turn your head away from the beam.
Do not make any modifications to the laser equipment.
Do not use the laser goggles (accessory) as protective goggles. The laser goggles make the laser beam easier to see; they do not protect you against laser radiation.
Do not use the laser goggles (accessory) as sunglasses or while driving. The laser goggles do not provide full UV protection and impair your ability to see colours.
Have the measuring tool serviced only by a qualified specialist using only ori-ginal replacement parts. This will ensure that the safety of the measuring tool is maintained.
Do not let children use the laser measuring tool unsupervised. They could unin-tentionally blind themselves or other persons.
Do not use the measuring tool in explosive atmospheres which contain flam-mable liquids, gases or dust. Sparks may be produced inside the measuring tool, which can ignite dust or fumes. Keep the magnet away from implants and other medical devices, e.g. pacemakers or insulin pumps. The magnet generates a field that can impair the function of implants and medical devices.
Keep the measuring tool away from magnetic storage media and magnetically sensitive devices. The effect of the magnets can lead to irreversible data loss.

Product Description and Specifications

Please observe the illustrations at the beginning of this operating manual.

Intended Use

The measuring tool is intended for determining and checking horizontal and vertical lines on vertical surfaces. On horizontal or inclined surfaces, the non-levelled laser line can be used as reference.
The measuring tool is suitable for indoor use.
This product is a consumer laser product by EN 50689.

Product Features
The numbering of the product features shown refers to the illustration of the measuring tool on the graphic page. INDESIT-BDE86436XSUKN-Washer-Dryer-
FIG-2

On/off button
Light-up ring
Laser beam outlet aperture
Battery compartment cover
Locking mechanism of the battery compartment cover
Pin pad
Pin
Magnet
Serial number
Tape measure housing
Tape measure
Laser warning label
Addition to the laser warning label
Holder for gel pad
Gel pad
Protective cap for gel pad
Locking marking
Marking aid

Technical data

INDESIT-BDE86436XSUKN-Washer-Dryer-FIG-4

depending on surface characteristics and ambient conditions
Only non-conductive deposits occur, whereby occasional temporary conductivity caused by condensation is expected. The serial number (9) on the type plate is used to clearly identify your measuring tool.

Assembly

Inserting/Changing the Battery
It is recommended that you use alkaline manganese batteries to operate the measuring tool.

Do not use lithium-ion batteries. This may result in damage to the measuring tool. To open the battery compartment cover (4), press on the locking mechanism (5) and remove the battery compartment cover. Insert the battery. When inserting the batteries, ensure that the polarity is correct according to the illustra-tion on the inside of the battery compartment. Close the battery compartment before using the measuring tool. If the battery is running low, the light-up ring (2) will flash yellow three times after the tool is switched on. The measuring tool can be operated for approx. another 15 min.
Take the battery out of the measuring tool if you do not intend to use the tool for a long time. When it is stored in the measuring tool for longer periods, the battery can corrode and discharge itself.

Attaching the Measuring Tool

Selecting/changing the pad
The measuring tool can be attached to walls or other vertical surfaces. Depending on the type of substrate, either the gel pad (15) or the pin pad (6) can be used. As a general rule: The gel pad (15) is suitable for smooth surfaces. The pin pad (6) is suitable for coarse or rough surfaces and wallpaper on drywalls. The pin pad cannot be attached to concrete (regardless of the surface). INDESIT-BDE86436XSUKN-Washer-Dryer-
FIG-6

To change the gel pad, turn the gel pad holder (14) anticlockwise and take the gel pad (15) and holder off the measuring tool. Attach the pin pad (6) and turn it clockwise as far as it will go. The same procedure should also be followed when switching from the pin pad to the gel pad.

Attaching with the gel pad Requirements
The substrate must be dry and firm. The gel pad is not guaranteed to stick to damp, particularly dusty, sharp-edged or highly textured surfaces. If attached to unsuitable surfaces such as these, the measuring tool can fall off and become damaged or damage the substrate. If the gel pad becomes dirty or does not stick to smooth surfaces any more, it must be cleaned or replaced (see “Cleaning the Gel Pad”, page 22). Before every use, select an inconspicuous area lower down on the desired surface to check whether the gel pad will stick to this substrate, and that it can be safely removed without damaging the substrate. Always remove the measuring tool once you have finished taking a measurement, or if the substrate is being worked on in some manner (e.g. drilling, screwdriving, or hammer-ing).

Positioning the measuring tool on the substrate
Turn the protective cap (16) of the gel pad anticlockwise and remove it. Remove the pro-tective film from the gel pad before using it for the first time. Gently press the measuring tool against the substrate until it is firmly affixed. Applying excessive pressure may damage the measuring tool.

Removing the measuring tool from the substrate
Push the measuring tool carefully away from the substrate. Removing the measuring tool from a delicate surface too quickly can damage the substrate. Place the protective cap (16) on the gel pad (15) so that the locking markings (17) on the protective cap and gel pad are pointing towards each other. Then turn the protective cap clockwise all the way. The measuring tool should only ever be transported and stored with the protective cap attached. If the gel pad becomes dirty, it will lose its adhesive strength.

Attaching with the Pin Pad
The substrate must be dry and firm. Insert the pins into the recesses on the pin pad. Ensure that the pins are securely affixed to the substrate. Always remove the measuring tool once you have finished taking a measurement, or if the substrate is being worked on in some manner (e.g. drilling, screwdriving, or hammer-ing).

Operation

Starting Operation

Special Safety Instructions for Operation

Protect the measuring tool from moisture and direct sunlight.
Do not expose the measuring tool to any extreme temperatures or variations in temperature. For example, do not leave it in a car for extended periods. In case of large temperature variations, allow the measuring tool to adjust to the ambient temperature before putting it into operation. The precision of the measuring tool may be compromised if exposed to extreme temperatures or variations in temperature.
Avoid substantial knocks to the measuring tool and avoid dropping it. Damaging the measuring tool can cause accuracy to be compromised. Calibrate the measuring tool after it has been dropped or subjected to heavy impact. Check the laser line by comparing it with a known horizontal or vertical reference line.

Switching On/Off
To switch on the measuring tool, briefly press the On/off button (1). The light-up ring (2) flashes green three times when the battery has sufficient capacity. The laser line lights up immediately after switching on the measuring tool.

Do not direct the laser beam at persons or animals and do not stare into the laser beam yourself (even from a distance).

To switch off the measuring tool, briefly press the on/off button (1) again.

Never leave the measuring tool unattended when switched on, and ensure the measuring tool is switched off after use. Others may be blinded by the laser beam.If no button on the measuring tool is pressed for approx. 15 minutes and the housing is not rotated, the measuring tool will automatically switch off to preserve battery life.

Levelling a Laser Line
When attaching the measuring tool vertically, the laser line can either be levelled horizontally to the right (90°) or left (270°), or vertically upwards (0°) or downwards (180°). If the measuring tool is not aligned vertically, the laser line can only be used as a non-lev-called reference line. The levelling status is indicated using the light-up ring (2):

INDESIT-BDE86436XSUKN-Washer-Dryer-FIG-7

Working Advice

Working with the Tape Measure
The zero point of the tape measure (11) is situated in the centre of the marking aid (18), it can be marked directly on the substrate.

Note: The zero point marking can be offset by up to ±1 mm compared to the laser line. Pull the tape measure housing (10) away from the measuring tool and mark additional points at the required distances at the height of the laser line. Do not pull the tape measure (11) out any further than up to the end of the imprinted scale. You can double the work area by placing the measuring tool in the middle of the work surface and measuring on two sides one after the other.The tape measure will roll itself up again automatically
Note: Do not let go of the unrolled tape measure (11). Uncontrolled retraction may damage the tape measure.

Calibrating the Laser Line
Calibration should be carried out in the following cases:

After the tool has been dropped or subjected to heavy impact
Every 6 months If necessary, check the levelling of the laser line on a known horizontal or vertical reference line. Always perform a thorough and complete calibration to avoid incorrect measuring res-ults.
Attach the measuring tool to a vertical surface.
While the measuring tool is either switched on or off, press the on/off button (1) for at least 3 s until the laser beam starts flashing and the light-up ring (2) is no longer lit.
Slowly and evenly rotate the housing of the measuring tool once by more than 360°. The rotation should take at least 15 s.
The calibration process is completed successfully once the light-up ring (2) lights up green.
If the light-up ring (2) lights up red after calibration, the calibration has failed. Restart the calibration.

Maintenance and Service

Maintenance and Cleaning

Keep the measuring tool clean at all times.
Never immerse the measuring tool in water or other liquids.
Wipe off any dirt using a damp, soft cloth. Do not use any detergents or solvents.
Only wash the gel pad when it has been detached from the tool.

Rinse the gel pad (15) with water. Wash it as necessary using a common household neutral soap or a detergent. Do not use any cleaning agents that contain alcohol or solvents. Leave the gel pad, holder and protective cap to dry completely. The gel pad must not be warmed up (e.g. through warm air or heating).

Cleaning the Gel Pad
Clean the gel pad (15) whenever it has become contaminated with dust or other particles, or if its adhesive strength has been reduced.If the adhesive strength is still not sufficient even after the gel pad (15) has been cleaned, it should be replaced.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com The Bosch product use advice team will be happy to help you with any questions about our products and their accessories. In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

You can find further service addresses at:

www.bosch-pt.com/serviceaddresses

Disposal

Measuring tools, accessories and packaging should be recycled in an environmentally friendly manner. Do not dispose of measuring tools or batteries with household waste.

Only for EU countries:
According to Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, measuring tools that are no longer usable, and, according to Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner. If disposed of incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Licenses
Copyright © 2012–2020 STMicroelectronics All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

Redistributions of source code must retain the above copyright notice, this list of con-ditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSI-NESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE

EU Declaration of Conformity

Line laser Article number

We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and conform with the following standards.

The notified body no. 0071: Laboratoire National de métrologie et dʼEssais (LNE), 1, rue Gaston Boissier, 75724 Paris Cedex 15, FRANCE, has carried out the testing under 2014/32/EU, Module D1 and issued the following certificate: no. LNE‑36144 Revision 3, dated 2022‑09‑12. Technical file at: INDESIT-
BDE86436XSUKN-Washer-Dryer-FIG-8

Declaration of Conformity

Line laser
- Atino
Article number
- 3 603 F63 A00

We declare under our sole responsibility that the stated products comply with all applicable provisions of the regulations listed below and are in conformity with the following standards. Technical file at: Robert Bosch Ltd. (PT/SOP-GB), Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom The Electromagnetic Compatibility Regulations 2016 The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 The Measuring Instruments Regulations 2016

EN 61010-1:2010+A1:2019
EN IEC 61326-1:2021
EN IEC 63000:2018

The UK Approved Body no. 8521: LNE‑GMED UK, Suite A First Floor, East Wing Focus 31, Mark Road, Hemel Hempstead, Hertfordshire, HP2 7BW, United Kingdom, certifies that the quality assurance system complies with The Measuring Instruments Regulations 2016, module D1 and issued the following certificate: No. UKCA‑38536 Revision 0, dated 2022‑11‑21. INDESIT-BDE86436XSUKN-Washer-
Dryer-FIG-9