ZAGiO BYCZ565 Cold Hot Normal Top Loading Water Dispenser Instruction Manual
- June 16, 2024
- ZAGiO
Table of Contents
INSTRUCTION & MAINTENANCE MANUAL
Cold-Hot-Normal Top Loading
Water Dispenser with Ice Maker
SKU No. 60395116
Series No. BYCZ565
Please read the use specification carefully before you use this product and
let the use specification be well placed.
Important safety instructions
When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property, read all instructions before using any appliance.
- Do not let hot water touch bare skin. Keep combustible material such as furniture, bedding, pillows, clothes, and/or paper away from the back of the unit.
- Do not operate this, or any other appliance, with a damaged power cord. No other appliance should be lugged into the same outlet. Be sure that the plug is fully inserted into the outlet.
- Do not run the power cord over carpet or other heat insulations. Do not cover the cord. Keep the cord away from high traffic areas, and do not submerge in water.
- We do not recommend the use of extension cord as it may overheat and cause a risk of fire
- Exercise caution and use reasonable supervision when the appliance is used by or near children.
- Do not use your water dispenser outdoors. Place the water dispenser away from direct sunlight and make sure that there is at least 4 inches(lOcm) of space between the back of your unit and wall. Keep a minimum of 2 inches (5cm) on each side of your unit free.
- Do not use this product to dispense anything other than water
- To avoid a hazard due to instability of the appliance, it must be placed on an even and flat surface.
- If the supply cord is damaged, the manufacturer or its service agent or a similarly qualified person must replace it in order to avoid a hazard.
- This water cooler must be positioned so that the plug is accessible.
- Disconnect the plug from the outlet when not in use.
- Remove power plug or disconnect from the main power source before servicing the appliance.
| MODEL | BYCZ565 |
|---|---|
| CLIMATE | ST |
| VOLTAGE/FREQUENCY | 220-240V-50Hz |
| HEATING POWER | 500W |
| ICE MAKING POWER | 120W |
| COOLING CURRENT | l.5A |
| HEATING CAPACITY | >90€ 5L/h |
| COOLING CAPACITY | <10C 3L/h |
| ICE CAPACITY | 13kg/24h |
| REFRIGERANT/VOLUME | Rl34a/72g |
| NET WEIGHT | 18kg |
| TEST | WATER TEMP 25C |
ENVIRONMENT TEMP25C
Circuit diagram
Control Panel
Operating instructions
Standby
After the machine is powered on, the buzzer will beep once, the power
indicator will be on, and the machine will enter standby.
Hot water function
Press the heating touch, the buzzer will beep once, turn on the hot water
function, and the hot water indicator will flash; when the water temperature
reaches the set requirement, the hot water indicator will be on; if you need
to turn off the hot water function, press the heating touch again, the hot
water indicator will go out, and the hot water function will be turned off.
Cold water function
Press the cooling touch, the buzzer will beep once, turn on the cold water
function, and the cold water indicator will flash; when the water temperature
reaches the set requirement, the cold water indicator will be on; if you need
to turn off the cold water function, press the cooling touch again, the cold
water indicator will go out, and the cold water function will be turned off.
Ice-making function
Press the ice-making touch, the buzzer will beep once, the ice-making
indicator flashes, the ice making function is on, and the ice-making time is
about 10 minutes per cycle. When the ice-making indicator is always on, it
means the refrigerator is full, ice making is suspended; remove the ice cubes
in the box, and the machine restarts the ice-making function; if you need to
turn off the ice-making function, press the ice making touch, the ice-making
indicator will go out and the ice-making function will be turned off.
Note: Before the ice-making function starts, please make sure that the
water level in ice storage tank does not exceed the baffle. If it does, please
release water from the ice storage sewage outlet.
Troubleshooting
| Fault phenomenon | Fault cause | Fault treatment |
|---|
The fault indicator is on, and
the hot water indicator flashes quickly.| Hot water temperature
sensor short circuit or open circuit.| Contact soles service.
The fault indicator is on, and
the cold-water indicator flashes quickly.| Cold water temperature
sensor short circuit or open circuit.| Contact sales service.
The fault indicator is on, and the ice making indicator flashes quickly.|
Ambient temperature sensor short circuit or open circuit.| Contact sales
service.
The fault indicator is on, the ice box is stuck and cannot be turned over, the
ice cubes are connected.| The ice evaporator position is too low.| Position
up.
Ice making cycle time is too long.| Turn on the machine after 15 minutes of
shutdown.
Warm water temp is too high.| Leaking bucket, Water level is too high| Replace
the bucket.
The ice making process is normal, but no ice is formed.| Ambient temperature
or water temperature is too high.| Please make ice when the ambient
temperature is below 32°C.
The fault indicator flashes quickly and the ice making indicator goes out.|
Ice-making lack of water| Replace the bucket with water.
No ice. no cooling water| Leaking or clogged refrigeration system| Contact
sales service