JAFANOA JF999 Air Purifier User Manual
- June 16, 2024
- JAFANOA
Table of Contents
- Packing Contents
- Specifications
- Safety Instruction
- KNOW YOUR AIR PURIFIER
- Control Panel
- Product Features
- Using Your Air Purifier
- Operating Instruction
- Sensor Replacement
- Cleaning and Maintenance
- Filter replacement
- Warranty
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
JAFANOA JF999 Air Purifier User Manual
Packing Contents
JF999 Air purifier | 1 set |
---|---|
Composite filter | 2 pieces (Preinstalled) |
Power Cord | 1 (in the accessories box) |
User Manual | 1 (in the accessories box) |
Specifications
Product specifications
Product name | Air Purifier | Model | JF999 |
---|---|---|---|
Rated Voltage | 120V~ | Product Size | 13.0 x 11.81x 28.03 in /33.0x 30.0 x71.2cm |
Rated Frequency | 60Hz | Package Size | 13.0 x 11.81x 28.03 in /33.0x 30.0 |
x71.2cm
Rated Current| 1.4A| 16.3 x 15.08x 31.93 in /41.4x 38.3 x81.1cm
Rated Power| 110W| N.W| 27.1lb/12.3kg
CADR (Clean Air Delivery Rate)| 588CFM(1000m³/h| G.W| 32.61lb/14.
Noise Level| 22-58d| Standby Po| < 2W
Operating Conditions| Temperature: 14℉-104℉/-10℃-40℃
Humidity20%-95% RH| Filte| 3000
Room Area Served| 915ft (5 Times/h 2 )
Safety Instruction
The following safety precautions and instructions must be read carefully and observed when the product is used!
Prohibitory sign| The behaviors with this sign must be prohibited, otherwise
it may cause product damage or endanger the user’s personal safety.
---|---
Warning sign| The behaviors with this sign must be operated in strict
accordance with the requirements, otherwise it may cause product damage or
endanger the user’s personal safety.
Attention sign| The behaviors with this sign must be paid attention to,
otherwise it may cause product damage or other losses due to improper
operation.
| Please do not touch the power plug with wet hands.
Please do not block the air inlet/outlet.
Please do not use the machine in any place with much oil fume or high
humidity.
| Please do not rinse the high-efficiency composite filter with water.
This machine shall not be used by people with disabilities, perceptual
disturbance or dysgnosia or children alone, unless they use it under the
supervision and guidance of safety director on the site.
| Please regularly clean the machine and power plug.
Only the 120V power sockets are 120V power sockets.
Please do not put it close to or on any heatsource (such as a fireplace, stove
or a place with flammable gases).
Please be careful when cleaning the air purifier, as corrosive detergents may
damage the surface.
Please do not unplug the power cord from the power socket when cleaning the
air purifier or leaving it unused. Otherwise, it may cause electric shock due
to poor insulation or fire due to short circuit.
KNOW YOUR AIR PURIFIER
Structure and Name of Product Components
- Filter cover
- Composite filter
- Main unit
- Control Panel
- Display
If the picture is inconsistent with the actual product, the latter shall prevail.
Display
Control Panel
Icons | Icons Name | Introduction |
---|---|---|
On/Off | Turns the Air Purifier ON or OFF. | |
Fan Speed | Fan speed cycles through 1~5 setting. | |
Filter Reset | The filter needs to be changed when the icon lights up in red. | |
Light | Press dimmer to adjust the lighting mode of the ambient light. | |
WiFi | Press WiFi button to connect it to WiFi. | |
Auto | In Auto mode, fan speed will be adjusted automatically based on the |
real-time PM2.5 density.
| Timer| Set the timer to switch on and off the air purifier automatically.
The timer is available from 1 to 12 hours, stopping operation when the
selected time has elapsed.
| Sleep| Press the sleep button in the working state to enter the sleep mode.
| Child Lock| All the other buttons on the control panel are not responsive
when the child lock is o
Product Features
Integration of Multiple Functions
- Efficiently purify PM2.5, smoke, pollen, dust and other particulate pollutants
- 5 fan speeds
- Timer (0-12H)
- Filter replacement indicator
- Manual, Auto, Sleep and other operating modes
- Real-time monitoring of indoor temperature and humidity
- Child lock
- Real-time value display of PM2.5
- WiFi control
3-Stage Filtration
Pre-filter: Captures larger particles such as human hair, fibers, pet
fur, and dust particles;
Protects th HEPA filter and extends its life
HEPA filter: Captures and filters airborne contaminants down to 0.01
microns in size, such
as PM2.5, dust, smoke particles, mold spores, plant spores, and pollen
activated carbon filter: Absorbs and eliminates fumes and volatile organic compounds in the air.
Using Your Air Purifier
Precautions for Use
- All filters are attached in the air purifier.
- Please ensure that the filter is installed correctly before use.
-
Pull the filter cover out slightly.
-
Take out the filter cover.
-
Take out the new filter with plastic film of the machine inside.
-
Remove the plastic film on the filter.
-
Put the filter without plastic film back into the machine.
-
Put the filter mesh cover back.
Getting Started
-
Insert the power plug to make the machine powered on, and the buzzer makes a “ding” sound.
-
Power on by touching the power key.
-
The display screen lights up and touch a relevant function button to enter the working state.
Operating Instruction
On/off button
Touch the button “ ” in the standby state to enter the working state; touch the key “ ” in the working state to enter the standby state. The power key indicator lights up in red in the standby state and white in the working state.
Sleep button
Touch the button “ ” in the working state to enter the sleep mode. In the sleep mode, all indicator lights and icons light off except for the “ ” indicator light and sleep icon. The wind speed remains at Gear 1, and the sleep button indicator light and icon will light off in 10 seconds. The air purifier will be awakened in the sleep mode by touching any function key once. The sleep button indicator light and icon will light up when it returns to the sleep mode. Exit the sleep mode and return to the pre-sleep setting mode by touching any function button once again.
Light button
Touch “ ”to adjust the light brightness. Each touch will change the ambient light mode. 5 modes to choose:
- 25% brightness
- 50% brightness
- 100% brightness
- shut off button, display screen and ambient light. 10s later, the sleep icon light off
- lit button and display screen , ambient light stays off
When the touch panel is completely black, press any key to wake up “ ”
Memory function
Restart the device in the power-up state every time, the machine will remember the previous wind speed and light settings. However, after the adapter is re- plugged, everything will return to the default state. The machine runs at Gear 1 by default after startup, and the ambient light will be slowly on and then go out.
WiFi button
When the machine is powered on and enters the standby state, the WiFi button and icon flash for network connection. The WiFi button and icon will be constantly on when network is connected but go out if network connection fails within 10 minutes.
When the WiFi button and icon go out in the power-on state, press and hold the WiFi button for 3 seconds to connect the network. The prompt tone “ding ding ding” will be heard, and the WiFi button and icon flash for network connection. The WiFi icon flashes in the process of network connection and keeps constantly on when the network is successfully connected. The icon will go out when the network fails to be successfully connected within 10 minutes.
Fan speed button
Touch the fan speed button + in the working state to increase the fan speed, and touch the fan speed button – to decrease the fan speed.
The white indicator light of the fan speed key is on. Each touch of the button will change the gear from 1 to 5 successively and circularly. When the fan speed is adjusted, the fan speed gear is displayed in the comprehensive display area.
Timer button
Press “ ”, the timer button light will turn ON to set the timer. The screen will display the timer’s set time. Each touch will increase the timer by 1 hour, the value range is 0-12. When the value is 0, the timing can be canceled.
Release the button and after 3 seconds the timer will be set. The timer will then start counting down.
Press “ ” in the working state to set timed shutdown;
Press “ ” in the standby state to set timed s
Child lock button
This button aims to avoid misoperation by children or pets in an unattended condition.
In the working state, press and hold the button “ ”(for more than 3s) to switch the on/off state of child lock. When the child lock is on, the child lock key indicator and icon on the display screen light up. Other function button become invalid when the child lock is on. When the child lock is off, the child lock key indicator lights up.
Auto button
Touch the button “ ” in the working state to enter the auto mode, the auto button is fully on.
The wind speed of the machine changes with the PM2.5 concentration value, and the wind speed gear is switched from 1 to 4 automatically.
The color of the air quality indicator also changes with the PM2.5 concentration value (the corresponding relation is shown in the following figure).
PM2.5 value| Air quality| PM2.5 air quality indicator| Wind
speed gear
---|---|---|---
0-12| Excellent| Green| 1
13-35| Good| Blue| 2
36-55| Poor| Yellow| 3
>55| Severe| Red| 4
Sensor Replacement
Replacement of Sensors (Please do not operate by yourself because the sensors must be replaced by professional maintenance personnel)
-
Open the sensor cover with a straight screwdriver.
-
Remove the sensor cover.
-
Hold on the hardware handle and pull out the sensor module
-
Unplug the terminal block from the old sensor module and replace it into a new sensor module.
-
Put back the sensor module and close the sensor cover.
Cleaning and Maintenance
Cleaning and Maintenance
Please unplug the power plug from the adapter before machine maintenance.
-
Clean the machine body (cleaning once a month is recommended):
-
Wipe off stains with a soft rag
-
Wipe off stubbom stains with a soft rag dipped with proper amount of neutral detergent.
Note: Please avoid scratching the machine shell with any hard object during maintenance, Please operate according to the manual and avoid damaging any machine part during base disassembly. -
Clean and change the filter (once operation every 3-6 months is recommended):
Clean and change the filter (once operation every 3-6 months is recommended):
-
The replacement of filter will be reminded by the built-in program. The filter can also be replaced according to the service life prompt of filter. It can also be replaced in real time through the filter life reset function.
The filter life is set as 3000 hours. The filter life indicators go off by one for every 600 hours of life used. When the rest filter life is less than 150 hours, the filter life reset key lights up in red and the last indicator keeps flashing (1Hz), prompting that the filter mesh needs to be replaced before the filter life is resel Reset of filter life When the rest filter life is not less than 150 hours, it can’t be reset by touching the filter life reset key (for more than 3s) but only makes a prompt tone “ding”. When the rest filter life is less than 150 hours, the filter life reset key flashes, in this case, the filter life can be reset by touching the reset key (for more than 3s) and makes a prompt tone “ding”. The filter life indicators are fully on when the parameter is successfully reset
Forcible reset of filter life:
Press and hold the filter reset key (for more than 3s) within 30s of power-on state in the standby mode, the filter life will be reset forcibly and make a prompt tone “ding”. The screen will flash (2 times/s) 6 times, which indicates the completion of for ciblereset. After the machine is restarted, all the filter life indicators will be fully on -
The vacuum cleaner can be used to clean the deposited dust on the surface of the composite filter mesh to prolong the service life of filter mesh (it is recommended to clean it once every other month and do not wash with water).
The service life of filter mesh may vary with different environments for using
the machine. For example, it will be shortened in smoking areas and areas with
pets. Please replace the filter mesh in time when the purification effect
becomes worse.
“Please dispose the used waste filter mesh according to the relevant regulations on solid waste.
Filter replacement
-
When the reset button of filter life lights up in red and the last indicator begins to flash, it prompts that the filter needs to be replaced.
-
Touch the on-off button to power off, and unplug the machine.
-
Pull the filter cover out slightly.
-
Take out the filter cover.
-
Take out the failed filter in the machine
-
Remove the plastic film from the new filter.
-
Reinstall the new filter in the machine.
-
Put the filter cover back
-
Plug in and touch the on-off button.
Warranty
Warranty Information
The products of Jafanda have a warranty period of 1 year from the date of purchase. In addition, Jafanda guarantees that all the products are made from top-quality materials, and you can enjoy excellent technology and service from the date of purchase to the end of the warranty period.
Jafanda will replace the defective products caused by manufacturing technique with qualified products, or the customers can apply for a refund within 30 days from the date of purchase. Limited warranty only applies to the case of installation, use and maintenance of the air purifier in accordance with this manual.
One-year warranty extension:
Register your product at www.jafanda.com/pages/warranty
Your warranty period will be extended for an additional one year Please fill
in all required fields, including your order ID, place of purchase and date of
purchase (if applicable)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>