Xinqi EM8 Smart Wireless Meat Thermometer User Manual
- June 16, 2024
- Xinqi
Table of Contents
EM8 Smart Wireless Meat Thermometer
User Manual
EM8 Smart Wireless Meat Thermometer
SMART WIRELESS
MEAT THERMOMETER
FIRST TIME SETUP
-
Open the App Store search and download the “Meat S” app, and you can also find the instructions in the top left corner of the App.
-
Place the probe on the charger, insert a new AAA battery, and click the button to activate the booster. Charge for at least 4 hours before the first use.
-
Use the Meat S app:
First, activate the probe and press the charger button.
Second, Activate the relay, take out the probe, and press and hold the relay for 3 seconds to match. After success, the top of the APP interface will display “connected”, and the green light of the relay will flash.
Third, choose the type of barbecue and cooking method or manually set the target temperature.
Fourth, the app monitors the internal temperature of the meat in real time and sends a notification to your smart device.
Fifth, enjoy the delicious food.
After the device is dormant, the relay must be activated before each use. -
You can now remove the probe from the booster, insert it fully into the meat, and place the meat in the oven. When the probe is fully charged, the indicator light goes off.
-
After enjoying the roast, let the probe cool down and wash the probe, and then put it back in the booster, which automatically closes when it is not in use.
-
The probe placed in the booster will automatically charge to prepare for the next use.
CAUTION
Stainless steel probes can withstand up to 185°F/85°C temperature, while the
ceramic handle can withstands temperatures up to 527°F/275°C.
Above these temperatures may damage this probe.
The probe automatically shuts off after 30 minutes if not in a heat source.
Insert the probe fully into the meat, this allows the probe to withstand the
heat.
Do not use probe when cooking over high heat or over hot coals/flame.
Do not use the probe in a microwave or pressure cooker.
The probe can become very hot during and after use. Wear heat-resistant gloves
when handling the probe.
Probes can be put into the dishwasher. During cooking, fry in a deep fat fryer
without damage.
Do not soak it in water when unused.
PROBE& BOOSTER
The probe can be used for more than 24 hours after full charge.
INDICATOR LIGH
| Device Status | Status Meaning |
|---|---|
| Working Status Indicator | The green light flashes, indicating that the device |
is connected.
The red light flashes, indicating that the probe is disconnected from the
booster.
Alternately flashing red and blue lights indicate it is pairing and
connecting.
he connection status red light flashes, indicating that the probe is being
searched.
A flashing blue light indicates that the probe is connected.
When the light is off, the device is in sleep mode or the battery is low.
Booster Power Indicator| Green light flashes, indicating sufficient power.
Flashing red light indicates low battery.
Probe Power Indicator| Green light flashes, indicating sufficient power.
Flashing red light indicates low battery.
hibernation/shutdown state| In shutdown state, press the relay button to
activate the relay and probe Connected state, put the probe into the relay to
charge, the relay sleeps and shuts down
In working state, keep the temperature below 50°C, the relay and probe will
sleep and shut down within 30 minutes
Disconnected state, the probe and relay are disconnected. sleep and shut down
within 5 minutes
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>