240 Valkyrie Dragonfang Installation Guide

: June 16, 2024
: VALKYRIE

Table of Contents

AIO Water Cooling Parts
WATER COOLING
TIPS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

240 Valkyrie Dragonfang
Installation Guide

AIO Water Cooling Parts

WATER COOLING

Radiator Installation
Step 1: Install fan
Use the fan screws to secure the fan to the radiator.
*Please use the shorter fan screws. DO NOT use extended screws to secure the cooling fan.

Step 2: Install radiator
Use the radiator screws to secure the radiator to the case. Intel LGA1200/1700 Installation
We have marked the parts required for installing the Intel LGA1200/1700 platform for you. Step 1: Install backplate

Align the backplate to the corresponding platform holes.
Install the backplate onto the back of the motherboard.

You may slide it to adjust for alignment with corresponding platform holes.
Use the inner mounting hole position for 1200 (115X) and outer mouting hole position for 1700.

Step 2: Install screws
Install Intel/AMD bolts to the motherboard.
*The larger end of the screw faces down.

Step 3: Removing protective cover
Remove the protective cover from coldplate.

it is critical to the cooling performance. Step 4: Install bracket
Use bracket bolts to install the bracket to the water block.

Step 5: Install water block
Put the water block onto the studs and use nuts to fix it. Step 6: Complete installation
Please refer to the “Wiring” for wiring. Intel LGA2011/2066 Installation
We have marked the parts required for installing the Intel LGA2011/2066 platform for you. Step 1: Install screws
Install Intel LGA2011 bolts to the motherboard.

Step 2: Removing protective cover
Remove the protective cover from the coldplate.
*It is critical to the cooling performance.

Step 3: Install bracket
Use bracket bolts to install the bracket to the water block. Step 4: Install water block
Put the water block onto the studs and use nuts to fix it. Step 5: Complete installation
Please refer to the “Wiring” for wiring. AMD AM4/AM5 Installation
We have marked the parts required for installing the AMD AM4/AM5 platform for you. Step 1: Prepare the motherboard
Screw out the 4 bolts. Remove the original bracket on the motherboard. Keep the original backplate. Step 2: Install screws
Install Intel/AMD bolts to the motherboard. The larger end of the screw faces down. Step 3: Install brackets
Install AMD brackets onto the screws and tighten them with nuts. Step 4: Removing protective cover
Remove the protective cover from the coldplate.
It is critical to the cooling performance. Step 5: Install AMD fastener
Use bracket bolts to install the AMD fastener to the water block. Step 6: Install Water Block
Align bracket to the holes and tighten the spring screws on both ends. Step 7: Complete installation
Please refer to the “Wiring” for wiring.

WIRING

Connecting Water Block to the Motherboard

Connect the water pump 4PIN connector into the AIO_PUMP header on the motherboard.
Plug the water block A-RGB connector into the A-RGB header on the motherboard.

If there is only one A-RGB header on the motherboard, the water block A-RGB connector may be connected to the Valkyrie HUB.

Valkyrie HUB Wiring

Plug the SATA power supply connector into the Valkyrie HUB POWER port.
Plug the 4PIN fan connectors and ARGB connectors into the Valkyrie HUB, respectively.*
Connect Valkyrie HUB control cables to MB_FAN and MB_ARGB ports
respectively and plug the other ends into the CPU_FAN and AGRB headers on the motherboard.
*The FAN_01 (red) on the VK HUB7 must be plugged in with a 4PIN fan connector.

TIPS

Method of replacing water block logo
The nameplate can be removed by pulling up the middle section of the magnetic nameplate.
*Make sure you start from the middle. @my.valkyrie
@myvalkyrieplays
My Valkyr
@myvalkyrieltd
@myvalkyrie

HW Gaming Solution Ltd
28 Oktovriou 261, View point Tower,
3035 Limassol, Cyprus
info@my-valkyrie.com
www.my-valkyrie.com