tp-link TL-SG1005P-PD 5-Port Gigabit Desktop PoE Switch Installation Guide

tp-link TL-SG1005P-PD 5-Port Gigabit Desktop PoE Switch Installation Guide

LED Explanation

Power

On: Power on
Off: Power of

PoE MAX

On: The remaining PoE power is ≤ 7 W
Off: The remaining PoE power is > 7 W

PoE in Status

On (Green): Powered by 802.3bt (type 4)
On (Yellow): Powered by 802.3bt (type 3)
Off: Powered by 802.3af/at

Link/Act and PoE Status

On (Green) : Connected to a 1000 Mbps device

On (Yellow ): Connected to a 10/100 Mbps device

Flashing : Transmitting/receiving data

Off: No device is connected to the corresponding port

On: Providing PoE power

Flashing: PoE fault/Short-circuit

Off: Not providing PoE power

Switches Explanation

Note: The numbers in brackets indicate the ports where the feature takes effect. For example, when Extend (Port 1-2) is toggled to On, the Extend mode will be enabled for ports 1-2.

Extend

Off: The corresponding ports run at 10/100/1000 Mbps and support PoE power supply up to 100 m
away.
On: The corresponding ports run at 10 Mbps and support PoE power supply up to 250 m away

Recovery

Off: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD). When the switch finds that the PD works abnormally, the switch will reboot it.

Connection

Note :

1. TL-SG1005P-PD does not support DC or AC power input. A PoE Power Sourcing Equipment (PSE)
   needs to be connected to the PoE IN port to provide power for TL-SG1005P-PD.

2. The PoE OUT ports can also be connected to non-PoE devices, but only transmit data.

Specifications

Standard| IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3x, IEEE802.3af, IEEE802.3at, (For PoE IN Port only) IEEE802.3bt
---|---
Protocol| CSMA/CD
Switching Capacity| 10 Gbps
Transfer Method| Store-and-Forward
MAC Address Learning| Automatically learning, automatically aging
Interface| 5 10/100/1000 Mbps RJ45 Ports Auto-Negotiation MDI/MDIX PoE IN Port: Port 5 PoE OUT Ports: Port 1-4
Network Media (Cable)| UTP/STP of Cat. 5E or above (based on the standards that the connected devices comply with)
PoE INPUT| Compliance with 802.3af/at/bt
PoE OUTPUT| Compliance with 802.3af/at
PoE Budget (for different PoE INPUT types*)| 802.3af (type 1): 9W 802.3at (type 2): 21W 802.3bt (type 3): 47W 802.3bt (type 4): 66W
Wall Mountable| Yes
Distance Between Mounting Holes| 94 mm

PoE budget calculations are based on laboratory testing. Actual PoE power budget is not guaranteed and may vary due to PoE input, client limitations and environmental factors.

Environmental and Physical Specifications

Operating  Temperature: -30˚C to 70˚C (-22˚F to 158˚F)
Storage Temperature: -40˚C to 70˚C (-40˚F to 158˚F)
Operating Humidity: 10% to 90%RH non-condensing
Storage Humidity: 5% to 90%RH non-condensing

Frequently Asked Questions (FAQ)

Q1. Why is the Power LED not lit?

The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please try the following: A1: Make sure the PSE and PD devices are connected to the corresponding ports properly. A2: Make sure the PSE device is powered on and works normally

Q2. Why is the Link/Act LED not lit while a device is connected to the

corresponding port?

It is recommended that you check the following items: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and works normally. A3: The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled, it should be less than 250 meters (820 feet).

Q3. Why are PoE ports not supplying power for PoE devices?

When the total power consumption of connected PoE devices exceeds the maximum, the PoE OUT port with a smaller port number has higher priority. The system will cut off power to the ports with larger port numbers to ensure supplying to other ports. For example. if the switch is powered by 802.3bt (type 4) with port 1, 2 and 4 consuming 15.4 W respectively, and an additional PoE device with 20 W is connected to port 3, the system will cut off the power of port 4 to compensate for the overload.

Q4. What should I notice before using the PoE Auto Recovery feature?

A1: Before upgrading a connected PD device, disable PoE Auto Recovery to avoid damage to the PD device. A2: When a PD device does not send data packets to the switch for a long period in certain scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD device repeatedly rebooting.

To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community.

For technical support and other information, please visit https://www.tp- link.com/support, or simply scan the QR code.

Safety Information

• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• This product can be powered only by power supplies that comply with Power Source Class 2 (PS2) or Limited Power Source(LPS) of IEC 62368-1.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp- link.com/en/ce

UK Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.

The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca

References

• TP-Link Community
• CE Regulatory Compliance | TP-Link
• Regulatory Compliance | TP-Link

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>