Breezary 30014-AB-NL Ceiling Fans Without Light Installation Guide

Breezary 30014-AB-NL Ceiling Fans Without Light

Product Information

Specifications:

• Product Type: Ceiling Fan
• Model Number: ITEM #30014-AB-NL
• Customer Service: support@breezary.com

Installation Instructions

To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control. Follow the steps below for installation:

• Step 1: Downrod and Motor Housing Assembly

  • Take out the fan downrod.
  • Remove the cotter pin and bolt from the downrod.
  • Take out the fan motor housing.
  • Loosen the jam screw in the yoke until it is flush with the inside surface.
  • Place the downrod inside the canopy, canopy cover, and yoke cover.
  • Route wires exiting the motor through the yoke cover, canopy, and downrod.
  • Insert the bolt through the hole in the downrod, being careful not to damage or cut the fan wires.
  • Tighten the bolt and secure it with the cotter pin through the hole in the end of the bolt.
  • Secure the downrod in position by tightening the jam screws.
  • Slide the yoke cover down until it is flush with the motor housing.
  • CAUTION: To ensure wobble-free operation and avoid damaging the fan, make sure the downrod and set screw arecompletely tightened.

• Step 2: Mounting the Fan
  WARNING: To reduce the risk of fire, electric shock, or personal injury, mount the fan to a UL/CSA listed outlet box marked acceptable for fan support and use the mounting screws provided with the outlet box. Follow the steps below:

  • Secure the hanger to the metal outlet box.
  • Hang the ceiling fan on the hanger bracket, aligning the hanger ball groove with the hanger projection.

• Step 3: Attaching the Fan Blades
  Attach each blade to the motor using blade screws and washers. Repeat this step for each blade assembly.

• Step 4: Assembling the Cover
  Install the lamp cover to the motor by turning it clockwise to lock it into place.

• Step 5: Receiver Installation
  Put the receiver in the hanger bracket.

• Step 6: Wiring the Fan
  Wiring according to the wiring diagram:

  • From Ceiling:
  • N wire (white)
  • L wire (black)
  • From Fan:
  • Yellow wire
  • Red wire
  • Gray wire
    Note: Once ground wires are connected, carefully tuck all wires into the metal box, making sure that the wires are clear of the hemisphere and downrod when positioned in the mounting bracket.

Troubleshooting Guide

If you encounter any issues during the installation or operation of the ceiling fan, refer to the troubleshooting guide provided in the user manual.

Balancing Kit

A balancing kit is included with the product to ensure smooth and balanced operation of the ceiling fan. Follow the instructions provided in the balancing kit for proper usage.

FAQ (Frequently Asked Questions):

• Can I use a variable wall control with this ceiling fan?
  No, to reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control.

• How do I clean the fixture?
  Turn off the power, wait for it to cool, and wipe the fixture with a clean, dry, soft cloth.

• Do I need to check and retighten the screws beforeinstallation?
  Yes, all screws must be checked and retightened where necessary before installation.

Safety Information

READ AND SAVE THESE INSTRUCTIONS.

1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before you begin.
2. All wiring must be in accordancce with the National Electrical Code “ANSI/NFPA 70” and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. The outlet box and support structure must be securely mounted and capable of reliably supporting a minimum of 35 lbs (15.9 kg). Use only UL Listed outlet boxes marked” Acceptable for Fan Support of 35 lbs. (15.9 kg) or less.”
4. Do not place objects in the path of the blades.
5. To clean the fixture ,turn off the power, wait for it to cool, and wipe the fixture with a clean dry, soft cloth.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment grounding conductor on one side of the outlet box and ungrounded conductor on the other side of the outlet box.
7. All screws must be checked and retightened where necessary before installation.

• WARNING: To reduce the risk of electrical shock or fire, not use this fan with any solid-state fan speed control device. It will permanently damage the electronic circuitry.
• WARNING: To reduce the risk of fire or injury do not use this product in conjunction with any variable (rheostat) wall control.
• WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing the rackets balancing the blades, or cleaning the fan. Do not insert objects.
• WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support of 35 Ibs. (15.9 Kg) or less” and use screws provided with the outlet box.
• WARNING: To avoid possible electrical shock, turn the electricity off at the main fuse box before wiring.
• WARNING: To reduce the risk of electrical shock, this must be installed with an isolating wall control / switch.
• CAUTION: To reduce the risk of personal injury, use only the screws provided with the outlet box.
• CAUTION: Please use carefully when working around or cleaning the fan to avoid injury or damage of fan.
• CAUTION: The fan must be mounted with a minimum of 7 ft (2.1 m) clearance from the trailing edge of the blades to the floor.
• CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Dimension Reference

Hardware Included

• S1.Machine Screw 2x
• S2.Washer 4x
• S3.Wood Screw 4x
• S4.Wire Nut 3x
• S5.Blade Screw 20x
• S6.Balance Kit 1x
• S7.Expansion Screw 2x

Fan Parts Included

1. Remote Control 1x
2. Hanger Bracket 1x
3. Canopy 1x
4. Canopy Cover 1x
5. Yoke Cover 1x
6. Downrod 1x
7. Long Downrod 1x
8. Motor Housing 1x
9. Cover 1x
10. Blade 6x

Exploded View

INSTALLATION INSTRUCTION

• STEP 1 MOUNTING
  • Take out fan downrod.
  • Remove cotter pin and bolt from downrod.
  • Take out fan motor housng.
  • Loosen jam screw in yoke until it is flush with the inside surface.
  • Place the downrod inside the canopy, canopy cover, and yoke cover.
  • Route wires exiting motor through yoke cover, canopy and downrod.
  • Insert bolt through hole in and downrod. Be careful not to damage or cut the fan wires.
  • Tighten bolt. Secure with cotter pin through hole in the end of the bolt.
  • Secure downrod in position by tightening jam screws.
  • Slide yoke cover down and it will be flush with the motor housing.
    CAUTION: To ensure wobble-free operation and not to avoid damaging to the fan, the downrod and the set crew must be completely tightened.

• Step 2 INSTALL BRACKET
  WARNING: To reduce the risk of fire, electric shock, or personal Injury, mount to UL/CSA listed outlet box marked acceptable for fan support and use mounting screws provided with the outlet box

  •  Secure hanger to metal outlet box.
  • The ceiling fan is hung on the hanger bracket, with the hanger ball groove aligned with the hanger projection.

• Step 3 Attaching the Fan Blades.
  • Attach the blade to the motor with blade screws and washer.
  • Repeat this step for each blade assembly.

• Step 4 Assembling the Cover.
  Install the lamp cover to the Motor by turning clockwise to lock it into place.

• Step 5 The receiver installation
  Put the receiver in the hanger bracket.

• Step 6 Wiring the Fan
  Wiring according to the wiring diagram.

NOTE: Once ground wires are connected, carefully tuck all wires into the metal box making sure that the wires are clear of the hemisphere and downrod when positioned in hemisphere and downrod when positioned in mounting bracket.

• Step 7 Attaching the Canopy and Canopy cover
  •  Slide the canopy up to the ceiling and attach it to the hanger bracket with the screws provided. Tighten all screws securely.
  • Move the Canopy cover onto the canopy. (the decorative cover comes with magnetism)

• CONGRATULATIONS!
  YOU HAVE COMPLETED THE INSTALLATION

FUNCTION INSTRUCTION OF REMOTE CONTROL

• Open battery cover on the hand-held remote and install battery, pair of AAA of remote control(1.5V) that are not included.
• If the emitter can not control the fan, learning code matching mode is used between remote control and receiver.
• Turn on the power switch, press the”SETUP”key within 3 seconds, the receiver issued a”tick”two sounds, the pair code is successful. If not successful, turn off the power for a minute and repeat the above.
• When the remote control cannot control the receiver, please check the battery switch touching normally or not, correction of the positive and negative, full or empty of the power.
• When the remote control cannot control the receiver, please check is there any existence of similar remote controlled products nearby, then check whether they works, because remote controlled product with the same frequency will disturb each other.
• Please remove the battery from the remote control when not in use for a long time.
• When installing the fan, the fan ceiling cover don’t press the antenna(or other wire), it is easy to breakdown the wire and short-circuited.

BUTTON FUNCTION

1. All off

2. Fan forward

3. Natural wind

4. Speed controller

5. Match code/Fan off

6. Timer

7. Light on/off
   (Three color temperatures are available)

8. Fan reversal
   Notice:
   This mode of ceiling fan is without light.

Troubleshooting Guide

If you have difficulty operating your new ceiling fan it may be the result of incorrect assembly,installation,or wiring.In some cases these installation errors may be mistaken for defects.If you experience any faults please check this troubleshooting guide.

Balancing Kit

The Balancing kit should only be used if there is an unacceptable amount of fan wobble after completing all the steps in your Owners Manual under “Attaching The Fan Blades.”

1. Turn the fan on and set the speed control setting to a speed at which the wobbles is the greatest.
2. Turn off the fan and allow it to a come to a complete stop. Select one blade and place the balance clip on it, halfway between the blade holder and the blade tip on the trailing edge of blade.
3. Turn the fan on. Observe whether the wobble has increased or decreased. Turn the fan off, move the clip to another blade, and retest. Repeat this procedure on all blades noting the blade on which the greatest improvement is achieved.
4. Move the clip back to the blade that showed the greatest improvement. Move the clip inward and outward on this blade and operate the fan to find the position where the clip gives the greatest improvement.
5. Remove the clip and install a balancing weight to the top of blade along the center line near the point where the clip was positioned.
6. If the fan wobble problem has not been corrected you may wish to try to improve the balancing further by using the balancing clip and additional weights.

References

• Breezary Ceiling Fan - Online Ceiling Fan Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>