FL SWITCH 1005N Unmanaged Narrow Ethernet Switches User Manual

FL SWITCH 1005N Unmanaged Narrow Ethernet Switches

Unmanaged narrow Ethernet switches
User manual
UM EN FL SWITCH 1000
UM EN FL SWITCH 1000, Revision A
2023-01-20

This user manual is valid for:

4138_en_A

For your safety

Read this user manual carefully and keep it for future reference.

1.1 Labeling of warning notes

This symbol indicates hazards that could lead to personal injury.
There are three signal words indicating the severity of a potential injury.
DANGER
Indicates a hazard with a high risk level. If this hazardous situation is not avoided, it will result in death or serious injury.
WARNING
Indicates a hazard with a medium risk level. If this hazardous situation is not avoided, it could result in death or serious injury.
CAUTION
Indicates a hazard with a low risk level. If this hazardous situation is not avoided, it could result in minor or moderate injury.
This symbol together with the NOTE signal word warns the reader of actions that might cause property damage or a malfunction.
Here you will find additional information or detailed sources of information.

1.2 Qualification of users
The use of products described in this user manual is oriented exclusively to:
– Qualified electricians or persons instructed by them. The users must be familiar with the relevant safety concepts of automation technology as well as applicable standards and other regulations.
– Qualified application programmers and software engineers. The users must be familiar with the relevant safety concepts of automation technology as well as applicable standards and other regulations.
1.3 Product changes
Changes or modifications to hardware and software of the device are not permitted. Incorrect operation or modifications to the device can endanger your safety or damage the device. Do not repair the device yourself. If the device is defective, please contact  Phoenix Contact.
1.4 Security in the network

NOTE: Risk of unauthorized network access
Connecting devices to a network via Ethernet entails the danger of unauthorized access to the network.
To prevent unauthorized network access, please read the following notes:

• If possible, deactivate unused communication channels.
• Assign passwords such that third parties cannot access the device and make unauthorized changes.
• Due to its communication interfaces, the device should not be used in security-critical applications unless additional security appliances are used. Therefore, please take additional protective measures in accordance with the IT security requirements and the standards applicable to your application, e.g., virtual networks (VPN) for remote maintenance access, firewalls, etc., for protection against unauthorized network access.
• On first request, you shall release Phoenix Contact and the companies associated with Phoenix Contact GmbH & Co. KG, Flachsmarkstrasse 8, 32825 Blomberg, Germany in accordance with §§ 15 ff AktG (German Stock Corporation Act), hereinafter  collectively referred to as “Phoenix Contact”, from all third-party claims made due to improper use.
• For the protection of networks for remote maintenance via VPN, Phoenix Contact offers the mGuard product series of security appliances; these are described in the latest Phoenix Contact catalog (phoenixcontact.net/products).
• Additional measures for protection against unauthorized network access are listed in the AH EN INDUSTRIAL SECURITY application note. The application note can be downloaded at phoenixcontact.net/products).

1.5 UL notes

WARNING:
his equipment is an open-type device meant to be installed in an enclosure suitable for the environment that is only accessible with the use of a tool. This equipment is suitable for use in Class I, Division 2, Groups A, B, C, and D or nonhazardous locations only. The wire temperature rating must be at least 105°C. The equipment shall only be used in an area of not more than pollution degree 2, as defined in IEC/EN 60664-1. If the equipment is used in a manner not specified, the protection provided by the equipment may be impaired. The device must not be opened or modified. Do not attempt to repair the device yourself but replace it with an equivalent device. Repairs may only be carried out by the manufacturer. The manufacturer is not liable for damage resulting from failure to comply.

Overview and ordering data

2.1 Descriptions
FL SWITCH product descriptions are coded to signify its configuration.
Figure 2-1 FL SWITCH nomenclature

Table 2-1 Nomenclature key

6 = 10/100 Mbps IP67
7 = 1000 Mbps IP67
Number of RJ45 ports| D| As shown
Structure| E| N = Narrow form factor
Environment| F| T = Wide temperature
Coating| G| C = Conformal coating
Connections| H| ST = ST fiber optic connectors SC = SC fiber optic connectors LC = LC fiber optic connectors
SFX = Port for small 10/100 Mbps form-factor mod- ules
SFP = Port for small 100/1000 Mbps form-factor modules

FL SWITCH 10…N and FL SWITCH 11…N
The FL SWITCH 10…N and FL SWITCH 11…N Ethernet switches provide basic, cost- effective switch functions. They include automatic detection of data transmission rates and autocrossing with up to two fiber optic interfaces.

• Auto negotiation and autocrossing detection simplifies installation and setup
• Local diagnostic indicator LEDs
• RJ45 ports support a transmission speed of 10/100 Mbps on FL SWITCH 10… switches and 10/100/1000 Mbps on FL SWITCH 11… switches
• QoS prioritization support
• PROFINET conformance Class A for real-time data exchange
•  Energy-efficient Ethernet in accordance with IEEE 802.3az
• PROFINET PTCP filter for reliable communication on PROFINET networks
• Enhanced traffic prioritization for automation protocols

FL SWITCH 10…NT and FL SWITCH 11…NT
The FL SWITCH 10…NT and FL SWITCH 11…NT Ethernet switches provide basic switch functions in a robust housing with expanded temperature and installation ranges. They include automatic detection  of data transmission rates and autocrossing with up to two fiber optic interfaces.

• Auto negotiation and autocrossing detection simplifies installation and setup
•  Local diagnostic indicator LEDs
•  RJ45 ports support a transmission speed of 10/100 Mbps on FL SWITCH 10… switches and 10/100/1000 Mbps on FL SWITCH 11… switches
• QoS prioritization support
• PROFINET conformance Class A for real-time data exchange
• Energy-efficient Ethernet in accordance with IEEE 802.3az
• PROFINET PTCP filter for reliable communication on PROFINET networks
• Enhanced traffic prioritization for automation protocols

2.1.1 SFP module compatibility
Table 2-2 SFP module compatibility

2.2 Ordering data

Industrial Ethernet switch, five RJ45 ports with 10/100 Mbps, automatic speed detection, autocrossing, QoS| FL SWITCH 1005N| 1085039| 1
Industrial Ethernet switch, eight RJ45 ports with 10/100 Mbps, automatic speed detection, autocrossing, QoS| FL SWITCH 1008N| 1085256| 1
Industrial Ethernet switch, five RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS| FL SWITCH 1105N| 1085254| 1
Industrial Ethernet switch eight RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS| FL SWITCH 1108N| 1085243| 1
Industrial Ethernet switch, 16 RJ45 ports with 10/100 Mbps, automatic speed detection, autocrossing, QoS| FL SWITCH 1016N| 1085255| 1
Industrial Ethernet switch, sixteen RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS| FL SWITCH 1116N| 1085219| 1
Description […]| Type| Order No.| Pcs./Pkt
---|---|---|---
Industrial Ethernet switch, four RJ45 ports with 10/100 Mbps, one SC-D fiber optic port with 100 Mbps, au- tomatic speed detection, autocrossing, QoS| FL SWITCH 1004N-FX| 1084159| 1
Industrial Ethernet switch, four RJ45 ports with 10/100 Mbps, one ST fiber optic port with 100 Mbps, auto- matic speed detection, autocrossing, QoS| FL SWITCH 1004N-FX ST| 1085179| 1
Industrial Ethernet switch, four RJ45 ports with 10/100 Mbps, one SC fiber optic port with 100 Mbps, auto- matic speed detection, autocrossing, QoS| FL SWITCH 1004N-FX SM| 1085214| 1
Industrial Ethernet switch, four RJ45 ports with 10/100 Mbps, one SFP port with 100 Mbps, automatic speed detection, autocrossing, QoS| FL SWITCH 1004N- SFX| 1085177| 1
Industrial Ethernet switch, four RJ45 ports with 10/100/1000 Mbps, one SFP port with 100/1000 Mbps, au- tomatic speed detection, autocrossing, QoS| FL SWITCH 1104N-SFP| 1085173| 1
Industrial Ethernet switch, five RJ45 ports with 10/100 Mbps, two SFP ports with 100 Mbps, automatic speed detection, autocrossing, QoS| FL SWITCH 1005N- 2SFX| 1085176| 1
Industrial Ethernet switch, five RJ45 ports with 10/100/1000 Mbps, two SFP ports with 100/1000 Mbps, au- tomatic speed detection, autocrossing, QoS| FL SWITCH 1105N-2SFP| 1085171| 1
Industrial Ethernet switch, eight RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS, wide temperature range| FL SWITCH 1108NT| 1085162| 1
Industrial Ethernet switch, five RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS, wide temperature range| FL SWITCH 1105NT| 1085163| 1
Industrial Ethernet switch, five RJ45 ports with 10/100 Mbps, two SFP ports with 100 Mbps, automatic speed detection, autocrossing, QoS, wide temperature range| FL SWITCH 1006NT-2SFX| 1085164| 1
Industrial Ethernet switch, eight RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS, wide temperature range| FL SWITCH 1008NT| 1085165| 1
Industrial Ethernet switch, four RJ45 ports with 10/100 Mbps, one SFP ports with 100 Mbps, automatic speed detection, autocrossing, QoS, wide temperature range| FL SWITCH 1004NT-SFX| 1085169| 1
Industrial Ethernet switch, five RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS, wide temperature range| FL SWITCH 1005NT| 1085170| 1
Industrial Ethernet switch, twelve RJ45 ports with 10/100 Mbps, two SFP ports with 100/1000 Mbps, auto- matic speed detection, autocrossing, QoS, wide tempera- ture range| FL SWITCH 1012NT-2SFP| 1249598| 1
Description […]| Type| Order No.| Pcs./Pkt
---|---|---|---
Industrial Ethernet switch, 24 RJ45 ports with 10/100 Mbps, automatic speed detection, autocrossing, QoS, wide tem- perature range| FL SWITCH 1024T| 1343027| 1
Industrial Ethernet switch, four RJ45 ports with 10/100/1000 Mbps, one SFP ports with 100/1000 Mbps, au- tomatic speed detection, autocrossing, QoS, wide tempera- ture range| FL SWITCH 1104NT-SFP| 1343023| 1
Industrial Ethernet switch, five RJ45 ports with 10/100/1000 Mbps, two SFP ports with 100/1000 Mbps, au- tomatic speed detection, autocrossing, QoS, wide tempera- ture range| FL SWITCH 1105NT-2SFP| 1343025| 1
Industrial Ethernet switch, 16 RJ45 ports with 10/100/1000 Mbps, automatic speed detection, autocross- ing, QoS, wide temperature range| FL SWITCH 1116T| 1085115| 1
Accessories

Description| Type| Order No.| Pcs./Pkt.
Mounting plate| FL DIN-RAIL ADAPTER 22.5| 1085485| 1
Mounting plate| FL PANEL ADAPTER 22.5| 1085488| 1
Mounting plate| FL DIN-RAIL ADAPTER 40| 1085484| 1
Mounting plate| FL PANEL ADAPTER 40| 1085486| 1
Patch cable| NBC-R4AC-R4AC-

IE8A/…/…

| 1411854| 1
Patch cable| NBC-R4AC/10G- R4AC/10G-94F/2.0| 1408360| 1
Patch cable| NBC-R4AC/10G- R4AC/10G-94F/3.0| 1408365| 1
Patch cable| NBC-R4AC/1,0-93B/R4AC| 1408968| 1
Patch cable| NBC-R4AC/2,0-93B/R4AC| 1408969| 1
Patch cable| NBC-R4AC/5,0-93B/R4AC| 1408970| 1
Patch cable, FO, 1 m| FOC-LC:PA-SC:PA- OM2:D01/1| 1115607| 1
Patch cable, FO, 2 m| FOC-LC:PA-SC:PA- OM2:D01/2| 1115605| 1
Patch cable, FO, 1 m| FOC-LC:PA-LC:PA- OM2:D01/1| 1115633| 1
Patch cable, FO, 2 m| FOC-LC:PA-LC:PA- OM2:D01/2| 1115634| 1
Patch cable, fiber optic, 1 m| FOC-LC:PA-ST:PA- OM2:D01/1| 1115588| 1
Patch cable, fiber optic, 2 m| FOC-LC:PA-ST:PA- OM2:D01/2| 1115587| 1
Accessories […]

Description| Type| Order No.| Pcs./Pkt.
Patch cable, FO, 1 m| FOC-LC:PA-SC:PA- OM4:D01/1| 1115601| 1
Patch cable, FO, 2 m| FOC-LC:PA-SC:PA- OM4:D01/2| 1115600| 1
Patch cable, FO, 1 m| FOC-LC:PA-LC:PA- OM4:D01/1| 1115625| 1
Patch cable, FO, 2 m| FOC-LC:PA-LC:PA- OM4:D01/2| 1115624| 1
Patch cable, FO, 1 m| FOC-LC:PA-LC:PA- OS2:D01/1| 1115636| 1
Patch cable, FO, 2 m| FOC-LC:PA-LC:PA- OS2:D01/2| 1115629| 1
Patch cable, FO, 1 m| FOC-LC:PA-ST:PA- OS2:D01/1| 1115596| 1
Patch cable, FO, 2 m| FOC-LC:PA-ST:PA- OS2:D01/2| 1115595| 1
Patch cable, FO, 1 m| FOC-LC:PA-SC:PA- OS2:D01/1| 1115618| 1
Patch cable, FO, 2 m| FOC-LC:PA-SC:PA- OS2:D01/2| 1115617| 1
End clamp| E/NS 35 N| 0800886| 1
Patch cable| FL CAT5 PATCH 0.5| 2832263| 1
Patch cable| FL CAT5 PATCH 1.0| 2832276| 1
Patch cable| FL CAT5 PATCH 2.0| 2832289| 1
PCB connector| FKCT 2.5/3-ST KMGY BD:US, GND| 1087544| 1
PCB connector| FKCT 2.5/3-ST KMGY| 1998263| 1
Dust protection| FL RJ45 PROTECT CAP| 2832991| 1
Surge protection device| DT-LAN-CAT .6+| 2881007| 1
Visit phoenixcontact.net/products for available accessories| | |

Installation

3.1 DIN rail
3.1.1 Mounting
Place the module on a grounded DIN rail from above using the slot (A). Push the front of the module toward the mounting surface until it audibly snaps into place (B).

3.1.2 Removal
Insert a suitable tool into the latch of the holding clamp and pull the latch downward by pushing the tool upward (A). Pull out the lower edge (B) and then remove the module from the rail.

3.2 Power
WARNING:
This device is designed for SELV and PELV operation according to IEC 61140/ EN 61140.
The switch connects to a single power source through a removable COMBICON connector.
Snapping the switch onto a grounded rail connects it to the ground potential.
Protective ground is through the DIN rail.
In an environment particularly prone to EMI, noise immunity can be increased by an additional low-impedance connection to functional earth ground.

Table 3-1 Current rating

3.2.1 Derating

FL SWITCH 10…N and
FL SWITCH 11…N

When installed on a horizontal rail, the Ethernet switches may be mounted immediately next to one another without derating the temperature (c > 0 mm).

FL SWITCH 10…NT and FL SWITCH 11…NT

When installed on a vertical rail, the Ethernet switches may be mounted immediately next to one another. However, the maximum temperature must be reduced by 5°C (c = 0 mm).
See “Technical data” on page 19 for maximum temperature rating.
When installed on a horizontal rail, the Ethernet switches may be mounted immediately next to one another without derating the temperature (c > 0 mm).
When installed on a vertical rail, the Ethernet switches may be mounted immediately next to one another. However, the maximum temperature must be reduced by 5°C (c = 0 mm).
See “Technical data” on page 19 for maximum temperature rating.

Operation

4.1 Diagnostic and status indicators
A Link/ACT LED corresponding to the port number indicates the status of that port.

Table 4-1 LED indicators

Ports

| Link/ACT| On| Link established and network avail- able
| Flashing| Data transmission active
| Off| No link established. Network not com- municating.
Switch LED
| US| On| Power is present
| Off| Power is not present

4.2 SFP modules
SFP ports are rated at 100 Mbps (FL SWITCH…SFX …) or 100/1000 Mbps (FL SWITCH…SFP …).
The listed Ethernet switches (see “SFP module compatibility” on page 9) provide 3.3 V DC to power the SFP module.
Installed SFP modules must have an insulation material rating of V-2 and be a Class 1 laser product.

Technical data

5.1 FL SWITCH 1005N (Order No. 1085039)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Free from substances that could impair the application of
coating| In acc. with VW specification
General data

Mounting type| DIN rail
Weight| 129.9 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 167.2 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
MTTF| 1627 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 1526 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 5
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 V pp (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 19 mA
Max. current consumption| 110 mA
Mechanical tests

Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields) Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields) Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, KC, UL Listed, IECEE CB Scheme

5.2 FL SWITCH 1008N (Order No. 1085256)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 173.2 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 133.9 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
MTTF| 1254 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 1196 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week,
8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 8
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 28 mA
Max. current consumption| 173 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields) Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields) Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, KC, UL Listed, IECEE CB Scheme

5.3 FL SWITCH 1105N (Order No. 1085254)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Weight| 135.1 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 87.5 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
MTTF| 1058 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 951 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8
hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 5
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 V
(within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 38 mA
Max. current consumption| 311 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA| UL 61010-1
UL, USA/Canada| Class I, Div. 2, Groups A, B, C, D T4
Class I, Zone 2, IIC T4
Further approvals| cUL Listed, EAC, KC, UL Listed, CC-Link IE Field, IECEE CB Scheme

5.4 FL SWITCH 1108N (Order No. 1085243)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Weight| 179.2 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 4k
MTTF| 66.1 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
MTTF| 786 Years (SN 29500 standard, temperature 25°C, operating
cycle 21%)
MTTF| 709 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 8
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 54 mA
Max. current consumption| 452 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, KC, UL Listed, IECEE CB Scheme

5.5 FL SWITCH 1016N (Order No. 1085255)

Dimensions (nominal sizes in mm)

Width| 40 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data|
Mounting type| DIN rail
Weight| 265.9 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 8k
MTTF| 63.7 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
MTTF| 729 Years (SN 29500 standard, temperature 25°C, operating
cycle 21%)
MTTF| 639 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 16
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 68 mA
Max. current consumption| 266 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, KC, UL Listed, IECEE CB Scheme

5.6 FL SWITCH 1116N (Order No. 1085219)

Dimensions (nominal sizes in mm)

Width| 40 mm
Height| 151 mm
Depth| 98 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Weight| 455 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 8k
MTTF| 77.4 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 833.6 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 616.1 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 16
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 195 mA
Max. current consumption| 344 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4

5.7 FL SWITCH 1004N-FX (Order No. 1084159)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 115.1 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 427.5 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 279.5 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 4
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: Ethernet FO
Number of interfaces| 1
Connection method| SC
Transmission physics| multi-mode fiberglass
Transmission speed| 100 Mbps (full duplex)
Transmission length| 8 km (fiberglass with F-G 62.5/125 0.7 dB/km F1000)
Transmission length| 4.29 km (fiberglass with F-G 50/125 0.7 dB/km F1200)
Wavelength| 1300 nm
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 59 mA
Max. current consumption| 230 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives

Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.8 FL SWITCH 1004N-FX ST (Order No. 1085179)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data

Mounting type| DIN rail
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 115.1 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 427.5 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 279.5 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 4
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: Ethernet FO
Number of interfaces| 1
Connection method| ST
Transmission physics| multi-mode fiberglass
Transmission speed| 100 Mbps (full duplex)
Transmission length| 8 km (fiberglass with F-G 62.5/125 0.7 dB/km F1000)
Transmission length| 5.71 km (fiberglass with F-G 50/125 0.7 dB/km F1200)
Wavelength| 1300 nm
Supply voltage

Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 60 mA
Max. current consumption| 230 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.9 FL SWITCH 1004N-FX SM (Order No. 1085214)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 95.9 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 298.8 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 188.3 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)

Number of interfaces| 4
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: Ethernet FO
Number of interfaces| 1
Connection method| SC
Transmission physics| Single-mode fiberglass
Transmission speed| 100 Mbps (full duplex)
Transmission length| 20 km (fiberglass with F-G 9/125 0.5 dB/km)
Wavelength| 1310 nm
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 51 mA
Max. current consumption| 196 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.10 FL SWITCH 1004N-SFX (Order No. 1085177)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 138.3 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 1647 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 1503.6 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 4
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 1
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Max. current consumption| 162 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives

Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.11 FL SWITCH 1104N-SFP (Order No. 1085173)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data

Mounting type| DIN rail
Housing material| Polycarbonate fiber reinforced
MAC address table| 4k
MTTF| 77.4 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 949.7 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 828.9 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 4
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 1
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 or 1000 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 48 mA
Max. current consumption| 474 mA
Mechanical tests

Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.12 FL SWITCH 1005N-2SFX (Order No. 1085176)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data

Mounting type| DIN rail
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 107.9 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 1346 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 1294.8 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 5
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 2
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 25 mA
Max. current consumption| 252 mA
Mechanical tests

Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.13 FL SWITCH 1105N-2SFP (Order No. 1085171)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -10°C … 60°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Housing material| Polycarbonate fiber reinforced
MAC address table| 4k
MTTF| 59.2 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 872.1 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 836.5 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 5
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 2
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 or 1000 Mbps (full duplex)
Transmission length| Up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 30 mA
Max. current consumption| 681 mA
Mechanical tests

Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.14 FL SWITCH 1108NT (Order No. 1085162)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without derating)
General data
Mounting type| DIN rail
Weight| 280 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 4k
MTTF| 73 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 755.6 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 653.6 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)

Number of interfaces| 8
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 18 mA
Max. current consumption| 121 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields) Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields) Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4

5.15 FL SWITCH 1105NT (Order No. 1085163)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 222 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 4k
MTTF| 97.6 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
MTTF| 888.3 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 818.3 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)+E45:F68

Number of interfaces| 5
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 34 mA
Max. current consumption| 98 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Interface: Ethernet (RJ45)+E45:F69
Number of interfaces| 6
Connection method| RJ46
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 101 m (per segment)
Supply voltage
Supply voltage| 25 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 10 V DC … 32 V DC
Typical current consumption| 162 mA
Max. current consumption| 226 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-3
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T5

5.16 FL SWITCH 1005NT-2SFX (Order No. 1085164)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 263 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 115.8 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 1350.4 Years (SN 29500 standard, temperature 25°C,
operating cycle 21%)
MTTF| 1335.2 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)

Number of interfaces| 6
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 2
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 25 mA
Max. current consumption| 89 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.17 FL SWITCH 1008NT (Order No. 1085165)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 266 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 133.6 Years (MIL-HDBK-217F standard, temperature 25°C, operating cycle 100%)
MTTF| 1254 Years (SN 29500 standard, temperature 25°C, operating cycle 21%)
MTTF| 1203.8 Years (Telcordia standard, 25°C temperature, 21% operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 8
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 26 mA
Max. current consumption| 57 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.18 FL SWITCH 1004NT-SFX (Order No. 1085169)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 205 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 143.4 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 1664.2 Years (SN 29500 standard, temperature 25°C,
operating cycle 21%)
MTTF| 1582.8 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 4
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 1
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 21 mA
Max. current consumption| 59 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives

Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.19 FL SWITCH 1005NT (Order No. 1085170)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 117 mm
Depth| 84 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data

Mounting type| DIN rail
Weight| 222 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 2k
MTTF| 173.1 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 1627.3 Years (SN 29500 standard, temperature 25°C,
operating cycle 21%)
MTTF| 1538.9 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 5
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 21 mA
Max. current consumption| 40 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives

Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4
Further approvals| cUL Listed, EAC, UL Listed

5.20 FL SWITCH 1012NT-2SFP (Order No. 1249598)

Dimensions (nominal sizes in mm)

Width| 40 mm
Height| 140.4 mm
Depth| 92.4 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 433 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 8k
MTTF| 64.3 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 298.8 Years (SN 29500 standard, temperature 25°C, operating
cycle 21%)
MTTF| 560.1 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 12
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 2
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 or 1000 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage

Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 125 mA
Max. current consumption| 223 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4

5.21 FL SWITCH 1024T (Order No. 1343027)

Dimensions (nominal sizes in mm)

Width| 65 mm
Height| 140mm
Depth| 107 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 620 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 8k
MTTF| 64.3 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 298.8 Years (SN 29500 standard, temperature 25°C, operating
cycle 21%)
MTTF| 560.1 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)

Number of interfaces| 24
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 56 mA
Max. current consumption| 370 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A

5.22 FL SWITCH 1116T (Order No. 1085115)

Dimensions (nominal sizes in mm)

Width| 65 mm
Height| 140 mm
Depth| 107 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 631 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 8k
MTTF| 64.3 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 298.8 Years (SN 29500 standard, temperature 25°C, operating
cycle 21%)
MTTF| 560.1 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)

Number of interfaces| 16
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Supply voltage
Supply voltage| 24 V DC
Residual ripple| 3.6 Vpp (within the permitted voltage range)
Supply voltage range| 9 V DC … 32 V DC
Typical current consumption| 191 mA
Max. current consumption| 938 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A

5.23 FL SWITCH 1104NT-SFP (Order No. 1343023)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 123 mm
Depth| 90 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 220 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 8k
MTTF| 64.3 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 298.8 Years (SN 29500 standard, temperature 25°C, operating
cycle 21%)
MTTF| 560.1 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data
Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)

Number of interfaces| 4
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 1
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 or 1000 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V AC/DC
Residual ripple| 3.6 Vpp  (within the permitted voltage range)
Typical current consumption| 9 V DC … 32 V DC
18 V AC … 30 V AC
Supply voltage range| 47 mA
Max. current consumption| 425 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives
Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields)
Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields)
Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates

UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4

5.24 FL SWITCH 1105NT-2SFP (Order No. 1343025)

Dimensions (nominal sizes in mm)

Width| 22.5 mm
Height| 148 mm
Depth| 98 mm
Ambient conditions
Degree of protection| IP30
Ambient temperature (operation)| -40°C … 75°C
Ambient temperature (storage/transport)| -40°C … 85°C
Permissible humidity (operation)| 5% … 95% (non-condensing)
Permissible humidity (storage/transport)| 5% … 95% (non-condensing)
Air pressure (operation)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
Air pressure (storage/transport)| 79 kPa … 108 kPa up to 2000 m above mean sea level (Without
derating)
General data
Mounting type| DIN rail
Weight| 279 g
Housing material| Polycarbonate fiber reinforced
MAC address table| 4k
MTTF| 64.3 Years (MIL-HDBK-217F standard, temperature 25°C,
operating cycle 100%)
MTTF| 298.8 Years (SN 29500 standard, temperature 25°C, operating
cycle 21%)
MTTF| 560.1 Years (Telcordia standard, 25°C temperature, 21%
operating cycle (5 days a week, 8 hours a day))
Connection data

Connection method| Push-in spring connection
Pluggable| Yes
Conductor cross section solid min.| 0.2 mm²
Conductor cross section solid max.| 2.5 mm²
Conductor cross section flexible min.| 0.2 mm²
Conductor cross section flexible max.| 2.5 mm²
Conductor cross section AWG min.| 24
Conductor cross section AWG max.| 12
Stripping length| 10 mm
Interface: Ethernet (RJ45)
Number of interfaces| 5
Connection method| RJ45
Note on the connection method| Auto negotiation and autocrossing
Transmission physics| Ethernet in RJ45 twisted pair
Transmission speed| 10/100/1000 Mbps
Transmission length| 100 m (per segment)
Interface: SFP module
Number of interfaces| 2
Connection method| SFP ports
Transmission physics| Depending on the SFP module
Transmission speed| 100 or 1000 Mbps (full duplex)
Transmission length| up to 40 km (Depending on the fiber/SFP module used)
Supply voltage
Supply voltage| 24 V AC/DC
Residual ripple| 3.6 Vpp (within the permitted voltage range)
Typical current consumption| 9 V DC … 32 V DC
18 V AC … 30 V AC
Supply voltage range| 33 mA
Max. current consumption| 560 mA
Mechanical tests
Mechanical tests| Free fall in accordance with EN 61131-2
Vibration (operation)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Vibration (storage/transport)| in acc. with IEC 60068-2-6: 5g, 150 Hz
Shock (operation)| 30g (EN 60068-2-27)
Conformity with EMC directives

Electromagnetic compatibility| Conformance with EMC Directive 2014/30/EU
Conducted noise emission| EN 61000-6-2 EN 55032 Class A
Interference emission| EN 61000-6-2 EN 61000-4-8 (electromagnetic fields) Criterion A
Immunity to burst| EN 61000-6-2 EN 61000-4-4 (EFT burst) Criterion A
Immunity to EF| EN 61000-6-2 EN 61000-4-3 (electromagnetic fields) Criterion A
Immunity to ESD| EN 61000-6-2 EN 61000-4-2 (ESD) Criterion B
Immunity to surge| EN 61000-6-2 EN 61000-4-5 (surge) Criterion B
Immunity to conducted interference| EN 61000-6-2 EN 61000-4-6 (line noise immunity) Criterion A
Approvals/Certificates
UL, USA/Canada| UL 61010-1, UL 61010-2-201
Class I, Div. 2, Groups A, B, C, D, T4
Class I, Zone 2, Group IIC, T4

Please observe the following notes
General terms and conditions of use for technical documentation
Phoenix Contact reserves the right to alter, correct, and/or improve the technical documentation and the products described in the technical documentation at its own discretion and without giving prior notice, insofar as this is reasonable for the user. The same applies to any technical changes that serve the purpose of technical progress. The receipt of technical documentation (in particular user documentation) does not constitute any further duty on the part of Phoenix Contact to furnish information on modifications to products and/or technical documentation. You are responsible to verify the suitability and intended use of the products in your specific application, in particular with regard to observing the applicable standards and regulations. All information made available in the technical data is supplied without any accompanying guarantee, whether expressly mentioned, implied or tacitly assumed.
In general, the provisions of the current standard Terms and Conditions of Phoenix Contact apply exclusively, in particular as concerns any warranty liability.
This manual, including all illustrations contained herein, is copyright protected. Any changes to the contents or the publication of extracts of this document is prohibited.
Phoenix Contact reserves the right to register its own intellectual property rights for the product identifications of Phoenix Contact products that are used here. Registration of such intellectual property rights by third parties is prohibited.
Other product identifications may be afforded legal protection, even where they may not be indicated as such.

How to contact us

Internet

Up-to-date information on Phoenix Contact products and our Terms and Conditions can be found on the Internet at: phoenixcontact.com
Make sure you always use the latest documentation.
It can be downloaded at: phoenixcontact.net/products
Subsidiaries
If there are any problems that cannot be solved using the documentation, please contact your Phoenix Contact subsidiary.
Subsidiary contact information is available at phoenixcontact.com.
Published by
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
GERMANY
PHOENIX CONTACT Development and Manufacturing, Inc.
586 Fulling Mill Road
Middletown, PA 17057
USA
Should you have any suggestions or recommendations for improvement of the contents and layout of our manuals, please send your comments to: tecdoc@phoenixcontact.com

PHOENIX CONTACT GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany
phoenixcontact.com

References

• Phoenix Contact Australia
• phoenixcontact.net/products
• phoenixcontact.net/products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>