Breezary 30007-SN 52 Inch Ceiling Fan With Light Installation Guide

: June 16, 2024
: Breezary

30007-SN 52 Inch Ceiling Fan With Light

Product Information

Specifications:

Product Name: 52 Inch Ceiling Fan with Light
Model Number: ITEM #30007
Customer Service: support@breezary.com

Product Usage Instructions

Installation Instructions (Steps 1-5)

To reduce the risk of fire or injury, do not use this product
with any variable (rheostat) wall control.

Step 1: Assembling the Fan

Take out the fan downrod.
Remove the cotter pin and bolt from the downrod.
Take out the fan motor housing.
Loosen the jam screw in the yoke until it is flush with the
inside surface.
Place the downrod inside the canopy, canopy cover, and yoke
cover.
Route wires exiting the motor through the yoke cover, canopy,
and downrod.
Insert the bolt through the hole in the downrod, being careful
not to damage or cut the fan wires.
Tighten the bolt and secure it with the cotter pin through the
hole in the end of the bolt.
Secure the downrod in position by tightening the jam
screws.
Slide the yoke cover down until it is flush with the motor
housing.

Step 2: Hanging the Fan

Secure the hanger to the metal outlet box.
Hang the ceiling fan on the hanger, aligning the hanger ball
groove with the hanger boss.

Step 3: Attaching the Fan Blades

Attach each blade to the motor using the provided blade
screws.

Step 4: Assembling the Lamp Housing

Feed the wire through the center hole of the lamp housing.
Fix the lamp housing with screws.
Connect the plugs from the motor and LED.

Step 5: Lampshade Installation

Install the lampshade to the lamp housing by turning it
clockwise to lock it into place.

Operation (Step 6-8)

Step 6: Receiver Installation

Put the receiver in the hanger.

Step 7: Wiring the Fan

Follow the wiring diagram below:

Step 8: Attaching the Canopy and Canopy Cover

Slide the canopy up to the ceiling and attach it to the hanger
using the provided screws. Tighten all screws securely.

Troubleshooting Guide

Please refer to the Troubleshooting Guide section on page 11 of
the user manual for troubleshooting assistance.

Balancing Kit

Refer to the Balancing Kit section on page 12 of the user manual
for instructions on how to use the balancing kit.

FAQ (Frequently Asked Questions)

Q: Can I use a variable wall control with this ceiling

fan?

A: No, to reduce the risk of fire or injury, do not use this
product with any variable (rheostat) wall control.

Q: Where can I find the wiring diagram?

A: The wiring diagram can be found in the Wiring the Fan section
on page 8 of the user manual.

Q: How do I balance the ceiling fan?

A: Instructions on how to use the balancing kit can be found in
the Balancing Kit section on page 12 of the user manual.

52 INCH CEILING FAN WITH LIGHT
ITEM #30007 Customer Service: support@ breezary.com

Installation Instructions………………………………..5-9 Operation……………………………………………………10 Troubleshooting Guide………………………………….11 Balancing Kit ……………………………………………….12
To reduce the risk of fire or injury do not use this product in conjunction with any variable (rheostat) wall control.
2

5.9 in

2.2 in 12 in 13.8 in

S1 S2 S3 S4

OFF ON/ OFF

F

R

3

2

4

SET

UP

1

STO

5

P

6

1H

4H

8H

2
3 4 5
6

52 in

S5

Hardware Package

S6

S1.Machine Screw

S2.Washer

S3.Wood Screw

S7

S4.Washer

S5.Blade Screw

S6.Wire Nut S7.Balance Kit

Item name

7

1.Remote Control

2.Hanger

3.Canopy

8

4.Canopy Cover

5.Yoke Cover

6.Dwonrod

7.Long Dwonrod

8.Motor Housing

9

9.Lamp Housing

10.Lamp Shade

11.Blade

10

3

Quantity
2 2 4 4 7 3 1
1 1 1 1 1 1 1 1 1 1 3

Receiver
Bolt jam Screws Blade Blade Screw Lamp housing screw Lamp shade
4

Hanger Canopy screw Hanger Ball Canopy Canopy Cover Yuke Cover Cotter Pin
Motor Housing
Lamp Housing

– Take out fan downrod.
– Remove cotter pin and bolt from downrod. – Take out fan motor housng. – Loosen jam screw in yoke until it is flush with the inside surface. – Place the downrod inside the canopy, canopy cover, and yoke cover.
– Route wires exiting motor through yoke cover, canopy and downrod. – Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires. – Tighten bolt. Secure with cotter pin through hole in the end of the bolt. – Secure downrod in position by tightening jam screws.
– Slide yoke cover down and it will flush with the motor housing.

Fig.1a Cotter Pin

Fig.1b

Downrod

Jam Screw

Bolt

Fig.1c Yoke

Fig.1d
Yoke Cover Bolt

Downrod
Canopy Canopy Cover
Cotter Pin Yoke

Fig.1e Jam Screw
Jam Screw

Downrod Canopy
Canopy Cover
Yoke Cover
Motor

5

Step2

– Secure hanger to metal outlet box.
– The ceiling fan is hung on the hanger, with the hanger ball groove aligned with the hanger boss.

Fig.2a

Fig.2b

Fig.2c

washer

Outlet Box Hanger

Outlet Box Screw not provided

hanger boss hanger ball groove

Outlet Canopy Canopy
Yoke cover Motor

Step3 Attaching the Fan Blades.
– Attach the blade to the motor with blade screws. – Repeat this step for each blade assembly.
Fig.3

Blade screw

Blade

6

Step4 Assembling the lamp housing
– Feed the wire through the center hole of the lamp housing. – Fix the lamp housing with screws. – Connect the plugs from the motor and LED.
Fig.4a

Fig.4b FROM MOTOR

LIGHT(N) LIGHT(L)

Lamp housing
LED Screw

LIGHT(N) LIGHT(L)

FROM LED

Step5 The lampshade installation
– Install the lampshade to the lamp housing by turning clockwise to lock it into place.
Fig.5

1

2

7

Step6 The receiver installation
– Put the receiver in the hanger.
Fig.6a

Fig.6b

Step7 Wiring the Fan
– Wiring according to the wiring diagram. Fig.7a

Form ceiling

white black

white blue

Form fan

grounding wires (From ceiling)
grounding wires (From receiver)

grounding wires (From fan)

8

Step8 Attaching the Canopy and Canopy cover
– Slide the canopy up to the ceiling and attach it to the hanger with the screws provided. Tighten all screws securely.
– Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism)

Fig.8a

Fig.8b

Fig.8c

Canopy

hanger screw
2

Canopy cover

1

CONGRATULATIONS! YOU HAVE COMPLETED THE INSTALLATION
9

FUNCTION INSTRUCTION OF EMITTER Learning code and matching mode are used between the emitter and receiver. – Open the battery cover on the hand-held remote and install a battery, pair of AAA emitter(1.5V) that are not included.
– If the emitter can not control the fan, please pair the code. Turn on the power switch, and press the”SETUP” key within 3 seconds, the receiver issues”tick” two sounds, and the pair code is successful. If not successful, turn off the power for a minute and repeat the above.
-When the emitter cannot control the receiver, please check whether the battery switch is touching normally or not, correction of the positive and negative, and full or empty of power.
-When the emitter cannot control the receiver, please check if is there any existence of similar controlled products with the same frequency that will disturb each other remote-controlled products nearby, then check whether they work, because a remote controlled product with the same frequency will disturb each other.
-Please take out the battery from the emitter when left unused for a long time.
– When installing the fan, the fan ceiling cover doesn’t press the antenna(or other wire), it is easy to break down the wire and short-circuit.

1 All off 2 Fan forward
3 Natural wind 4 Speed controller 5 Match code/Fan off 6 Timer 7 Light on/off
(Three color temperatures are available)
8 Fan reversal

1

OFF

ON/OFF

7

2

F

R

8

3

4

2 4 STOP

1 5 SETUP