TANNOY VX Series Dual Full Range Loudspeaker User Guide

TANNOY VX Series Dual Full Range Loudspeaker

Product Information

Specifications

• Product Name: VX Series
• Models: VX 15Q (-WH)/VX 15HP (-WH)/VX 12.2Q (-WH)/VX 12Q (-WH)/VX 12HP (-WH)/VX 12 (-WH)/VX 8M/VX 8.2 (-WH)/VX 8 (-WH)/VX 6 (-WH)/VX 5.2 (-WH)
• Type: Power Dual Full Range Loudspeaker with Q-Centric Waveguide/Low-Frequency Driver
• Applications: Portable and Installation

Product Usage Instructions

Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Use only attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or solder with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Do not install in a confined space, such as a bookcase or similar unit.
12. Do not place naked flame sources, such as lighted candles, on the apparatus.

Security instructions

1. Lisaz ces consignes.
2. Conserve these consignments.
3. Respect all avertissements.
4. Respect all instructions for use.
5. Nettoyez l’appareil has dry chiffon.

Important health instructions

1. Leggere quest this istruzioni.
2. Conserve this instruction.
3. Pay attention to everything you see.
4. Apply all instructions.
5. Do not use this device near the water.
6. Pulse exclusively with a dry cloth.
7. Do not install near a heat source such as a radiator, thermoregulator, stufe or other appliances (including amplifiers) that produce heat.
8. Use exclusively a device/accessory specific to the product.
9. Utilizzare solo carrelli, supporti, treppiedi, staffe o tavoli indicati dal produttore o venduti con l’apparecchio. Using a carrello, pay attention when asked to the carrello/apparecchio combination to avoid being injured in the spotlight.
10. Noninstallare in a ristretto space, come in a library or in a similar structure.
11. Don’t collocate the device’s fonti di fiamme liberate, as it can be accessed.

Belangrijke veiligheidsvoorschriften
Lees ten voorschriften.

FAQ

• Q: Can I use the VX Series near water?
  A: No, it is not recommended to use the VX Series near water to prevent any damage or accidents.

• Q: How should I clean the VX Series?
  A: Clean the VX Series only with a dry cloth to avoid any moisture-related issues.

• Q: Can I place naked flame sources on the VX Series?
  A: No, do not place any naked flame sources, such as lit candles, on the VX Series to prevent fire hazards.

VX Series

• VX 15Q (-WH)/VX 15HP (-WH)/VX 12.2Q (-WH)/VX 12Q (-WH)/VX 12HP (-WH)
  15/12″ Power Dual Full Range Loudspeaker with Q-Centric Waveguide/Low- Frequency Driver for Portable and Installation Applications

• VX 12 (-WH)/VX 8M/VX 8.2 (-WH)/VX 8 (-WH)/VX 6 (-WH)/VX 5.2 (-WH)
  12/8/6/5″ Dual Concentric Full Range Loudspeaker with Low-Frequency Driver for Portable and Installation Applications

Safety Instruction

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Use only attachments/accessories specified by the manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office or your household waste collection service.
12. Do not install in a confined space, such as a bookcase or similar unit.
13. Do not place naked flame sources, such as lighted candles, on the apparatus.

Thank you for choosing a Tannoy loudspeaker product for your application. If you would like further information about this or any other Tannoy product, please visit our website at tannoy.com.

Unpacking the Loudspeaker

Each Tannoy VX Series loudspeaker is carefully tested and inspected prior to shipment. After unpacking, please inspect for any exterior physical damage, and save the carton and any relevant packaging materials in case the loudspeaker again requires packing and shipping. In the event that damage has been sustained in transit notify your dealer and the shipping carrier immediately.

System Requirements

System Requirements – Passive and Bi-amped Loudspeakers
Within the VX Series, system designers can choose from a variety of sizes, power levels, and coverage patterns to suit particular requirements. For extended bass performance, models with the “.2” designation augment the Dual Concentric LF driver with a second matched LF driver. The “HP” designation indicates extended power handling capabilities, while the “Q” suffix indicates incorporation on the new Q-Centric WaveguideTM (QCW™) for applications requiring an asymmetrical coverage pattern. The QCW horn can be rotated in a matter of minutes, allowing placement of the 75 x 40-degree pattern with either horizontal or vertical orientation.

• VX “HP” and “Q” versions have switchable inputs to allow operation in passive or bi-amp modes.
• All other VX versions are full-range speakers operating as a passive system and require only one amplifier channel.

To avoid wasting amplifier power, you should use heavy-duty speaker cable, with a minimum wire size of 1.5 mm² (16 AWG), and preferably 2.5 mm² (14 AWG) for longer runs. Use larger wire sizes for speakers wired in parallel. For extreme cable lengths, be aware of cable impedance and resistive losses. Always observe the correct polarity.

WARNING:
VX Series loudspeakers can produce high sustained output levels for long periods of time. If users are in close proximity, these levels could lead to permanent hearing damage. Because Tannoy loudspeakers have a natural-sounding, flat frequency response and very low distortion, users may not be aware of the potential hazard. For continuous exposure to high levels, we recommend the use of a sound level meter to ensure noise levels are within safety limits. The meter should be capable of integrating levels over a period of exposure in conformance with noise control standards.

Amplifier Considerations

The VX series loudspeakers are optimized for use with the Lab Gruppen PLM+ series amplifiers or Lake LM series controllers used in combination with Lab Gruppen FP amplifiers. A full range of DSP settings to suit any configuration are provided for download on the Tannoy website. The use of third-party amplification and processing is only advised using the matrix of manual settings as well as the limiter calculator provided on the Tannoy website. VX series loudspeaker enclosures should be driven by high-quality power amplifiers designed for true professional use. Power amplifiers should be capable of delivering long term broadband power equal to half the loudspeaker’s peak power rating at its stated nominal impedance. The use of underpowered amplifiers must be avoided as heavily clipped signals can cause permanent loudspeaker damage. Limiters, crossovers and equalization points must be set in accordance with the settings provided on the Tannoy website. This will ensure the optimum sound quality and long-term reliability as well as protection from damage.

Neutrik speakON NL4 locking input connector(s) are provided, allowing options for input and link, passive, and bi-amp operation.

Recommended Amplifier Power

Model| VX 5.2| VX 6| VX 8| VX 8.2| VX 8M| VX 12| VX 12HP / VX 12Q| VX 12.2Q| VX 15HP / VX 15Q
---|---|---|---|---|---|---|---|---|---
Mode| Passive| Passive| Passive| Passive| Passive| Passive| Passive| Bi- amp LF| Bi-amp HF| Passive| Bi-amp LF| Bi-amp MHF| Passive| Bi-amp LF| Bi-amp HF
Impedance| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω| 8 Ω
Minimum Amplifier Power| Continuous RMS| 130 W| 100 W| 130 W| 200 W| 130 W| 200 W| 350 W| 350 W| 80 W| 500 W| 350 W| 350 W| 400 W| 400 W| 80 W
Peak| 520 W| 400 W| 520 W| 800 W| 520 W| 800 W| 1400 W| 1400 W| 800 W| 2000 W| 1400 W| 1400 W| 1600 W| 1600 W| 800 W

Connections

VX 5.2, VX 6, VX 8, VX 8.2

VX 8M

VX 12

VX 12HP, VX 12Q, VX 12.2Q, VX 15HP, VX 15Q

Mounting and Fixing

Arraying
Small alterations to loudspeaker positions can have the effect of minimizing problematic combing frequencies. Arrays should be constructed so that the individual coverage patterns of each loudspeaker combine with minimal overlap. The design of the VXP cabinet greatly simplifies the creation of effective arrays, allowing seamless wide horizontal coverage using two loudspeakers without the need for tedious experimentation.

By placing the VXP cabinets with the 30-degree angled rear panels together, minimal dispersion pattern overlap is achieved, guaranteeing an extraordinarily smooth transition. In many applications, the 90 or 75-degree dispersion pattern may be sufficient in the horizontal plane. It is also possible to stack the cabinets vertically using the above method (in a central cluster for example) where greater vertical dispersion is required. As shown in the above diagram, one of the VXP cabinets is inverted to allow the optimum splay angle to be achieved. The grille can be simply removed from this cabinet and replaced for matching orientation. The grille is held in position by the two fixing screws on the top and bottom lips of the cabinet.

• The Tannoy Professional hardware covered in this guide has been designed to offer quick, simple, cost-effective, and secure solutions for mounting specific Tannoy Professional loudspeakers. This hardware has been designed and manufactured with a high safety load factor for its specific role. To ensure the safest possible use of the hardware covered in this guide, it must be assembled in strict accordance with the instructions specified. The information in this
• Quick Start Guide relating to the assembly and the safe use of these accessories must be understood and followed.
• IMPORTANT NOTE: The mounting of a permanently installed sound system may be dangerous unless undertaken by qualified personnel with the required experience and certification to perform the necessary tasks. Walls, floors or ceilings must be capable of safely and securely supporting the actual load. The mounting accessory used must be safely and securely fixed both to the loudspeaker and to the wall, floor or ceiling.
• When mounting rigging components on walls, floors or ceilings, ensure that all fixings and fasteners used are of an appropriate size and load rating. Wall and ceiling claddings, and the construction and composition of walls and ceilings, all need to be taken into account when determining whether a particular fixing arrangement can be safely employed for a particular load. Cavity plugs or other specialist fixings, if required, must be of an appropriate type, and must be fitted and used in accordance with the maker’s instructions.
• The operation of your speaker cabinet as part of a flown system, if installed incorrectly and improperly, can potentially expose persons to serious health risks and even death. In addition, please ensure that electrical, mechanical and acoustic considerations are discussed with qualified and certified (by local state or national authorities) personnel prior to any installation or flying.
• Make sure that speaker cabinets are set up and flown by qualified and certified personnel only, using dedicated equipment and original parts and components delivered with the unit. If any parts or components are missing please contact your Dealer before attempting to set up the system.
• Be sure to observe the local, state and other safety regulations applicable in your country. MUSIC Tribe, including the MUSIC Tribe companies listed on the enclosed “Service Information Sheet”, assumes no liability for any damage or personal injury resulting from improper use, installation or operation of the product. Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure and stable condition. Make sure that, where the speaker is flown, the area underneath the speaker is free of human traffic. Do not fly the speaker in areas that can be entered or used by members of the public.
• Speakers create a magnetic field, even if not in operation. Therefore, please keep all materials that can be affected by such fields (discs, computers, monitors, etc.) at a safe distance. A safe distance is usually between 1 and 2 metres.

Technical Specifications

 | VX 5.2 (-WH)| VX 6 (-WH)| VX 8 (-WH)| VX 8M
---|---|---|---|---
System|  |  |
Frequency response| 87 Hz – 35 kHz ±3 dB

65 Hz – 45 kHz -10 dB

| 92 Hz – 35 kHz ±3 dB

80 Hz – 45 kHz -10 dB

| 85 Hz – 35 kHz ±3 dB

62 Hz – 45 kHz -10 dB

| 85 Hz – 35 kHz ±3 dB

62 Hz – 45 kHz -10 dB

Nominal dispersion| 120° H x 90° V @ -6 dB points| 90° conical @ -6 dB point| 90° conical @ -6 dB point| 90° conical @ -6 dB point
Directivity factor (Q)| 7.3| 5.6| 6.8| 6.8
Directivity index (DI)| 8.6| 7| 7.9| 9.2
Power handling (IEC)

Passive Bi-amp

|

130 W continuous, 520 W peak

–

|

100 W continuous, 400 W peak

–

|

130 W continuous, 520 W peak

–

|

130 W continuous, 520 W peak

–

Sensitivity| 90 dB (1 W @ 1 m)| 91 dB (1 W @ 1 m)| 92 dB (1 W @ 1 m)| 92 dB (1 W @ 1 m)
Maximum SPL

Passive Bi-amp

|

111 dB continuous, 117 dB peak

–

|

111 dB continuous, 117 dB peak

–

|

113 dB continuous, 119 dB peak

–

|

113 dB continuous, 119 dB peak

–

Impedance Passive Bi-amp|

8 Ω

–

|

8 Ω

–

|

8 Ω

–

|

8 Ω

–

Crossover Type| Passive with dynamic HF protection| Passive with dynamic HF protection| Passive with dynamic HF protection| Passive with dynamic HF protection
Components| 1 x 5″ (125 mm) LF driver

1 x 5″ (125 mm) constant directivity Dual Concentric

| 1 x 6″ (150 mm) constant directivity Dual Concentric| 1 x 8″ (200 mm) constant directivity Dual Concentric| 1 x 8″ (200 mm) constant directivity Dual Concentric
Enclosure
Connectors| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2 x Neutrik speakON NL4
Wiring

Passive Bi-Amp

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

–

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

–

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

–

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

–

Dimensions (H x W x D)| 334 x 181 x 201 mm

(13.1 x 7.1 x 7.9″)

| 334 x 226 x 216 mm

(13.1 x 8.9 x 8.5″)

| 389 x 281 x 276 mm

(15.3 x 11.1 x 10.9″)

| 389 x 281 x 316.7 mm

(15.3 x 11.1 x 12.5″)

Net weight| 4.4 kg (9.7 lbs)| 5.0 kg (11.0 lbs)| 8.1 kg (17.8 lbs)| 8.6 kg (18.9 lbs)
Construction| 12 mm (1/2″) plywood, vented and internally braced| 12 mm (1/2″) plywood, vented and internally braced| 15 mm (5/8″) plywood, vented and internally braced| 15 mm (5/8″) plywood, vented and internally braced
Finish| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi-matt black paint
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M6 x 2 yoke bracket insert (4 mm Allen key)

M6 x 4 inserts Compatible with industry-standard brackets

| M6 x 2 yoke bracket insert (4 mm allen key)

M6 x 4 inserts Compatible with industry-standard brackets

Blanking plate for optional VTH pole mount

| M10 x 2 yoke bracket insert (6 mm Allen key)

M10 x 2 flying inserts Compatible with industry-standard brackets

M6 x 4 inserts Blanking plate for optional VTH

pole mount

1 x Integrip carrying handle

| M10 x 3 flying inserts (portrait mounting)

1 x Integrip carrying handle Integral pole mount for standard 35 mm poles

Accessories|  |  |  |
 | Multi-Angle Wall Mount Multi-Angle Wall Mount-WH Yoke Horizontal VX 5.2/VX 6

Yoke Horizontal VX 5.2/VX 6 – WH

| Multi-Angle Wall Mount Multi-Angle Wall Mount-WH Yoke Horizontal VX 5.2/VX 6

Yoke Horizontal VX 5.2/VX 6 – WH VTH Top Hat

| Multi-Angle Wall Mount Multi-Angle Wall Mount-WH Yoke Horizontal VX8

Yoke Horizontal VX8 – WH Yoke Vertical VX8/VX8.2

Yoke Vertical VX8/VX8.2 – WH VTH Top Hat

|
 | VX 8.2 (-WH)| VX 12 (- WH)| VX 12HP (-WH)| VX 12Q (-WH)
---|---|---|---|---
System|  |  |
Frequency response| 80 Hz – 35 kHz ±3 dB

60 Hz – 45 kHz -10 dB

| 70 Hz – 25 kHz ±3 dB

55 Hz – 38 kHz -10 dB

| 80 Hz – 25 kHz ±3 dB

60 Hz – 30 kHz -10 dB

| 80 Hz – 25 kHz ±3 dB

60 Hz – 30 kHz -10 dB

Nominal dispersion| 90° conical @ -6 dB point| 90° conical @ -6 dB point| 75° conical @ -6 dB point| 75° H x 40° V @ -6 dB points
Directivity factor (Q)| 8.1| 9.6| 10.1| 13
Directivity index (DI)| 9.2| 9.8| 10| 11.1
Power handling (IEC)

Passive Bi-amp

|

200 W continuous, 800 W peak

–

|

200 W continuous, 800 W peak

–

|

350 W continuous, 1,400 W peak LF: 350 W continuous, 1,400 W peak HF: 80 W continuous, 320 W peak

|

350 W continuous, 1,400 W peak LF: 350 W continuous, 1,400 W peak HF: 80 W continuous, 320 W peak

Sensitivity| 93 dB (1 W @ 1 m)| 97 dB (1 W @ 1 m)| 97 dB (1 W @ 1 m)| 97 dB (1 W @ 1 m)
Maximum SPL

Passive Bi-amp

|

116 dB continuous, 122 dB peak

–

|

120 dB continuous, 126 dB peak

–

|

123 dB continuous, 129 dB peak LF: 124 dB continuous, 130 dB peak HF: 125 dB continuous, 131 dB peak

|

123 dB continuous, 129 dB peak LF: 124 dB continuous, 130 dB peak HF: 127 dB continuous, 132 dB peak

Impedance Passive Bi-amp|

8 Ω

–

|

8 Ω

–

|

8 Ω

8 Ω

8 Ω

|

8 Ω

8 Ω

8 Ω

Crossover Type| Passive with dynamic HF protection| Passive with HF protection| Passive / Bi-amp switchable| Passive / Bi-amp switchable
Components| 1 x 8″ (200 mm) LF driver

1 x 8″ (200 mm) constant directivity Dual Concentric

| 1 x 12″ (305 mm) constant directivity Dual Concentric| 1 x 12″ (305 mm) constant directivity PowerDual| 1 x 12″ (305 mm) constant directivity PowerDual with Q-Centric waveguide
Enclosure
Connectors| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2x Neutrik speakON NL4 1 x barrier strip terminals
Wiring

Passive Bi-Amp

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

–

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

–

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

Pins 1+ / 1- LF, Pins 2+ / 2- HF

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

Pins 1+ / 1- LF, Pins 2+ / 2- HF

Dimensions (H x W x D)| 591 x 281 x 276 mm

(23.3 x 11.1 x 10.9″)

| 487 x 371 x 361 mm

(19.2 x 14.6 x 14.2″)

| 487 x 371 x 361 mm

(19.2 x 14.6 x 14.2″)

| 487 x 371 x 361 mm

(19.2 x 14.6 x 14.2″)

Net weight| 14.8 kg (32.6 lbs)| 16.5 kg (36.3 lbs)| 20 kg (44.0 lbs)| 20 kg (44.0 lbs)
Construction| 15 mm (5/8″) plywood, vented and internally braced| 15 mm (5/8″) enclosure / 18 mm (3/4″) front, plywood, vented and internally braced| 15 mm (5/8″) enclosure / 18 mm (3/4″) front, plywood, vented and internally braced| 15 mm (5/8″) enclosure / 18 mm (3/4″) front, plywood, vented and internally braced
Finish| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M10 x 4 flying inserts M10 x 2 yoke bracket inserts 2 x Integrip carrying handle Blanking plate for optional VTH pole mount| M10 x 8 flying inserts (portrait or landscape mounting)

M10 x 8 yoke bracket inserts 2 x Intergrip carrying handles Blanking plate for optional VTH pole mount Compatible with the industry standard brackets M6 x 4 inserts

| M10 x 8 flying inserts (portrait or landscape mounting)

M10 x 8 yoke bracket inserts 2 x Intergrip carrying handles Blanking plate for optional VTH pole mount Compatible with the industry standard brackets M6 x 4 inserts

| M10 x 8 flying inserts (portrait or landscape mounting)

M10 x 8 yoke bracket inserts 2 x Intergrip carrying handles Blanking plate for optional VTH pole mount Compatible with the industry standard brackets M6 x 4 inserts

Accessories|  |  |  |
 | Yoke Horizontal VX8.2 Yoke Horizontal VX8.2 – WH Yoke Vertical VX8/VX8.2

Yoke Vertical VX8/VX8.2 – WH VTH Top Hat

| Yoke Horizontal VX12 Yoke Horizontal VX12 – WH Yoke Vertical VX12/VX12.2

Yoke Vertical VX12/VX12.2 – WH VTH Top Hat

| Yoke Horizontal VX12 Yoke Horizontal VX12 – WH Yoke Vertical VX12/VX12.2

Yoke Vertical VX12/VX12.2 – WH VTH Top Hat

| Yoke Horizontal VX12 Yoke Horizontal VX12 – WH Yoke Vertical VX12/VX12.2

Yoke Vertical VX12/VX12.2 – WH VTH Top Hat

55 Hz – 30 kHz -10 dB

| 70 Hz – 25 kHz ±3 dB

58 Hz – 30 kHz -10 dB

| 70 Hz – 25 kHz ±3 dB

58 Hz – 30 kHz -10 dB

Nominal dispersion| 75° H x 40° V @ -6 dB points| 75° conical @ -6 dB points| 75° H x 40° V @ -6 dB points
Directivity factor (Q)| 13| 9.7| 12
Directivity index (DI)| 11.1| 9.9| 10.8
Power handling (IEC)

Passive Bi-amp

| 500 W continuous, 2,000 W peak LF: 350 W continuous, 1,400 W peak

MF/HF: 350 W continuous, 1,400 W peak

| 400 W continuous, 1,600 W peak LF: 400 W continuous, 1,600 W peak HF: 80 W continuous, 320 W peak| 400 W continuous, 1,600 W

LF: 400 W continuous, 1,600 W HF: 80 W continuous, 320 W peak

Sensitivity| 99 dB (1 W @ 1 m)| 99 dB (1 W @ 1 m)| 99 dB (1 W @ 1 m)
Maximum SPL

Passive Bi-amp

| 126 dB continuous, 132 dB peak LF: 123 dB continuous, 129 dB peak HF: 127 dB continuous, 133 dB peak| 125 dB continuous, 131 dB peak LF: 126 dB continuous, 132 dB peak HF: 125 dB continuous, 131 dB peak| 125 dB continuous, 131 dB peak LF: 126 dB continuous, 132 dB peak HF: 127 dB continuous, 132 dB peak
Impedance Passive Bi-amp| 8 Ω

8 Ω

8 Ω

| 8 Ω

8 Ω

8 Ω

| 8 Ω

8 Ω

8 Ω

Crossover Type| Passive / Bi-amp switchable| Passive / Bi-amp switchable| Passive / Bi-amp switchable
Components| 1 x 12″ (305 mm) constant directivity PowerDual with Q-Centric waveguide

1 x 12″ (305 mm) LF driver

| 1 x 15″ (380 mm) constant directivity PowerDual| 1 x 15″ (380 mm) constant directivity PowerDual
Enclosure
Connectors| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2x Neutrik speakON NL4 1 x barrier strip terminals| 2x Neutrik speakON* NL4 1 x barrier strip terminals
Wiring

Passive Bi-Amp

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

Pins 1+ / 1- LF, Pins 2+ / 2- HF

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

Pins 1+ / 1- LF, Pins 2+ / 2- HF

|

Pins 1+ / 1- Input, Pins 2+ / 2- Link

Pins 1+ / 1- LF, Pins 2+ / 2- HF

Dimensions (H x W x D)| 781 x 371 x 361 mm

(30.7 x 14.6 x 14.2″)

| 591 x 451 x 421 mm

(23.3 x 17.8 x 16.6″)

| 591 x 451 x 421 mm

(23.3 x 17.8 x 16.6″)

Net weight| 30.5 kg (67.2 lbs)| 25.5 kg (56.2 lbs)| 25.4 kg (55.9 lbs)
Construction| 15 mm (5/8″) enclosure / 18 mm (3/4″) front, plywood, vented and internally braced| 18 mm (3/4″) enclosure / 18 mm (3/4″) front, plywood, vented and internally braced| 18 mm (3/4″) enclosure / 18 mm (3/4″) front, plywood, vented and internally braced
Finish| Semi matt black paint (white optional)| Semi matt black paint (white optional)| Semi matt black paint (white optional)
Grille| Powder-coated perforated steel| Powder-coated perforated steel| Powder-coated perforated steel
Flying hardware| M10 x 8 flying inserts (portrait or landscape mounting)

M10 x 8 yoke bracket inserts 2 x Intergrip carrying handles

Blanking plate for optional VTH pole mount

| M10 x 8 flying inserts (portrait or landscape mounting)

M10 x 8 yoke bracket inserts 2 x Intergrip carrying handles

Blanking plate for optional VTH pole mount Compatible with industry-standard brackets M6 x 4 inserts

| M10 x 8 flying inserts (portrait or landscape mounting)

M10 x 8 yoke bracket inserts 2 x Intergrip carrying handles

Blanking plate for optional VTH pole mount Compatible with industry-standard brackets M6 x 4 inserts

Accessories|  |  |
 | Yoke Horizontal VX12.2 Yoke Vertical VX12/VX12.2

Yoke Vertical VX12/VX12.2 – WH VTH Top Hat

| Yoke Horizontal VX15 Yoke Vertical VX15 VTH Top Hat| Yoke Horizontal VX15 Yoke Vertical VX15 VTH Top Hat

Other important information

Important information

1. Register online. Please register your new Music Tribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable.

2. Malfunction. Should your Music Tribe Authorized Reseller not be located in your vicinity,
   you may contact the Music Tribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.

3. Power Connections. Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.

Hereby, Music Tribe declares that this product is in compliance with Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC, and this passive product is not applicable to EMC Directive 2014/30/EU, LV Directive 2014/35/EU.

• Full text of EU DoC is available at https://community.musictribe.com/.
• EU Representative: Music Tribe Brands DK A/S
• Address: Gammel Strand 44, DK-1202 København K, Denmark
• UK Representative: Music Tribe Brands UK Ltd.
• Address: 6 Lloyds Avenue, Unit 4CL London EC3N 3AX, United Kingdom.

References

• Music Tribe
• Tannoy | Home
• Music Tribe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>