Super Sparrow Water Bottle Double Wall Vacuum Insulated Stainless Steel Installation Guide
- June 16, 2024
- Super Sparrow
Table of Contents
Super Sparrow Water Bottle Double Wall Vacuum Insulated Stainless Steel
Installation Guide
Thank you for purchasing Super Sparrow products. Please read the following information carefully before using this product for the first time. If you have any questions about these instructions, please contact us for further instructions. You can send us information through the platform or send an email to service@supersparrow.com Thank you for your purchase and support.
PRECAUTIONS:
-
Before first use, please take out the desiccant inside, soak in warm water or tea for a while, rinse all parts before use. Let all parts dry completely before next use or storage.
-
When the bottle contains hot contents, please keep it out of the reach of children to prevent the bottle from tipping over and causing burns.
WARNING
CHOKING HAZARD
Small Parts Not for children under 3 years -
When using a water bottle to fill ice cubes or carbonated beverages, please do not fill them too full, so as not to overflow or the strong pressure of carbonic acid gas to cause the lid to pop out or leak.
-
Please do not heat it in a microwave oven; do not place it near at sources such as gas stoves, ovens and heaters, so as not to cause discoloration or damage to the bottle.
-
Do not use abrasive cleaners or washing liquids as they may dull or discolor the bottle’s powder-coat finish.
-
Missing, worn or misaligned lid gaskets may cause product to leak, so check periodically to ensure gaskets are correct and in place.
-
Be sure to tighten the cap when not drinking water to prevent the bottle from tipping over and spilling the drink, causing burns or injuries.
-
Before the first use, you need to manually install the straw into the straw cap. Please make sure that the straw is in the correct and firm position, and the silicone tube connecting the straw and the mouth of the bottle is not blocked.
USING INSTRUCTIONS
For maximum thermal efficiency and to keep your drinks hot/cooler longer, preheat or precool the product before initial use:
- Fill the bottle with boiling water, cover the bottle lid and tighten, and let it stand for 5to 10 minutes, then empty the hot water in the bottle, fill the container with the contents, and then cover the lid again to improve thermal efficiency. Never use microwave ovens, conventional ovens or other heat sources for this purpose.
- The same operation method is also used for cold drinks. Fill the bottle with ice water or crushed ice, let it stand for 5 to 10 minutes, pour it out, and then fill it with other drinks.
Be careful not to overfill the
container and leave room at the top of the bottle to screw on the lid to avoid
burns or scalds from spilling hot contents.
Interchangeable Lids:
Standard Stainless Steel Lids
Keep beverages hot for up to 24 hours or hot for up to 12 hours.
Sports Straw Lids
Before the first use, please manually install the straw into the straw cap. If the straw is too long, you can cut it according to the height of the bottle to achieve a suitable length.
When using, please make sure the straw is in the correct and firm position,
and the silicone tube connecting the straw and the mouth of the bottle is not
blocked.
CLEANING INSTRUCTIONS
The contents should not be left in the container for more than 24 hours, please wash the water bottle promptly after each use to prevent odor or mold and keep the product hygienic.
Dishwasher Safe:
Bottles are dishwasher safe for cleaning.
NOTE: The lid and included straw are not dishwasher safe. But be careful not to use harsher detergents (dishwashing detergents with high chlorine or bromide content), so as not to affect the appearance of the product or cause the appearance of the water bottle to age faster.
Hand Wash:
- When washing by hand, it is recommended to wash the bottle with mild detergent and warm water, do not use thinner, bleach.
- It is recommended to use a cleaning sponge to clean the inside of the product. Do not use metal brushes or nylon brushes to prevent scratches on the inner wall.
- If you remove the rubber ring from the bottle cap or remove the straw from the straw cap for a thorough cleaning, make sure the rubber ring or straw is installed correctly and firmly when reassembling.
- It is recommended to use a straw cleaning brush or pipe cleaner to clean the inside of the straw and a sponge bottle brush to clean the bottom of the bottle.
- For solidified rust spots or stubborn water stains caused by impurities in the water, soak overnight in a solution made of warm water and baking soda to remove stubborn stains.
- If you do not use the product for a long time, please wash it thoroughly with clean water and dry it well.
AFTER-SALE INSTRUCTIONS
The material used in our Super Sparrow® insulation is BPA free 18/8 food grade stainless steel. At the same time, our brand supplies original bottle lids. When you need to replace product spare parts, you can contact the Super Sparrow® customer service team by email or purchase them at Super Sparrow® authorized online or offline stores.
If you have any questions about this or other Super Sparrow® products, please send an email to service@supersparrow.com, we will improve and solve your problems wholeheartedly.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>