Breezary 33004-BK Ceiling Fan with Light User Manual
- June 16, 2024
- Breezary
Table of Contents
INSTALLATION & USER MANUAL
CEILING FAN WITH LIGHT
ITEM#
33004-BK
Customer Service: support@breezary.com
Safety Information
READ AND SAVE THESE INSTRUCTIONS.
- To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
- All wiring must be in accordancce with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
- The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 Ibs (15.9 kg). Use only UL Listed outlet boxes marked “ Acceptable for Fan Support of 35 Ibs. (15.9 kg) or less. ”
- Do not place objects in the path of the blades.
- To clean the fixture ,turn off the power, wait for it to cool, and wipe the fixture with a clean dry, soft cloth.
- After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
- All screws must be checked and retightened where necessary before installation.
WARNING: To reduce the risk of electrical shock or fire, not use this fan
with any solid-state fan speed control device. It will permanently damage the
electronic circuitry.
WARNING: To reduce the risk of fire or injury do not use this product in
conjunction with any variable (rheostat) wall control.
WARNING: To reduce the risk of personal injury, do not bend the blade
brackets when installing the rackets balancing the blades, or cleaning the
fan. Do not insert objects.
WARNING: To reduce the risk of fire, electric shock or personal injury,
mount to outlet box marked “acceptable for fan support of 35 Ibs. (15.9 Kg) or
less” and use screws provided with the outlet box.
WARNING: To avoid possible electrical shock, turn the electricity off at
the main fuse box before wiring.
WARNING: To reduce the risk of electrical shock, this must be installed
with an isolating wall control / switch.
CAUTION: To reduce the risk of personal injury, use only the screws
provided with the outlet box.
CAUTION: Please use carefully when working around or cleaning the fan to
avoid injury or damage of fan.
CAUTION: The fan must be mounted with a minimum A of 7.5 feet (2.3 Meter)
clearance from the trailing edge of the blades to the floor.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
eaqgquinment.
Dimension Reference
Hardware Included
| Hardware Package | Quantity |
|---|---|
| 1.Wire Nut | 3 |
| 2. J-Box Screw | 2 |
| 3. Washer | 4 |
| 4. Self- Tapping Screw | 4 |
Buy yourself
Fan Parts Included
| Item Name | Quantity |
|---|---|
| 1.Ceiling Fan Housing | 1 |
| 2.Remote Control | 1 |
| 3.Remote Control Wall Plate | 1 |
| 4,.Remote Control Accessory Pack | 1 |
Eneray Saving Usage
- Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance.
Choosing the Appropriate Mounting Location
Ceiling fans should be installed or mounted in the middle of the room and
positioned at least 7.5feet above the floor and 18 inches away from the walls.
If the ceiling height allows, it is recommended to install the fan 7.5~9 feet
above the floor to achieve optimal airflow.
Turn Off When Not in the Room
lf the room is unoccupied, turn off the ceiling fan to save energy.
Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the counterclockwise direction. The
airflow created by the ceiling fan produces a wind-chill effect, making you
feel cooler. Select a fan speed that provides a comfortable breeze; lower
speeds consume less energy.
Winter Season: Reverse the motor and operate the ceiling fan at a low speed in
the clockwise direction. This produces a gentle updraft, which pushes the warm
air near the ceiling down into the occupied space. Remember to adjust your
thermostat when using your ceiling fan. This simple step can lead to
additional energy and cost savings.
Electrical and Structural Requirements
-
Your new ceiling fan will require a grounded electrical supply Line of AC 110-130V /GOHz and a 15 Amp circuit. According to electrical codes, it is neces sary to use a fan-rated outlet box to support the additional weight and motion associated with a ceiling fan. A fan-rated box will be clearly Labeled as such and is typically designed to support ceiling fans weighing up to 35 pounds.
Fan-rated outlet boxes are available in various ratings and designs. It is essential to ensure that the rating of your ceiling fan outlet box meets the requirements for the specific ceiling fan you are installing. -
If your fan is to replace an existing Light fixture, turn power off at the main fuse box and remove the existing Light fixture.
WARNING
To ensure safety and prevent potential electrical shock, it is not sufficient
to simply turn off the wall switch. Prior to wiring, make sure to turn off the
electricity at the main fuse box. All wiring should be done in accordance with
national and Local electrical codes. Additionally, it is important to properly
ground the ceiling fan as a precautionary measure against possible electrical
shock. Following these guidelines will help ensure the safe installation and
operation of your ceiling fan.
WARNING
Do not use a variable (rheostat) wall controller or dimmer switch to operate
this fan. Doing so can cause damage to the ceiling fan’s remote control unit.
It is recommended to only use the provided remote control.
Installation
Take out the hanging board
Remove the screw from the circular hole. Keep the screw that remaved aside for
use later.
Loosen the other two screws from the two key holes approximately 1/4 tum ,Tum
the key holes of the ceflln1 fan housing from the two screws Loosened
previously and remove the hanging board from the ceflln1 fan.
Attach the hanging board to the outlet box (not included) with
the two jbox screws provided. Secure the hanging board to the ceiling with the
two self-tappf ng screws provided.
Wiring
Connect the”Neutral wire” (white wire) from the ceiling to the white wire of
ceiling fan.
Connect the “Live wire”(black wire) from the ceiling to the black wire of
ceiling fan.
Connect the “Ground wire”
Connect the ground wire (Green) on the hanging board and the ground wire
(green) on the fan with the ground wire interface on the ceiling.
Place the two key holes from the celling fan housing over the two
screws previously loosened from the hanging board. Tum the celllng fan housing
until It locks In place at the end of the key holes. Secure by tightening the
two screws previously loosened and the one screw previously removed.
Installing wall Plate
Attach wall plate using the two screws and two plastic anchors provided In
remote control accessory pack.
Remote Control Operation
(1) All Off
(2) 1-6 Fan Speed
(3) Fan Forward
(4) Timer:1/2/4H| (5) Light on/off
(6) Fan Off/ Match code
(7) Fan Reverse
(8) Natural Wind
---|---
Note:
The remote control has completed the learning and pairing steps before leaving
the factory, and can be used directly after installation.
Remote control pairing method: after turning on the power switch,long press
the “FAN OFF” button on the remote control within 5 seconds . Check code is
done. If not , turn off the power, and repeat it after 1 minute.
Remote control code clearing : within 5 seconds upon turning on , long press
“ALL OFF” button, the lighting off, then the action is done.
The remote control needs 2pcs AAA batteries (not included) if your remote
control does not control the fan and lights ,please follow the steps below to
troubleshooting.
Step 1: Replace the battery of the remote control.
Step 2: Try to pair code the remote control again.
Troubleshooting
| Problem | Solution |
|---|---|
| The fan will not start. | ◼ Check the main and branch circuit fuses or |
breakers.
◼ Check the line wire connections to the fan.
◼ Check the battery in the remote control.
◼ Ensure you are in the normal range of 10-20 feet.
◼ Turn the main power source off and then restore the power to the unit.
Within 3 seconds of turning the fan’s AC power ON,press and hold the “ON/OFF”
button for 5 seconds to complete the “pairing process”. Once the receiver has
detected the set frequency, the LED light of the fan will blink once.
The fan is noisy.| ◼ Ensure all motor housing screws are snug.
◼ Ensure the wire nut connections are not rattling against each other.
◼ Allow a 24-hour “breaking in” period. Most noises associated with a new fan
disappear during this time.
◼ Ensure the canopy is a short distance from the ceiling. It should not touch
the ceiling.
◼ Ensure your outlet box is secure and rubber isolator pads were used between
the mounting plate and outlet box.
The fan is wobbles.| ◼ This fan has a one-piece blade design, fan blade
balancing kit is not applicable to this product.
◼ If the fan wobbles, disconnect the power by removing the fuses or turning
off the circuit breakers from the main power source, then check with the
following:
Remove the grille from the fan body by first removing the decorative cap at
the center of the grille by rotating the decorative cap anti-clockwise, use a
Philips screwdriver to tighten the screw inside of the plastic threaded
nipple.
◼ If the wobbling peresits, adjust the angle of the grille slightly to make it
more perpendicular to the ground.
◼ If the problem persists, please contact our customer service.
Fan movesbackwards and forwards when turned on.| ◼ This is normal start-up
procedure for DC motor fans. The partial movement during start-up is the
result of the DC
motor aligning the internal magnetic poles for proper motor operation. This
design saves electricity and allows
the fan to operate much quieter than standard AC motor fans.