Super Sparrow ‎WL-17oz-Sage Stainless Steel Water Bottle User Manual

WL-17oz-Sage Stainless Steel Water Bottle

Thank you for purchasing Super Sparrow® products. Please read the following information carefully before using this product for the first time. If you have any questions about these instructions, please contact us for further instructions. You can send us  information through the platform or send an email to service@supersparrow.com.
Thank you for your purchase and support.

PRECAUTIONS:

• Before first use, please take out the desiccant inside, soak in warm water or tea for a while, rinse all parts before use. Let all parts dry completely before next use or storage.
  WARNING
  CHOKING HAZARD
  Small Parts. Not for childern ubder 3 year

• When the bottle contains hot contents, please keep it out of the reach of children to prevent the bottle from tipping over and causing burns.

• When using a water bottle to fill ice cubes or carbonated beverages, please do not fill them too full, so as not to overflow or the strong pressure of carbonic acid gas to cause the lid to pop out or leak.

• Please do not heat it in a microwave oven; do not place it near heat sources such as gas stoves, ovens and heaters, so as not to cause discoloration or damage to the bottle.

• Do not use abrasive cleaners or washing liquids as they may dull or discolor the bottle’s powder-coat finish.

• Missing, worn or misaligned lid gaskets may cause product to leak, so check periodically to ensure gaskets are correct and in place.

• Be sure to tighten the cap when not drinking water to prevent  the bottle from tipping over and spilling the drink, causingburns or injuries.

• Before the first use, you need to manually install the straw into the straw cap.Please make sure that the straw is in the correct and firm position, and the silicone tube connecting the straw and the mouth of the bottle is not blocked.

USING INSTRUCTIONS

For maximum thermal efficiency and to keep your drinks hot/cooler longer, preheat or precool the product before initial use:

1. Fill the bottle with boiling water, cover the bottle lid and tighten, and let it stand for 5 to 10 minutes, then empty the hot water in the bottle, fill the container with the contents, and then cover the lid again to improve thermal efficiency. Never use microwave ovens, conventional ovens or other heat sources for this purpose.
2. The same operation method is also used for cold drinks. Fill the bottle with ice water or crushed ice, let it stand for 5 to 10 minutes, pour it out, and then fill it with other drinks.
   Be careful not to overfill the container and leave room at the top of the bottle to screw on the lid to avoid burns or scalds from spilling hot contents.

2 Interchangeable Lids:

Wide Mouth Stainless Steel Lids
Hot drinks for up to 8 hours, and cold drinks for up to 24 hours.

Straw Lids
Before the first use, please manually install the straw into the straw cap. If the straw is too long, you can cut it according to the height of the bottle to achieve a suitable length.
When using, please make sure the straw is in the correct and firm position, and the silicone tube connecting the straw and the mouth of the bottle is not blocked.
If the bottle Is filled with hot or carbonated drinks above 70°C and the straw lid Is used, please follow the steps below to use the product correctly to avoid Injury:

1. Before drinking, please stand the bottle upright away from the face, turn it up and open the stra w lid nozzle.
2. Wait for 1-2 seconds to release the hot steam or carbonic acid gas inside the bottle.
3. After the hot steam accumulated in the bottle is released, slowly sip through the straw.

PLEASE NOTE:
if it is a hot drink, be sure to test the temperature of the contents before drinking, however, in general, when the bottle is filled with hot contents, we recommend not to use a straw lid to avoid scalding caused by too hot drinks.

CLEANING INSTRUCTIONS

The contents should not be left in the container for more than 24 hours, please wash the water bottle promptly after each use to prevent odor or mold and keep the product hygienic.

Dishwasher Safe:
Both the bottle and lid are dishwasher safe. (Note: The included straw is not recommended for washing in the dishwasher.)
At the same time, please be careful not to use more harsh detergents (dishwashing detergents with high chlorine or bromide content), so as not to affect the appearance of the product, causing the appearance of the water bottle to age or fade faster.

Hand Wash:

• When washing by hand, it is recommended to wash the bottle with mild detergent and warm water, do not use thinner, bleach.
• It is recommended to use a cleaning sponge to clean the inside of the product. Do not use metal brushes or nylon brushes to prevent scratches on the inner wall.
• If you remove the rubber ring on the straw lid or remove the straw from the straw lid for a thorough cleaning, make sure the rubber ring and straw fit properly and securely when reassembling.
• It is recommended to use a straw cleaning brush or pipe cleaner to clean the inside of the straw and a sponge bottle brush to clean the bottom of the bottle.
• For solidified rust spots or stubborn water stains caused by impurities in the water, soak overnight in a solution made of warm water and baking soda to remove stubborn stains.
• If you do not use the product for a long time, please wash it thoroughly with clean water and dry it well.

AFTER-SALE INSTRUCTIONS

The material used in our Super Sparrow® insulation is BPA free 18/8 food grade stainless steel.
At the same time, our brand supplies original bottle lids. When you need to replace product spare parts, you can contact the Super Sparrow® customer service team by email or purchase them at Super Sparrow® authorized online or offline stores.
If you have any questions about this or other Super Sparrow® products, please send an email to service@supersparrow.com, we will improve and solve your problems wholeheartedly.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>